Xiaomi Mouse Silent Edition: how to open the case without damage

Xiaomi Silent Edition’s wireless mouse has gained popularity with silent clicks, ergonomic design and long-term autonomy. However, over time, even such a reliable device may require internal cleaning: accumulated dust under the buttons, dried dirt on the sensor or wear of contacts. Disassembly of the case is the first step to diagnose malfunctions, but many users are afraid of damaging the latches or losing their warranty.

In this article, you'll find step-by-step instructions with a photo, a list of tools you need, and hidden nuances that are not covered in standard manuals. We'll also look at what actions can cause your sensor to break or lose communication with your Bluetooth transmitter, and how to avoid it. If your mouse starts to "glut" — double clicks, cursor getting stuck or spontaneous scrolling — most likely the problem lies inside the case.

⚠️ Critical warning: Disassembly of the device will void Xiaomi warranty.If the mouse is warranty, first contact the service center.Opening the case also risks damaging the battery seals (if any), making it impossible to replace it under warranty.

On the other hand, self-repair is often cheaper than buying a new mouse, for example, replacing micro-switches (omron keys) will cost 200-300 rubles, while the new Silent Edition costs from 1500 rubles.

Preparation for disassembly: tools and precautions

Before you get to the screwdriver, make sure you have everything you need. Inappropriate tools are the main reason for broken latches and scratches on the body.

• 🔧 Plastic mediator (or guitar) to disengage the latches. Metal screwdrivers leave traces!
• 🔍 Loop or magnifying glass – so as not to miss the hidden fixtures.
• 📸 Smartphone for photography – fix the location of parts before disassembling.
• 🧲 Magnetic mat or container – to avoid losing small screws.
• 🧴 Isopropyl alcohol (90%+) - for cleaning contacts and sensors.

Note: Xiaomi Silent Edition uses cross-shaped screws of the type PH00 (The smallest. The usual screwdriver. PH0 or PH1 If you don't have the exact size, you'd better buy a set of precision screwdrivers for 200-300 rubles.

⚠️ Warning: Do not use force when disengaging the body - if the latches do not respond, then you missed the hidden lock. In the Silent Edition there are only 6 of them, but one of them is hidden under a sticker with a serial number (it can be neatly put with a knife).

Step-by-step instructions: how to open the body

The disassembly process takes 10-15 minutes if you act carefully.

1. Turn off the mouse and remove the battery (if it is removable). In models with built-in battery, it is enough to turn off the power.
2. Turn the mouse down with the wheel. On the bottom lid, you'll see 4 screws -- spin them counterclockwise.
3. Insert the mediator in the gap between the top and bottom of the body (start from the wheel side). Carefully guide it around the perimeter until you hear clicks of snapping locks.
4. Remove the top cover, holding it by the wheel - inside the sensor plume may be glued.

⚠️ WARNING: If the mouse stopped turning on after removing the lid, check to see if the flexible plume has come off the board. In Silent Edition, it's often glued with double-sided tape - don't pull the lid sharply!

Now you will see the internal structure:

• 🖱️ Optical sensor (usually markings) PMW3360 or ADNS-3050).
• 🔋 Battery (in removable models - soldered connector).
• 🔘 Micro-switches (omron keys) under left and right buttons.
• 🌀 Encoder wheel - a common cause of "ghost scrolling».

Turn off the power of the mouse|

Photograph the location of the details|

Check the integrity of the plumes|

Do not touch the sensor with your fingers (tweezers only)-->

Cleaning and Diagnostics of Internal Components

Once the case is opened, the first thing you need to do is to look at the contacts and the sensor for contaminants. In 80 percent of cases, the mouse's glitches are caused by dust or oxidation. Here's how to clean properly:

Sensor (optical eye):

• 🧹 Remove dust with a soft brush (for example, for camera lenses).
• 💧 Wet the cotton swab in isopropyl alcohol and gently wipe the sensor lens without pressing.
• 🔍 Check if there are any scratches on the lens – if there is, the mouse will have to be replaced.

Micro-switches (buttons):

They're the ones that get out of order most often.

• 🔊 Double clicks with one click.
• 🛑 The button “sticks” or works again.
• 🔊 A sound appears when pressed (clicks must be silent in Silent Edition!).

