Xiaomi phone does not turn on: step-by-step recovery instructions

You press the power button, but Xiaomi's screen stays black, or the device vibrates but doesn't load beyond the logo. MI. The situation is familiar to many owners of smartphones brand — from budget Redmi to flagship Xiaomi 13. the reasons can be different: from a discharged battery to serious hardware breakdowns.

In this article, we'll look at all the possible scenarios where Xiaomi's phone refuses to turn on, and we'll offer proven solutions, from basic to advanced. Importantly, some techniques require technical skills, so if you're not sure about your abilities, you'd better go to the service center, but in 70% of cases, you can fix the problem yourself.

1. Checking for obvious causes: charging and physical damage

Before you panic, rule out the simplest of reasons. Most often, Xiaomi's phone won't turn on because of a trivial battery discharge or cable issues.

• 🔌 Connect the original charging cable and power supply (don’t use cheap analogues!) Leave on charging for at least 30 minutes – sometimes a discharged battery takes time to “wake up".
• 🔋 Try another charger or USB-If the phone shows a charging indicator (red/orange LED) but does not turn on, the problem may be a software failure.
• 🔍 Check the connector. USB-C (Or micro-USB in older models, for dirt, oxidation, or physical damage, clean it carefully with a toothpick or compressed air.
• 💧 Check if there was contact with moisture.Even if the phone didn't fall into the water, high humidity or condensation can cause corrosion on the board.

If the phone vibrates after charging, but the screen remains black, this may indicate a malfunction of the display or plume, in which case, try connecting the device to the computer - if the PC recognizes it, the problem is exactly in the screen.

⚠️ Note: Do not use "fast charging" from other brands (such as Samsung or OnePlus) for Xiaomi phones. Different manufacturers use different protocols, which can lead to overheating or damage to the power controller.

Falls or impacts|System updates|Charging.|By itself (without apparent reason)|The other.-->

Forced reset: how to get out of the “freeze”

If Xiaomi phone is stuck on the logo MI, If you have a black screen or a cyclical reset, hard reset will help, and this method doesn't delete data, it just restarts the system:

• 📱 For most modern models (Redmi Note) 10/11/12, Xiaomi 12/13, POCO F4/F5): Press the power button. + Volume up on 10–15 seconds until the phone vibrates and restarts.
• 📱 For older models (Redmi) 4/5, Mi A1/A2): nutrition + Loudness down.
• 📱 For non-removable battery devices (e.g. Mi 9, Mi 10): If the phone doesn’t respond to buttons, plug it into charging and hold the power. + Loudness up for 20-30 seconds.

If the phone is turned on after a forced reboot but is not stable (brakes, spontaneously shuts down), this may indicate damage to system files, in which case the reset to factory settings or flashing will help.

Try a different key combination (Nutrition) + Volume up/down)|Connect to charging and try again|Leave on charging for 1-2 hours|Try connecting to a PC for diagnostics-->

If a hard reset didn’t help and the phone still doesn’t turn on, move on to the next step – checking the battery and diagnosing through the computer.

3.Diagnostics via PC: determine whether the phone is alive

If the screen is still black, but the phone is making sounds or vibrating when you connect to the charger, you can try to wake it up through the computer.

• 🖥️ Computer with installed Xiaomi drivers (you can download on the official website).
• 🔌 Original. USB-cable (better than the one that came with the kit).
• 🛠️ Mi Flash Tool (for firmware) or ADB Tools (for diagnostics).

Connect your phone to your PC and do the following:

1. Open Device Manager on your computer (click Win) + X → Device Manager).
2. Check if the Qualcomm device appears on the list HS-USB QDLoader 9008 or MediaTek Preloader. If so, the phone will be recognized in emergency mode (EDL), and it can be stitched.
3. If the device is not detected, try holding the Volume button down when connecting to a PC – this sometimes helps put the phone into Fastboot mode.

If the computer doesn't recognize the phone at all, it could indicate a motherboard failure or battery contacts collapse, and then you can't do without disassembling the device.

4. Phone firmware: when resetting doesn't help

If Xiaomi's phone turns on but hangs on the logo, reboots cyclically, or gives out a Fastboot error, flashing it will help. This is an extreme measure that deletes all the data, but brings the device back to life.

Method 1: Fastboot firmware (if the phone is determined by the PC)

Suitable for most models Xiaomi/Redmi/POCO. Procedures for action:

1. Download the official firmware for your model from the Xiaomi Firmware website (choose the Fastboot version).
2. Unpack the archive in a folder on your computer.
3. Install the Mi Flash Tool and run it on behalf of the administrator.
4. Connect the phone in Fastboot mode (clip Power + Volume down when turned on).
5. In the program, select the firmware folder and press Refresh → Flash.

Method 2: Firmware through EDL (if the phone is in the brick")

If the phone is unresponsive and is identified as QDLoader 9008, you will need to:

• 🔧 Mi Flash Pro or QFil (for Qualcomm chips).
• 📄 Firmware in.mbn or.elf format (see forums) 4PDA or XDA-Developers).
• 🔑 Authorized Mi Account (new models require unlocking the bootloader).

