Xiaomi phone does not turn on: what to do if the device does not respond to the power button

You pressed Xiaomi's power button, but the screen is black, the indicators are not on, and the phone does not respond to charging? This is a situation familiar to many owners of smartphones of the brand - from the budget Redmi Note to the flagship Xiaomi 13. The reasons can range from a trivial battery discharge to serious hardware malfunctions, and solutions - from a simple reboot to flashing through Fastboot.

In this article, we’ll look at all possible scenarios for why Xiaomi doesn’t turn on, from software failures to physical damage, how to diagnose a problem yourself, what manipulations are worth trying first, and when it’s best to carry your phone to a service center right away. Special attention will be paid to the unique “chips” Xiaomi, which often cause problems: for example, why smartphones with MediaTek processors can “die” after a failed update, or how improper charging kills the power controller in models with Quick Charge 4.+.

If your phone still has any signs of life (vibrates, warms, flashes the indicator), the chances of recovery without repair are much higher. If the phone is completely dead, don't panic: 60 percent of the time the problem is solved at home. Let's start with the simplest.

1. Checking the obvious: charging, cables and power button

Before you commit to complex malfunctions, rule out three basic reasons why Xiaomi may not turn on:

• 🔋 Battery discharge – even if you “just” charged your phone, the battery could run out due to background activity or controller malfunction.
• 🔌 Charger problems – unoriginal cables or power supplies often don’t provide enough current to start.
• 🔘 Sticking the power button – dust, moisture, or mechanical wear can block contacts.

What to do:

1. Connect the original cable and power supply (preferably from Xiaomi with Quick Charge support). Leave the phone on charge for at least 30 minutes - even if the indicator is not on. Sometimes a discharged battery shows no signs of charging for the first 10-15 minutes.
2. Try another charger - the block from the laptop with an output is perfect USB-C (For example, from a MacBook or Dell XPS). Such adapters produce stable 18-20 watts, which is enough to "reanimate" a deeply discharged battery.
3. Perform a "hard reboot" - press the power button for 15-20 seconds. In some models (for example, Redmi 9 or the power button). POCO X3) This works even with a fully discharged battery.
4. Check the power button - if it "fails" or requires effort to press, it is possible that the contacts have oxidized. Carefully tap the button with the blunt side of the pencil (don't overdo it!).

If you're not showing any signs of life after this manipulation, move on to the next step, but first make sure that the problem isn't with the hardware lock.

⚠️ Note: Xiaomi smartphones with Qualcomm Snapdragon processors (for example, Redmi Note 10 Pro or Xiaomi) 11T) Sometimes, the protection against "deep discharge" is triggered. If the battery is discharged below 2.8 V, the controller blocks the charging until it receives a signal from the charger with a voltage higher than 9 V. In this case, only connecting to a powerful power supply unit will help.+ W) or “lighting” from another phone via OTG-cable.

2. Diagnosis by indirect signs: what do flashing, vibration and heating mean

If your phone is responding to you in any way, that's a good sign, and you can tell by the way you react, what's the problem?

Pay special attention to heating. If the phone gets too warm when connected to a charger, it may indicate:

• 🔥 Short circuit in the battery (dangerous! immediately disconnect from the network!).
• 🔌 Power controller malfunction (frequent problem in Redmi 9 and POCO M3).
• 🖥️ Firmware looped (for example, after a failed update via MIUI Updater).

If the phone vibrates but doesn’t turn on, it could be a sign:

• 📱 Sticking of the power button (vibration is triggered when pressed, but the signal does not reach the system).
• 🔄 Loaded loading (phone tries to turn on but falls on logo) MI).
• 🛠️ Firmware damage (for example, after manual update via TWRP).

3. Software failures: how to get out of looped boot or "brick"

If Xiaomi phone turns on but hangs on logo MI, It's rebooted in a loop or it's got a Fastboot Mode error, which is probably software problem, and 90 percent of the time it's treated without repair:

Scenario 1: The phone hangs on the logo MI or Redmi

This is a typical sign of a damaged firmware or conflict after an update, most commonly found in models with MediaTek processors (e.g. Redmi). 10A or POCO C31), where the system can "fly" even after an automatic update.

What to do:

1. Hard reset: press the power button + Volume up for 10-15 seconds until the phone restarts.
2. Entrance to Recovery Mode: 1. Turn off the phone (if it doesn't respond - press the power button for 20 seconds). 2. Press the power button + volume up. 3. Hold on until the logo menu appears. MI android.
3. In the Recovery menu, select Wipe Data → Wipe All Data (reset to factory settings) Attention! This will delete all data on the phone.
4. If the reset doesn’t help, choose Reboot. → Reboot to Bootloader and reflash your phone with the Mi Flash Tool.

