How to log into the settings of the Xiaomi router 4C: 3 proven methods

Xiaomi Router Router 4C — One of the brand's most popular budget routers, but its settings often raise questions among users. 4A or AX3600, This device has a stripped-down web interface, and logging into the control panel requires a few nuances. IP-Addresses, login and password you can not change the settings of Wi-Fi, configure the guest network or update the firmware.

In this article, we will analyze all the current ways to enter the settings of Xiaomi. 4C, Including the standard browser method, alternative access via miwifi.com, and emergency login after a reset, we will focus on common errors (for example, when a page does not open or the router requires authorization through Mi Account) and how to fix them. If you are first configuring the device or faced problems after updating the firmware – here you will find solutions.

1. Standard entrance through IP-address 192.168.31.1

The main way to get into the settings of Xiaomi Router 4C — localize IP-The default address is 192.168.31.1, but it may be different in some firmware. Importantly, the router must be connected to a computer or smartphone via cable (recommended) or Wi-Fi.

Instructions:

• 🔌 Connect the router to the power source and wait until the indicator SYS It will blink or burn continuously (usually in 30 to 60 seconds).
• 💻 Connect Xiaomi 4C PC/laptop LAN-port (use the cable from the kit). Alternatively, connect to the router's Wi-Fi network (the default network name: Xiaomi_XXXX).
• 🌐 Open any browser (Chrome, Edge, Firefox) and type in the address bar 192.168.31.1.
• 🔐 Enter your login and password. It's a combination by default. admin/admin (New firmware may require authorization through Mi Account.

If the page does not load:

• 🔄 Try another browser or clear the cache (Ctrl)+Shift+Del).
• 📡 Make sure your device receives IP-address from the router (network connections must have the status "Connected").
• 🔧 Check if it's changed. IP-router address (see section 3).

⚠️ Note: If after the entry admin/admin If you have an error, "Incorrect password" means that the login data has been changed before, you will need to reset your settings.

2. Alternative access via miwifi.com

Xiaomi has provided a simplified way to log in to settings through the domain name miwifi.com.

• 🔢 You don't remember. IP-router.
• 🔄 192.168.31.1 is not working (for example, after changing the subnet).
• 📱 Configure a router from a smartphone, where it is difficult to enter numbers.

How to use:

1. Connect to the Xiaomi network 4C (cable-wire).
2. In the browser, type miwifi.com and click Enter.
3. Sign in with the same data as for IP-address (admin/admin).

If the domain does not open:

• 🔍 Check if the antivirus is blocking access (for example, Kaspersky or Avast may consider it phishing).
• 📡 Make sure that DNS-Router servers are not changed (by default should be 114.114.114 and 8.8.8.8).

3. How to find out the current IP-router

If the standard address 192.168.31.1 doesn't work, it may have been changed manually or lost after the update. IP:

On Windows:

1. Press Win + R, enter cmd and execute the command: ipconfig /all
2. Find the "Principal Gateway" line - that's it. IP your router.

On Android:

1. Open the Wi-Fi Analyzer app or go to Settings → Wi-Fi → [your network] → Additionally.
2. Look at the Gateway or Router field.

Nana macOS/iOS:

• 🍎 In System settings → Network → Additionally. → TCP/IP Find the router".
• 📱 On iPhone go to Settings → Wi-Fi → (i) close to the network → Router.

💡

If the router is IP from another subnet (e.g, 192.168.1.x), Try entering the first address of this subnet in the browser - 192.168.1.1.

4. Entry after resetting to factory settings

If you forget your password or the router is unstable, you may need a hardware reset. 4C This is done by the Reset button on the back, and it's important that after you reset, all settings (including Wi-Fi, passwords and guest network) will be deleted.

Step-by-step:

1. 🔌 Turn on the router and wait for the load (indicator) SYS constantly burning).
2. 📍 Find the Reset button on the back (usually in the recess).
3. 🔘 Press and hold the button for 10-15 seconds (until all indicators flash).
4. 🔄 Release the button and wait for the reboot (1-2 minutes).

