The situation where your Xiaomi is showing signs of life, vibrating, but the screen gets stuck on the "Mi" or "Redmi" logo is one of the most common and intimidating for owners.This behavior, known as bootloop or bootloop getting stuck, can be caused by a software failure, a failed update or damage to system files.
Do not panic, because in most cases the device is not physically broken, but simply lost the ability to properly initialize the Android operating system. Before carrying the gadget to the service center, you need to exclude software errors that can be fixed yourself at home.
You need to be careful and follow instructions consistently, and we'll look at methods from simple restarts to complete computer flashing, which will help bring back even deeply locked devices.
Primary diagnosis and safe reboot
The first thing to do is to eliminate trivial interruption of temporary processes or battery discharge. If the Xiaomi phone turns on but does not load beyond the logo, a forced reboot often helps, which clears the RAM of erroneous commands.
Press the power button and hold it for 10-15 seconds. If the device doesn't respond, try the Power Button + Volume Up combination. The screen should go out, after which the vibration will signal the start of a new boot cycle.
⚠️ Warning: If your phone is connected to charging, make sure the light is on. Sometimes the battery is so drained that only enough energy is needed to turn on the backlight, but not to start the system.
If the smartphone is stuck on the logo again after a forced restart, the problem goes deeper, requiring a switch to more serious diagnostic methods, such as entering Recovery Recovery mode.
Using Recovery Mode to Reset Settings
Recovery mode is a separate software partition that allows you to manage the system without fully booting it, and this is where we can reset to factory settings, which often eliminates update conflicts or corrupted files.
To enter this mode, turn off the phone completely (if it freezes, wait for the discharge or use a forced reboot and immediately press the buttons). On the device turned off, press the Power button and Volume up simultaneously. Hold them until the Mi logo appears, then release them.
What happens if the Recovery does not open?
In the menu, you can navigate with volume buttons and choose with the power button. You need to find the Wipe Data item, and inside that, select Wipe All Data and confirm the action.
☑️ Checklist before reset
Once the cleanup process is complete, select Reboot and then Reboot to System. The first run can take up to 5-10 minutes as the system will reassemble its files.
Enter Fastboot and Diagnostics via PC
If the Recovery reset didn't help, or you can't get into it, Fastboot mode comes to the rescue. It's a low-level protocol that allows the computer to interact with the phone's bootloader. In this mode, a hare is usually shown on the screen fixing an android.
To get to Fastboot, on the device turned off, press the Power button and Volume down. Connect the phone to the computer through high-quality USB-You need to install drivers on your PC. ADB and the Mi Flash Tool utility or use the command line.
Checking the connection in Fastboot mode allows you to know if the processor and memory controller are alive. Open the command prompt in Windows (cmd) and type in the command:
fastboot devicesIf you see the serial number of the device, it means that the connection to the hardware is there, and the problem is probably software. USB-port.
| Regime. | Button combination | Screen indication | Appointment |
|---|---|---|---|
| Recovery | Food + Volume Up | Menu with text (Mi-Recovery) | Data reset, update |
| Fastboot | Food + Volume Down | The android hare | Firmware, unlock. |
| Edl (9008) | Special combination or test points | Black screen | Rescue of the Bricks |
Complete flashing of the device through Mi Flash
When simple methods are exhausted, you have heavy artillery, full firmware, and you need a computer, a stable Internet, and original firmware for your particular model, and you can find it on the official website miui.com.
It is important to download the firmware specifically for Fastboot mode (the file has the extension.tgz, not.zip). Unpack the archive to the root of the C disk so that the path is short, for example: C:/mi_rom/. Long paths with Cyrillic can cause error.
⚠️ Note: When you run the firmware with the Clear All option, all data will be permanently deleted. Make sure you have a backup of important contacts and photos in the cloud.
Run the Mi Flash Tool on behalf of the administrator. Connect your phone in Fastboot mode. Press the Refresh button and the program must identify the device. Choose the path to the firmware folder and click Flash.
💡
The choice of firmware type is critical: the “Clean All” option cleans the phone completely, and “Save User Data” tries to save files, but may not solve the problem if it is in the user’s data.
It takes 200 to 600 seconds. Under no circumstances, turn off the cable or touch the phone at this time. Once completed, the device will automatically restart.
Hardware causes and problem of the display plume
If the Xiaomi phone is turned on, you hear the boot sound, the vibration is working, but the screen remains black or shows a ripple, the display plume may have gone.
A common cause is also sticking buttons. If the volume or power button is physically stuck in the pressed state (due to dirt, moisture or impact), the phone will constantly try to enter Recovery or Fastboot mode, creating the illusion of endless boot.
Try to carefully “develop” the buttons by repeatedly pressing them. If this does not help, you will need to disassemble the device to check the connectors and clean the board of dust or oxides.
💡
Try to press the top of the screen or the back cover slightly in the camera area during the turn on, and if the phone suddenly boots up, then the problem is poor contact of the plume or board.
EDL mode and service access
In the most severe cases, when the phone does not respond to any buttons and is not detected in the Fastboot, the EDL (Emergency Download) mode remains, and logging into it often requires disassembling the phone and closing special contacts (Test Points) on the motherboard.
This mode allows you to reflash the device even with a damaged bootloader, but its use usually requires authorized Xiaomi accounts, which are only available to employees of service centers.
If you have reached this stage and do not have experience in soldering and working with electronics, further independent actions can lead to the final failure of the device.
⚠️ Warning: Attempting to self-close contacts without a circuit can short-circuit and burn the processor.
In such a situation, it is more rational to consult professionals, they will be able to diagnose a memory malfunction (eMMC/UFS) or processor, which is often the cause of “perpetual load” on older models.