Scenario 2: The phone is loaded into Fastboot Mode

If you turn on the Fastboot and you see a picture of a hare in a hat, it means that the system can't find the boot partition.

• 📦 Failed update through MIUI Updater.
• 🔧 Damage to the boot section after rooting.
• 🖥️ Failure to firmware through TWRP.

The solution is to flash your phone through the Mi Flash Tool:

Download the official firmware for your model from the Xiaomi Firmware website

Install Qualcomm or MediaTek drivers (depending on the processor)

Start the Mi Flash Tool and connect your phone in Fastboot mode

Select a firmware file with the.tgz extension and press Flash

Wait until the process is over (don’t turn it off). USB!)

-->

⚠️ Warning: Fastboot firmware erases all data on your phone, including photos and contacts. MIUI (Settings → Additionally. → Backups, they can be recovered after firmware is installed, otherwise the data will be lost.

Scenario 3: The phone turns on but immediately turns off

If Xiaomi starts to boot but shuts down after a few seconds, the reason could be:

• 🔋 Faulty battery (does not hold charge even when connected to the network).
• 🛠️ Damaged battery plume (frequent problem after falls).
• 📱 Processor overheating (for example, due to dried thermal paste).

Diagnosis:

1. Connect your phone to charge and try to turn it on. If it only turns off without a cable, the battery is a problem.
2. Light a flashlight on the screen at an angle - if the image is barely noticeable, the plume of the display or backlight is defective.
3. Try turning your phone on in Safe Mode (click the power button). + If it's stable in safe mode, one of the apps installed is to blame.

💡

If the phone turns off due to overheating, try cooling it in the fridge (not in the freezer!) for 10-15 minutes. If after that it turns on and works longer - a problem in the cooling system (requires replacement of thermopaste or heat pads).

4. Hardware malfunctions: when without repairs can not do

If all the software methods have been tried, but Xiaomi still doesn’t turn on, it’s probably a hardware problem.

1. Battery malfunction

Symptoms:

• 🔋 The phone is only turned on when connected to charging.
• 📉 The battery is discharged in a few minutes or shows an inadequate percentage (for example, jumps from 50% to 1%).
• 🔥 The phone is warming up in the battery area.

Reasons:

• Natural wear (Xiaomi batteries are designed for 500-800 charging cycles).
• Use of non-original chargers (cheap cables with AliExpress are especially dangerous).
• Mechanical damage (falls, bending of the phone).

Solution: battery replacement. Redmi Note models 8/9/10 It's worth about 1500–2500 ruble, in flagships (Xiaomi) 12/13) — 3000–5000 After replacing the battery, you need to calibrate the power controller through the engineering menu (##4636## → Battery information).

Damage to the power controller

Symptoms:

• 🔌 The phone does not respond to charging (even with the original cable).
• 📱 When connected to a PC, it is defined as Qualcomm. HS-USB QDLoader 9008 (Brick sign").
• 🔥 Strong heating in the area of the top of the phone (where the controller is located).

Reasons:

• Power surges when charging.
• Failed firmware through Fastboot.
• Getting moisture on the motherboard.

Solution: Replace the power controller (in the service center) in Qualcomm processor models (e.g. Xiaomi) 11T) It costs 3000-7000 rubles, in MediaTek (Redmi 10) - cheaper (2000-4000 rubles).

⚠️ Note: If the phone is defined as Qualcomm HS-USB QDLoader 9008, don't try to flash it with standard methods! IMEI. In such cases, restoration is required through EDL-Mode (only in service with an authorized Xiaomi account).

3. Maternity board malfunction

Symptoms:

• 💥 The phone does not turn on after falling or getting moisture.
• 📵 Complete lack of response to buttons and charging.
• 🔥 The smell of a smoke when trying to switch on.

Reasons:

• Short circuit after water is injected.
• Heap chips (for example, RAM or flash drive).
• Overheating of the processor (often in models with Snapdragon) 888/8 Gen 1, for example, Xiaomi 11 Ultra).

Solution: diagnostics at a service center, depending on the damage, you may need to:

• 🛠️ Interpling of microchips (from 5000 rubles).
• 🔧 Replacement of southern / northern bridges (from 10 000 rubles).
• 📱 Full replacement of the motherboard (30-70% of the cost of the phone).

💡

If the phone doesn't turn on after getting moisture, don't dry it with a hair dryer or rice! This will speed up the corrosion of the contacts. The best option is to take it to the service within 24 hours for ultrasound cleaning of the board.

5. Specific problems of Xiaomi models: what breaks most often

Xiaomi smartphones have a number of “diseases” specific to specific lines, and knowing these nuances will help to diagnose the problem faster:

Special attention should be paid to models with MediaTek processors (Redmi). 10A, POCO C31, Redmi 9A). These chips are more vulnerable to:

• 📱 Failures during the update (often "flying" firmware after the OTA-update).
• 🔌 Charging problems (power controller fails when using non-original cables).
• 🛠️ Overheating (due to weak cooling system).