After discharge:

• 🔐 Login and password will become standard: admin/admin.
• 📡 The name of the Wi-Fi network will be reset to Xiaomi_XXXX (where XXXX — last-minute MAC-address).
• ⚠️ If the router was linked to Mi Account, re-authorization may be required.

⚠️ Note: On some of the firmware Xiaomi 4C After the reset, you need to connect to the Internet for the initial setup, and if the provider's cable is not connected, the web interface may not open.

5. Solving entry problems

Even with the right one. IP-Address and password of Xiaomi users 4C They're all going to have common mistakes:

5.1. Page won't open (ERR_CONNECTION_TIMED_OUT)

Causes and solutions:

• 🔌 No connection to the router: Check the cable (should be in the LAN-port WAN) Or reconnect to Wi-Fi.
• 🔧 Wrong. IP-Address: Check the current address via ipconfig (see Section 3).
• 🛡️ Firewall Block: Temporarily disable Windows Defender or Antivirus.
• 🔄 Router crash: Turn it off for 30 seconds, then turn it on again.

5.2 Authorization requirement via Mi Account

Xiaomi’s firmware may have a window after 2022 asking for Mi Account data, which is linked to the brand’s security policy.

• 📱 If the router is linked to your account, enter the username and password from Mi Account.
• 🔄 If your account is forgotten, reset your router to factory settings (see Section 4).
• 🔧 For old firmware, you can roll back to the untethered version (but it is risky!).

Error "Incorrect password" with standard data

If you have never changed your password, admin/admin It's not a good fit, it's likely that the router was stitched with an alternative firmware (like Padavan or OpenWRT:

• 🔍 Clarify the firmware version (usually indicated on the sticker below).
• 📖 Look for instructions for your custom firmware (passwords may differ: root/admin, ubnt/ubnt etc.).
• 🔄 Reset (Section 4) and run the official firmware through MiWiFi.

💡

If the router requires authorization through Mi Account, and you do not remember it – the only way out (except for hacking) is a complete reset with the loss of all settings.

6. Set up router after login

After successfully logging into the Xiaomi web interface 4C You'll see the main page with the basic parameters:

6.1. Basic settings (Wi-Fi, password)

Path: Settings → Wireless mode (Wi-Fi)

• 🔄 Name of the network (SSID): Change to unique (do not use personal data!).
• 🔐 Password: Minimum length – 8 characters, a combination of letters, numbers and characters is recommended.
• 📡 Channel and width: For 2.4 GHz, select channel 1, 6, or 11 (less loaded).

6.2 Internet setting (WAN)

Path: Settings → Internet

• 🔌 Connection type: Select PPPoE (if the provider requires a login/password) or Dynamic IP (DHCP).
• 📡 DNS: Use 1.1.1.1 (Cloudflare) or 8.8.8.8 (Google) to speed up the Internet).

Guest access and parental control

Path: Settings → Guest Wi-Fi or Parental Control

• 👥 Guest Wi-Fi: Enable a separate network with limited access to local devices.
• ⏰ Schedule: Limit access times for children (e.g. 20:00 to 8:00).

7. firmware update and recovery

Regular update of Xiaomi firmware 4C It fixes vulnerabilities and improves stability, but an incorrect update can make the device tick.

7.1 How to update firmware

Official method:

1. Go to Settings. → Update.
2. Click "Check Updates."
3. If a new version is available, confirm the installation and wait for the restart (5-10 minutes).

Alternative method (if the automatic update does not work):

• 🔍 Download the firmware from the official Xiaomi website (Mi Router support section) 4C).
• 💾 Upload the file through Settings → Update → Local Update.

⚠️ Warning: Do not turn off the router during the upgrade! If the process is interrupted, you will need to restore through the TFTP (technical skills).

Recovery after failure

If the router is not turned on or constantly flashing SYS:

1. 🔌 Turn off the power for 30 seconds, then turn it on again.
2. 🔄 If it doesn’t work, reset (Section 4) and try to ask around.
3. 🛠️ As a last resort, use it. TFTP-mode (requires connection to the LAN and specialty software).

FAQ: Frequent questions