How to log into the settings of the Xiaomi 4C router: all ways and solutions to problems

Complete guide to accessing the Xiaomi Mi Router 4C control panel

Xiaomi Mi Router Router 4C It remains a popular choice due to its balance of price and functionality, but many users face difficulties when first logging into its web interface. Unlike current models with the Mi Wi-Fi mobile app, this version requires manual configuration via the browser – and here the questions begin: which one is the best one? IP-Use the address, where to find the factory login and password, and what to do if the page does not open.

In this article, we will analyze all the current ways to enter the settings of Xiaomi. 4C, including alternative methods for cases where the standard 192.168.31.1 We will pay special attention to typical errors (for example, ERR_CONNECTION_REFUSED) And how to fix them without resetting them to factory settings, and if you've just unpacked your device or are trying to restore access after you change your password, here's the solution.

Preparation for entry: what to check before starting

Before you try to go to the control panel, make sure that the basic conditions are met, most often access problems arise from improper connection or network settings on your device.

Here is the checklist before entering:

☑️ Preparation for the entrance to the Xiaomi router 4C

Connect the router to the outlet and wait for the stable burning of the power indicatorLAN-cableTurn off Wi-Fi on your device and leave only a wired connectionCheck that the computer is on receipt IP-address (DHCP)Close VPNs and proxy servers that can block local addresses

Done: 0 / 5

If you connect over Wi-Fi, make sure you are connected to the network. Xiaomi_XXXX (The default Wi-Fi password is on the sticker below the device — it should not be confused with the password to log into the control panel!

💡

On some Xiaomi 4C firmware, the factory Wi-Fi password may match the admin panel password. If the sticker is erased, try admin/admin or root/toor (for older versions).

Standard method of entry: through IP-address 192.168.31.1

The primary address for accessing Xiaomi Mi Router 4C settings is 192.168.31.1. This IP is spelled out in the default firmware and should work regardless of the software version. However, there are nuances that many people are unaware of.

Step-by-step:

Open any browser (Chrome, Firefox, Edge) and type in the address bar: http://192.168.31.1 Important: don’t add www or.com – it’s a local address, not a site.
If the page does not open, try alternatives: 🔹 http://miwifi.com (domain name Xiaomi) 🔹 192.168.1.1 (Sometimes used in old silk)
Enter the authorization window: 🔑 Login: Admin (default) 🔑 Password: Admin or the one on the router sticker

What happens if the page 192.168.31.1 does not open?

If the browser makes an error ERR_CONNECTION_TIMED_OUT, check: 1. Physical connection: cable must be inserted into port LAN (yellow connector, not WAN (blue-colored). 2. Network settings on PC: go to the Control Panel → Network and Internet → Network control centre → Change the adapter settings, select your connection, right-click → Properties → IP version 4 (TCP/IPv4) → Put the boxes on automatic receipt IP and DNS. 3. Antivirus/firewall: temporarily disable them – they can block access to local addresses. 4. Browser cache: try to open the address in incognito or other browser.

Critical detail: If you have previously changed IP-router address (for example, to 192.168.0.1), standard 192.168.31.1 In this case, the only way is to reset the settings to the factory (see section below) or connect via Telnet/SSH (power-user).

Alternative ways to log in: if the standard IP is not working

If 192.168.31.1 is not available and resetting is not desirable for some reason, there are a few workarounds that will require a little more effort, but often save in difficult situations.

Method 1: Determine the current IP router via the command line

This method works if your computer receives IP-router (DHCP included).

Press Win + R, enter cmd and press Enter.
In the command line, run: ipconfig /all
Find the main gateway line, which is your router's current IP. Enter it in your browser.

Method 2: Connect via Mi Wi-Fi (limited functionality)

The official Mi Wi-Fi app (available for Android and iOS) can connect to the router even without knowing IP, but with the following reservations:

📱 It only works if the router is connected to the Internet (via the Internet). WAN-port).
🔧 Only gives access to basic settings (change Wi-Fi password, turn on guest network).
⚙️ A web interface will still be required for full control.

📊 What router login method do you use more often?

Through IP-browser

Through the Mi Wi-Fi app

Through Telnet/SSH

I don't know how to get in.