If you have one of these models, be sure to check before you fix or repair:

1. Is the boot loader unlocked (Settings) → The phone. → Version. MIUI, slip 5 times).
2. Is there a backup of data (in MediaTek-models, data recovery after a reset is more difficult than in Qualcomm).
3. Whether the firmware is compatible with your board revision (e.g., Redmi Note 9 has global, eea, and india options).

6. Data recovery if the phone is not turned on

If Xiaomi has some important data (photos, contacts, messages) left on the idle, you can try to extract it even without fully turning on the phone.

Method 1: Connect to a PC in Fastboot mode or EDL

If the phone is defined by the computer as Qualcomm HS-USB Or MediaTek Preloader, there's a chance of data recovery:

• 🖥️ PC with Qualcomm or MediaTek drivers installed.
• 🛠️ The Mi Flash Tool program or SP Flash Tool (for MediaTek).
• 📱 Backup firmware for your model.

Instructions:

1. Connect your phone to your PC in Fastboot mode (power button) + volume).
2. Run the Mi Flash Tool and select the Save user data option (if available).
3. Press Refresh – the program must identify the phone.
4. Select Read (not Flash!) and save the memory dump on your PC.
5. Use a tool like Dr.Fone or 7-Zip file-extracting.

⚠️ Attention: Recovery from a memory dump is a complex process that requires skills in working with hex editors. If you are not confident in your abilities, contact a service specializing in chip-off recovery (cost from 5000 rubles).

Method 2: Removal of the microSD card (if installed)

If you had a memory card on your phone, you can read it on another device.

1. Remove the tray for SIM-cards (use a paper clip or special key).
2. Take care of the microSD (not to be confused with the microSD). SIM-card!).
3. Put it in another phone or card reader.
4. Copy the data on the PC.

If the card is not readable, try:

• 🔧 Connect it through a card reader with support UHS-I (Cheap adapters may not see the cards).
• 🛠️ Use data recovery software (Recuva, R-Studio).
• 📱 Check the card on another phone (sometimes the problem is in the PC drivers).

Method 3: Recovery via Xiaomi account (if synced)

If you have enabled your Mi Account and sync on your phone, some of the data can be restored via the cloud:

1. Go to i.mi.com and log in.
2. In the Cloud section, check for backups (Settings) → Cloud. → Backup).
3. Download the archive (if a copy was created recently).

What can be recovered from the cloud:

• 📇 Contacts and messages (if synchronization was enabled).
• 📷 Photos and videos (if uploaded to Mi Cloud).
• 📅 Calendar notes and records.

Unfortunately, apps and their data (such as WhatsApp or Telegram) are not restored through the Xiaomi cloud, but need a local backup on the phone or memory card.

7. When to contact the service: prices and guarantees

If all of these methods did not help, it is time to carry the phone for repair. Here are the approximate prices for popular types of work for Xiaomi smartphones (current for Moscow and the regions for 2026):

📖 Read it too.

How to find out the Xiaomi model: 7 proven ways

Do you know how to determine the model of your phone or Xiaomi TV? Learn all the methods - from the box to the box.

How to remove the cover Xiaomi Mi5: step-by-step disassembly instruction

Detailed guide: how to remove the back cover Xiaomi Mi5. Tools, risks, heating glue and steps

Why the light bulb on the Xiaomi TV flashes: causes and solutions

We understand why the indicator on Xiaomi TV flashes red, white or blue, and what to do to eliminate

How to get status error on socket receive on Xiaomi

Detailed instructions for fixing the socket receive error on Xiaomi smartphones and devices.

How to replace the curtain on Xiaomi: step-by-step instructions 2026

Detailed guide to self-replacement of curtains (IR-filter) on Xiao TVs and projectors

Disassembly Xiaomi Redmi Note 9: step-by-step instructions with photos

How to safely disassemble Redmi Note 9 for repair: tools, procedures and tips to avoid

📱 XiaoMaster

🔓 Reset and release

⚙️ System setup

💾 Memory and files

🔊 Sound and vibration

📸 Camera and photo

📡 Communications and networking

Mainstream

About the project

Contacts

Confidentiality

© XiaoMaster, all rights reserved.

(function(d,s){d.getElementById("licnt06C4").src= "https://counter.yadro.ru/hit?t26.5;r"+escape(d.referrer)+ ((typeof(s)=="undefined")?"":";s"+s.width+"*"+s.height+"*"+ (s.colorDepth?s.colorDepth:s.pixelDepth))+";u"+escape(d.URL)+ ";h"+escape(d.title.substring(0,150))+";"+Math.random()})(document,screen)

🍪 We use cookies to improve the operation of the website.

Accept