How to set up IPTV on Xiaomi AX3000 router: a complete guide with solutions to typical errors

Why Xiaomi AX3000 is good for IPTV – and where are the pitfalls

The Xiaomi AX3000 (RA73) is marketed as a universal Wi-Fi 6 home solution, but its IPTV capabilities are often left in the shadows. Unlike budget models, it features gigabit ports and hardware packet acceleration, which is critical for stable streaming. However, without the right settings, even the top-end router will “brake” channels — especially if your provider uses IGMP Proxy or VLAN binding.

The main problem is that the image freezes or no list of channels after connecting, which is due to the fact that by default the Xiaomi AX3000 is not optimized for multicast traffic (which is the basis of IPTV). In this article, we will analyze 3 ways of setting up (for different providers), fix typical errors and show how to check the flow rate without special programs.

⚠️ Important: if your provider uses PPPoE with a binding MAC-address, first, close MAC old router, otherwise IPTV It just won’t work, even with the right settings.

Method 1: Set up IPTV via IGMP Proxy (for most providers)

IGMP is responsible for managing multicast streams, which is what ISPs use to broadcast TV channels. On the Xiaomi AX3000, this protocol is disabled by default, so the first thing you need to do is activate it.

Instructions:

1. Open the router’s web interface at 192.168.31.1 (the default login and password is the combination of a sticker on the bottom of the device).
2. Go to Additional settings → Network → IPTV.
3. Turn on the IGMP Proxy switch and select Bridge mode (if the provider requires port binding).
4. In the field LAN-port IPTV Specify the port to which you are connected. STB-prefix or smart TV (For example, Port 4).
5. Save the settings and restart the router.

⚠️ Note: if after saving the settings, the Internet disappears - check whether it conflicts. VLAN ID for IPTV Some providers (e.g. Rostelecom) use a separate connection. VLAN for television, and you need to manually specify it in the Additional settings section → Local area network → VLAN.

Activated. IGMP Proxy|Choosing the right one LAN-port|The port is not occupied by another device|Provider does not require VLAN for IPTV-->

Method 2: Manual creation of VLAN for IPTV (for Rostelecom, MGTS, Beeline)

If your ISP uses a separate VLAN for IPTV (for example, a VLAN 100 for Rostelecom or a VLAN 300 for MGTS), standard IGMP Proxy configuration will not be enough, in which case you need to manually create a virtual network and link it to a physical port.

Step-by-step:

1. Go to the Additional settings → Network → VLAN.
2. Click Add and fill in the fields: 🔹 Name. VLAN: IPTV (arbitrary) 🔹 ID VLAN: Check with the provider (e.g. 100) 🔹 Ports: Select the port to which the console is connected (e.g. Port 3) and mark it as Tagged.

IPTV

VLAN

VLAN for IPTV

Save and restart the router.

💡 Advice: if after setting up VLAN No channels appear, check if the router firewall blocks multicast traffic. SPI Firewall in the Security section → Main settings.

Method 3: Configure via DHCP Option (for complex networks)

Some providers (e.g. TTKs or local operators) use DHCP Option for identification IPTV-In this case, the standard settings Xiaomi AX3000 will not work – you need to manually write the parameters in the configuration DHCP.

How to do this:

1. Go to Additional Settings → Network → Local Network → DHCP.
2. In the section Additional parameters DHCP add a line: option:60, "IPTV_STB" (significance IPTV_STB It may be different – check with the provider).
3. Save the settings and restart. DHCP-server (Reset button in the same section).

⚠️ Note: if the Internet stops working on other devices after this manipulation, then the provider uses Option 60 to authorize all customers, in which case you will have to return the settings and use cloning. MAC.

Problem Solving: Why Canals Are Not Working or Paining

Even after the right setup IPTV There may be problems.-5 causes and ways of eliminating them:

• 📶 Low Internet speed: IPTV minimum 15-20 Mbps for HD-Check the speed on Speedtest and compare it to the fare. If the speed is lower, contact the provider.
• 🔌 Incorrect port: if you have specified Port 4 for IPTV, But we've connected the console to Port 1, the channels won't load.
• 🔄 Conflict VLAN: if you have several VLAN (for example, for the Internet and TV), Make sure they don’t cross over. ID.
• 🛡️ Firewall lock: turn off SPI Firewall and DoS protection in 5-minute security settings – if channels are running, the problem is filtering rules.
• 🔄 Outdated firmware: in older versions of Xiaomi software AX3000 was a processing bug IGMPv3. Update your firmware to the latest version (see the Update section).

Critical error: if after setting up IPTV Internet stopped working on all devices - most likely, you specified VLAN ID for TV in the main settings of the WAN. In this case, you need to reset the router to factory settings (reset button for 10 seconds) and repeat the configuration.

💡

If the channels are slowed only in the evenings, the problem may be on the provider’s side. Try connecting to IPTV via a VPN (for example, WindScribe) – if the picture is more stable, the operator’s overloaded equipment is to blame.

Cloning MAC-Addresses: when necessary

Some providers (such as Dom.ru or Akado) link the service. IPTV ce MAC-If you replace the router, the TV may not work, even if all the settings are correct.

To circumvent this limitation, you need to bend MAC-address of the old router or STB-prefix:

1. Find out. MAC-address of the old device (usually listed on the sticker or web interface in the Status section) → Local area network).
2. In Xiaomi AX3000 go to Additional settings → Network → Internet.
3. Enable the Use option MAC-address and enter the cloned address.
4. Save the settings and restart the router.

⚠️ Attention: if you're cloning MAC-address STB-If the device is not a router, then the console must be connected directly to the router (and not through another switch), otherwise the provider can block the service for "duplicating devices".

Firmware Update: Why it's important for IPTV

In early versions of Xiaomi firmware AX3000 (up to 1.0.156) was a processing bug IGMP-It was a packet that lost multicast content and scattered channels into pixels, and the older versions didn't support it. VLAN Tagging for some providers.

How to update firmware:

1. Download the latest version from Xiaomi’s official website (select the RA73 model).
2. Go to Additional settings → System → Update firmware.
3. Click Select File and upload the downloaded image.
4. Wait until the process is completed (the router will restart automatically).

Note: If IPTV stops working after the update, reset to factory settings (Additional settings → System → Reset) and reset everything. New firmware versions can reset custom VLANs.

💡

Updating the firmware to version 1.0.156+ solves 80% of problems with IPTV hanging on the Xiaomi AX3000.

FAQ: Frequent questions about setting up IPTV on Xiaomi AX3000