For cleaning:

1. Remove the buttons by putting them under a plastic spatula (they are attached to the latches).
2. Blow the contacts of the micro-switches with compressed air (a canister for cleaning the keyboard).
3. If the oxidation is strong, wipe the contacts with alcohol.

⚠️ Warning: If the buttons are still double after cleaning, they need to be replaced.Omron micro-switches are suitable for Xiaomi Silent Edition D2FC-F-7N(10M) (silent) or D2FC-F-K(50M) (common but durable).

💡

Before you build, check the mouse without the top cover: connect it to Bluetooth and test the clicks. If the problem persists, it is not the case, but the board or firmware.

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when disassembling Xiaomi Silent Edition.-5 failures and their consequences:

Pay special attention to the scrolling wheel. In Silent Edition, it is often clogged with dirt, which causes it to "click" when scrolling.

1. Remove the wheel by pulling it up (it is held on plastic guides).
2. Remove dirt from the grooves with a toothpick soaked in alcohol.
3. Drop 1 drop of silicone lubricant on the encoder axis (don’t overdo it!).

Battery replacement: nuances for Xiaomi Silent Edition

In models with built-in batteries (such as the Mi Silent Mouse Pro), the battery loses capacity over time. If the mouse runs out in 2-3 days instead of the promised 12 months, it's time to change it. AA, but thinner) with tension 3.7V.

Step-by-step replacement:

1. Solder off the old battery from the board (use a soldering iron of 30-40 watts).
2. Sell a new battery while observing polarity (+ and - marked on the board).
3. Secure the battery with double-sided tape so it doesn't hang around.

⚠️ Note: Do not use batteries with a voltage higher 3.7V — And avoid cheap batteries without protection, they can swell.

Where to buy a replacement:

• 🛒 AliExpress – Search for “10440” 3.7V 380mAh».
• 🏬 Radio parts stores (for example, Chip and Deep»).
• 🔋 Donor mice – you can solder out the battery from the old Xiaomi Mouse.

💡

If the mouse does not charge after replacing the battery, check the fuse on the board (a small black chip next to the battery). USB-It can be replaced by a similar one with a nominal value. 0.5A.

Mouse assembly: how to prevent new problems

Collecting Xiaomi Silent Edition back is harder than disassembling. The main mistake is the wrong position of the plumes, which either causes the mouse to fail or the clicks to register curves.

1. Put the sensor plume in the groove on the bottom cover, and it should lie flat, without any inflections.
2. Secure the battery (if it is removable) or make sure the battery contacts are related to the board.
3. Line the upper cover along the guides (they are near the wheel and to the right of the left button).
4. Click the body, starting at the wheel side. You should hear 6 clicks.
5. Twirl the screws cross-cross so as not to skew the body.

After assembly, test the mouse:

• 🖱️ Check the smoothness of the cursor movement on a white background (should be absent jerks).
• 🔊 Press all buttons – clicks should be silent, no rattles.
• 🌀 Scroll the wheel – it should not “click” or scroll in jerks.

⚠️ Warning: If the wheel scrolls "on its own" after assembly, you have incorrectly installed the encoder. Take apart the mouse and check if there is any dirt between the contacts of the encoder and the board.

When the disassembly did not help: alternative solutions

If there's still a problem after cleaning and assembling, it might not be the mechanics.

Programmatic failures:

• 🖥️ Update your mouse drivers via Device Manager (Windows) or System Settings (macOS).
• 🔄 Reset your mouse settings in Mi Mouse Settings (official software from Xiaomi).
• 📱 Reconnect the mouse to the device: remove it from the list of Bluetooth devices and add again.

Hardware malfunctions:

If the mouse does not respond to movements or clicks, but the LED is on, the problem may be:

• 🔍 Sensores – Requires replacement (cost) ~500 rubles).
• 📡 Bluetooth module – check if the mouse can see other devices.
• 🔋 Power Controller – if the mouse is not charged at all.

In such cases, it is more appropriate to contact the service or buy a new mouse, and the cost of repairing the fee is 60-70% of the cost of a new device.

💡

Before buying a new mouse, check it for compatibility with your OS. Some Xiaomi models do not work well with macOS because of the drivers.

FAQ: Frequent questions about the Xiaomi Silent Edition disassembly