Xiaomi phone is not included and is defined as Qualcomm HS-USB QDLoader 9008: What to do?

If your Xiaomi smartphone has stopped turning on, and when you connect to your computer, the name Qualcomm is displayed in the Device Manager. HS-USB QDLoader 9008, which means that the device is in emergency booter mode, which is activated when critical firmware failures, failed updates or hardware memory problems. This most often happens after incorrect unlocking of the bootloader, interrupted firmware through MiFlash or physical damage to the eMMC chip.

The situation is complicated by the fact that in the 9008 mode the phone does not respond to power buttons, does not charge and is not determined by standard drivers. ADB. However, this is not a sentence – in 80% of cases, the device can be restored. In this article, we will analyze the causes of the problem, official and informal methods of solving, as well as nuances for different models Xiaomi, Redmi and other devices. POCO.

It's important to understand that the QDLoader 9008 mode is not just a brick, but a secure mode of the Qualcomm chip, designed for low-level memory access, which allows you to reflash the device even when the bootloader is completely erased. However, incorrect actions can lead to irreversible damage to the persist partition or blockage. IMEI, Follow the instructions carefully.

Why Xiaomi is moving to Qualcomm mode HS-USB QDLoader 9008?

The 9008 mode is activated by the Qualcomm Snapdragon processor when the main firmware cannot be loaded.

• 🔄 Failed update MIUI via Updater or Fastboot (especially when interrupting the process).
• 🔓 Mistakes when unlocking the bootloader via the Mi Unlock Tool (for example, if the Mi Account is not tied to the device).
• ⚡ Voltage drop during firmware (cable shutdown, battery discharge below 30%).
• 🛠️ Hardware failures: chip damage eMMC/UFS, oxidation of contacts or chip dumping of memory.
• 📱 Incompatible firmware: an attempt to install custom ROM for another model or version MIUI.
• 🔧 Reset via Hard Reset on a locked bootloader (e.g., Power retention) + Vol+ On the Redmi Note 8 Pro).

The most vulnerable devices with Snapdragon chips 6xx/7xx (For example, Redmi Note 7/8/9, POCO X3), Because their firmware often contains errors in modem and boot sections, while models on MediaTek (e.g. Redmi) 9A) mode 9008 They do not go through a similar emergency mode called BROM.

If you tried to root through Magisk or changed the system partition before the problem, the probability of a software failure is 95%.

How to check if your phone is in 9008 mode?

Before you start recovery, make sure that the device is in Qualcomm mode. HS-USB QDLoader 9008, and not in other emergency states (e.g., Fastboot or Fastboot) EDL). For that:

1. Connect the phone to the computer using the original USB-cable (better to use port) USB 2.0 on the back of the PC).
2. Open Device Manager (Win + X → Device Manager).
3. Check the section "Ports (COM and LPT)" or “Other devices".

If you see a device with a name:

• Qualcomm HS-USB QDLoader 9008 (or COMX) — That's the 9008 mode.
• Android Bootloader Interface is a phone in Fastboot mode.
• MediaTek Preloader is an emergency mode for MediaTek chips.
• Unidentified device – you need to install the driver QCOM_Driver.

Some models (e.g. Xiaomi Mi) A2) In 9008 mode, the phone can vibrate slightly when connected to the USB — If the device is not detected at all, check the cable, the port, or try another computer.

💡

If the Device Manager displays an exclamation point near Qualcomm HS-USB QDLoader 9008, download and install the driver manually through Driver Update → Perform a search on this computer → Select from the list

Official ways to restore Xiaomi from the 9008 mode

Xiaomi offers two legal ways to exit the 9008 mode:

1. Through the Mi Flash Tool (requires an unlocked bootloader).
2. Through an authorized service center (if the bootloader is blocked).

Mi Flash Tool is the official utility for firmware Xiaomi devices in mode EDL (And that's 9008, but it's a must:

• 🔓 Unlocked bootloader (if previously unblocked – you will need authorization through Mi Account).
• 📥 Official firmware.tgz for your model (downloaded from new.c.mi.com).
• 🖥️ Computer running Windows 7/10/11 (on macOS/Linux MiFlash is not working).

Step-by-step:

1. Download and install MiFlash (version 2020.3.14.0 or later).
2. Unpack the firmware archive into a folder without Cyrillic characters (e.g., C:\ROM\).
3. Run MiFlash.exe on behalf of the administrator.
4. Click Select and point the way to the firmware folder.
5. Connect your phone to 9008 (should be determined as) COMX).
6. In MiFlash, select the firmware method: Clean All – complete cleaning (recommended for critical failures). Clean All and Lock – cleaning + Locking the bootloader (if you want to return the device to the stock). Save User Data - an attempt to save data (does not always work).

Flash

If the firmware is successful, the phone will automatically reboot to Fastboot and then to the system. If there is a Critical Partition Flashing Is Not Allowed error, then the bootloader is blocked, you will need to unlock through the Mi Unlock Tool.

Unofficial methods: firmware through EDL corrective IMEI

If the official method did not work (for example, due to a blocked bootloader), you can use informal tools. IMEI, if not done correctly.