⚠️ Attention: Firmware through EDL On new Xiaomi models (released after 2021) you need to log in, and without it, the phone will lock permanently.

On Xiaomi models 12/13 Redmi Note 11/12 Firmware through informal tools (e.g. China Flash Tool) can lead to blocking IMEI. Recovering it later will be extremely difficult.

💡

Before the firmware check the phone model by IMEI (Installing firmware from another model will turn the device into a brick".

5. Battery problems: When charging doesn't help

If the Xiaomi phone doesn't show signs of life even after a long charge, the problem could be in the battery.

• 🔋 The phone is turned on only when the cable is connected, but immediately switches off when disconnected.
• 🔥 The battery swelled (see on the raised screen or body).
• 📉 Charge drops from 100% to 0% in a few minutes.

In such cases, only a battery replacement will help. 8/9/10 Xiaomi Mi 10/11 You can do it yourself, if you have experience disassembling the equipment:

• 🛠️ Plastic mediator or guitar mediator for opening the body.
• 🔧 Cross screwdriver (usually) PH00).
• 🔋 New battery (buy only the original or certified analogues from Baseus, Remax).
• 🧲 Screen removal suction cup (optional).

If you've never disassembled a phone, you should contact the service. A bloated battery is dangerous - it can ignite if you carelessly handle it. The average cost of replacing a service is 1,500-3,000 rubles (depending on the model).

💡

If the phone doesn't turn on after a fall, don't try to charge it! This can short circuit. First check the integrity of the battery and board.

6. Hardware breakdowns: when you need the help of a specialist

If all the software methods have been tried and the Xiaomi phone still doesn't turn on, the problem is the hardware.

Some breakdowns can be diagnosed independently:

• 🔍 Short circuit check: connect your phone to charge and touch the case. If it heats up quickly in one place (usually near a connector or camera), it's a sign of CZ.
• 🎧 Sound check: When connected to charging, the phone must emit a characteristic sound (if Charging Sounds were previously enabled.
• 🔦 Backlight check: light a flashlight on a screen in a dark room. If you see a dim image, the problem is the backlight or the plume.

If the Xiaomi phone fell into the water or was subjected to a strong vibration (for example, after a fall), there is a risk of chip failure. BGA-chips, which is possible only in specialized services with a soldering station.

7.When repairs are impractical: is it worth fixing the old Xiaomi

If your phone XiaomiReleased a few years ago (e.g. Redmi) 4X, Mi A1, Mi 8, repairs can cost more than the device itself. Here are the guidelines for when to buy a new smartphone:

• 💰 The cost of repairs exceeds 50% of the price of a new phone in the same segment.
• 🔋 Battery is worn out by more than 80% (checked by AccuBattery or by the battery). AIDA64).
• 🛠️ Replacement of the motherboard is required (this is usually 70-90% of the cost of the device).
• 📱 Models older than 4-5 years and do not receive security updates.

For comparison, the average prices for repairs of popular Xiaomi models in 2026:

• Redmi Note 10/11: screen-replacement — 3 000–4 500 rub., battery — 1 200–1 800 ruble.
• Xiaomi 11T/12: display-replacement — 5 000–7 000 RUB, repair of payment - from 8 000 ruble.
• POCO F3/F4: charge-plate — 1 500–2 500 rupee, soldering of the power chip — 6 000–10 000 ruble.

If you're buying a new phone, you can try to save the data from the old phone.

1. Remove the memory card (if it was installed).
2. If the phone is sometimes turned on, connect it to your PC and copy files through MTP.
3. In extreme cases, contact the service - some workshops offer services for extracting data from damaged devices (cost: 2 000-5 000 rubles).

8 Prevention: How to avoid problems in the future

To ensure that your Xiaomi lasts longer and doesn’t face inclusion issues, follow these guidelines:

• 🔋 Battery: Avoid full discharge (charge at 15-20%) and overheating (do not leave in the sun or near heat sources%.
• 🔄 Updates: Only install official firmware through Settings → The phone. → Update the system. Avoid customization. ROM, if you don't know them.
• 💧 Moisture: Even if your model has protection IP53 (For example, Redmi Note 12, avoid direct contact with water. Once moisture is in, turn off your phone immediately and dry it in rice or silica gel for 24 to 48 hours.
• 🛡️ Protection: use a cover and protective glass, falling from a height of 1 meter on a hard surface can damage the motherboard.
• 🔌 Charging: do not use cheap cables and power supplies, the best option is the original RAM or certified accessories (for example, from Baseus or Anker).

If the phone starts to spontaneously turn off or overheat, this is the first signal of future problems.

1. Check the battery wear in Settings → Battery status.
2. Run a performance test in AIDA64 or CPU Throttling Test.
3. Clean your phone from garbage with Mi Cleaner or SD Maid.

💡

Regularly (every 3-6 months) reset your cache through Recovery, which prevents the accumulation of system errors that can lead to failures when turned on.

FAQ: Frequent questions about Xiaomi phones not included