Method 3: Using Telnet (for advanced users)

If you have Telnet enabled (default disabled), you can try connecting via the console:

Install PuTTY or use the built-in Windows Telnet client.
Connect to the router’s IP (e.g., 192.168.31.1) via port 23.
Enter the username/password (root/admin or root/toor) by default.

⚠️ Warning: This method requires command line knowledge and can cause the router to fail when the instructions are wrong.

Resetting router settings: when nothing helps

If all methods are exhausted and the control panel is not accessed, then the hardware reset remains, which will return the router to the factory settings, including the control panel. IP-address, login and password.

How to reset the Xiaomi Mi Router 4C:

Find a small hole on the back of the router that says RESET.
Take a paperclip or toothpick, press and hold the button for 10-15 seconds until the indicators start flashing.
Release the button and wait for the reboot (1-2 minutes).

After discharge:

🔄 IP-address will return to 192.168.31.1.
🔐 The login/password will become admin/admin.
📡 Wi-Fi settings (network name and password) will also reset.

💡

Resetting to factory settings is a last resort, after which you will have to configure the router from scratch, including connecting to an Internet service provider (PPPoE, L2TP, etc.).

⚠️ Note: On some of the firmware Xiaomi 4C After the reset, you may need to re-link to your Mi Account. If the router was purchased from hand, the previous owner could have linked it to his account – in this case, you will need to contact him to unbundle or use alternative firmware (for example, Padavan).

Table: Frequent Entry Errors and Their Solutions

Mistake.	Possible cause	Decision
ERR_CONNECTION_REFUSED	The router is not responding to requests, may be turned off or faulty	Check power, cables, try another browser or device
Wrong login or password	Password has been changed or entered with an error	Reset your settings or try admin/password, root/toor
The page is loaded, but in Chinese	Firmware with regional restrictions	Change the language in the settings or run the global version of the software
192.168.31.1 redirects to search engine	IP-Router address changed or conflict with other device on the network	Find the current IP via ipconfig or perform a reset
No access to certain settings sections	You have guest rights, not administrator rights.	Sign in with your admin account or reset your password

Additional settings after entry

When you finally get to the Xiaomi Mi Router 4C control panel, it’s recommended to do a few key steps for security and optimization:

Change the administrator password: Go to Settings → System → Password and set a strong combination (at least 8 characters with numbers and letters).
Update firmware: In the Software Update section, check the version's relevance. New firmware fixes vulnerabilities and adds features.
Set up Wi-Fi: In Wireless mode, change the network name (SSID), set a password (WPA2-PSK is recommended), select a channel manually (e.g., 6 or 11 for less interference).
Activate guest network: Useful for access differentiation (guests will not be able to log into the main network). → Guest network.

💡

If your Xiaomi 4C model does not have a Software Update section, you have custom firmware installed (like Padavan), in which case you should look for updates on forums like 4PDA or OpenWRT.

Frequently Asked Questions (FAQ)

Can I log into the Xiaomi 4C router without cable, only via Wi-Fi?

Yes, but with reservations. You must be connected to the router network (not to another access point), but when you first set up or crash, you better use a wired connection, which is more stable and eliminates DHCP problems.

I forgot my router password. How do I reset it without losing my settings?

Unfortunately, there is no way to recover a password without resetting. All methods (including Telnet) require knowledge of the current password. The only way out is to reset the hardware with the RESET button, but this will delete all settings.

After resetting, the router requires a link to the Mi Account. What to do if the previous owner did not untidy it?

This problem is typical of hand-built devices: 📧 Contact the previous owner and ask to untie the router in the Mi Wi-Fi app. 🔧 Swipe an alternative firmware (e.g., Padavan) that bypasses account binding. 📦 Contact Xiaomi with proof of purchase (check), but the chances of success are low.

Can you control Xiaomi 4C through your phone without logging in to the control panel?

Partially. Mi Wi-Fi app allows you to: 📶 Turn Wi-Fi on/off. 🔄 Reboot the router. 📊 View connected devices, but to change IP-address, DNS, Ports or firmware will still require a web interface.

What other firmware can be installed on Xiaomi 4C?

Popular alternatives: 🌐 Padavan - advanced settings, support VPN, AdBlock. 🐧 OpenWRT – for experienced users, full control over the router. 🔄 Stock Global – official firmware without reference to the Chinese region. ⚠️ Warning: Incorrect firmware can turn a router into a brick. 4PDA or GitHub.