Method 1: Firmware via QFil (Qualcomm Flash Image Loader)

The QFil utility allows you to flash Qualcomm devices bypassing the restrictions of Xiaomi.

• 📌 Firmware in.mbn or.elf format (can be found on forums) 4PDA or XDA).
• 🔧 Qualcomm Driver HS-USB QDLoader 9008 (manually installed).
• 🛡️ Windows Defender disabled (it can block QFil).

Instructions:

1. Download and unpack QFil.
2. Run QFil.exe, press Browse and select the firmware file prog_emmc_firehose_*.mbn.
3. In the Select Port section, select COM-port corresponding to 9008.
4. Press Load. XML and upload the files rawprogram0.xml and patch0.xml.
5. Press Download and wait until it is completed (don’t turn off the cable!).

Method 2: Recovery IMEI post-fix

If it's gone after the firmware. IMEI (phone does not catch the network, it can be restored through the engineering menu:

1. Enter the dialer code: ##4636##.
2. Go to Phone Information and check for IMEI status.
3. If IMEI No, no, use the utility. QCN Rebuilder or Maui META For overwriting (requires a backup copy of.qcn).

⚠️ Note: Using unofficial firmware can result in a Mi Account being blocked (especially on models with Anti-Rollback like the Redmi Note). 8 Before you run the firmware, check the Anti version in the file. rawprogram0.xml.

Hardware causes of the 9008 mode and their diagnosis

If the software methods didn't work, the problem could be the hardware, and it's often the culprits.

• 💾 Damage to a memory chip (eMMC or UFS) — For example, due to overheating or falling.
• 🔌 Oxidation of contacts on the board (especially after moisture hits).
• 🔋 Failure of the power controller (the phone does not charge even when switched off).
• 📶 The antenna module dump (can block the load on some models).

For diagnosis:

1. Check the battery: connect the obviously working battery (if it is removable).
2. Check the board for blackened elements or bloated capacitors.
3. Call the power chain with a multimeter (if you have soldering skills).
4. Connect to DC Power Supply (Power Supply) – if the phone does not respond to 3.8–4.2V, problem.

Typical "symptoms" of hardware problems:

If you do not have experience in electronics repair, it is better to contact the service (BGA-station) in 90% of cases leads to a final breakage of the fee.

Frequent Recovery Mistakes and How to Avoid Them

Many users make the problem worse by making common mistakes, and this is what you can't do in 9008 mode:

• ❌ Use unofficial firmware without compatibility checks (for example, flash Redmi Note 8 with Note firmware) 8T).
• ❌ Interrupt firmware – even if the process “hangs” by 99%, wait for a timeout (10-15 minutes).
• ❌ Swipe through Fastboot - in 9008 mode this method does not work.
• ❌ Ignore Anti-Rollback: Firmware of the Old Version MIUI The new one will lead to a lockdown.
• ❌ Try to charge your phone in 9008 mode – the battery is not charging and the risk of short circuit increases.

Common MiFlash Errors and Their Solutions:

If MiFlash is making a mistake SAHARA (for example, SAHARA: Fail to switch to EDL mode, which means that the phone cannot go into mode EDL. In this case, only testpoint (closing contacts on the board) or an authorized service will help.

⚠️ Note: On Xiaomi models with Snapdragon chip 8xx (For example, Mi 9, Mi 10, trying to flash an unofficial firmware can lead to the blocking of the Mi Account even after the reset, in which case you will need to officially unlock through the service center.

Xiaomi models with frequent 9008 mode problems

Some Xiaomi devices are more likely to go to 9008 mode due to hardware or software features, and here is a list of the “problem” models and their nuances:

• 📱 Redmi Note 7/7 Pro (Snapdragon 660/675): He often goes on to 9008 After a failed bootloader unlock requires firmware with a Clean All and Lock tick in MiFlash.
• 📱 Redmi Note 8 Pro (MediaTek Helio G90T): Does not support the 9008 mode - instead it is used BROM. Recovery needs to be done. SP Flash Tool and an authorized MediaTek account.
• 📱 POCO X3 NFC (Snapdragon 732G): Sensitive to Anti-Rollback versions – firmware of the old version MIUI In the 9008 mode, it may require a testpoint for forced EDL.
• 📱 Mi A2/A3 (Android One: Does not have a standard recovery – if the firmware fails, it immediately goes into the system. 9008. Requires firmware via QFil with file prog_emmc_firehose_8953.mbn.
• 📱 Redmi 9/9A/9C (MediaTek Helio G35/G80): Regime. 9008 It is not supported, but instead BROM Or Meta Mode. You need to recover. SP Flash Tool + Auth File.

If your model is not on the list, check its chipset on the GSMArena website. For devices on MediaTek, the instructions in this article will not work - they require a separate guide for working with the device. BROM.

💡

Always check the firmware compatibility with your model and the Anti-Rollback version before you run the firmware. The inconsistency will result in the device being locked!

FAQ: Answers to Frequent Questions