How to Open the Xiaomi Redmi 4A Cover: The Complete Guide

Xiaomi Redmi 4A has become one of the most popular budget devices of its time, but over time, even the most reliable equipment requires maintenance. Often users are faced with the need to replace a failed battery or broken glass display, and the first step in this process is to dismantle the rear panel. Unlike modern monoblocks, this model has a removable cover, which theoretically simplifies access to the insides, but in practice requires a certain skill and caution.

Improper handling of the case can lead to cracks in the plastic or damage to the plumes, so it is important to clearly understand the sequence of actions before starting work. In this article, we will discuss in detail how to open the cover Xiaomi Redmi 4A, what tools you need and what nuances you should pay special attention to so as not to turn a minor repair into a new phone.

Workplace preparation and necessary tools

Before you start disassembling, you need to have a comfortable workspace with good lighting, you need a clean, flat surface covered with soft material, so that small screws do not get lost and parts do not get scratched, and the lack of dust and static electricity will also play an important role in the safety of the electronics of the device.

To successfully complete the task of removing the lid, you will need a minimum set of tools that can be found at home or purchased at any electronics store, the main tool will be a plastic blade or a mediator that will allow you to tamper with the case without risking damage.

• 🔧 Plastic blade (spooger) or mediator for opening latches.
• 🔧 Thin metal spatula (use with extreme caution).
• 🔧 Suction cup for lifting the cover (optional, but convenient).
• 🔧 Phillips screwdriver for screws under the battery.

The use of metal objects such as knives or needles is not recommended, as they can easily break through the battery or damage the plumes.If there is no professional spooger at hand, it is better to use a plastic card pre-harvested in the corner than risk the integrity of the gadget.

Analysis of the design of the Redmi 4A

The Redmi 4A is made of matte plastic, which, despite its strength, is sensitive to spot impacts and curves. The back is held not only by screws under a plug, but also by a system of internal latches around the perimeter of the device. Understanding where these latches are located is critical to preventing breakage.

Unlike more expensive models, there are no additional screws on the sides, which simplifies the process, but requires accuracy when snapping. Plastic becomes more fragile over time, especially if the phone has often been subjected to temperature changes, so you need to act smoothly and without sharp jerks.

Notice the joints of the body: it's the gap between the main frame and the back cover that you need to insert the tool, and the micro gaps are visible to the naked eye when you look at the sidelight.

Step-by-step: how to remove the back cover

The first step is to extract SIM-This is a mandatory procedure, because the presence of a tray creates stress in the structure and can lead to a breakdown of the mechanism when you try to open the lid.

Then you flip the smartphone down and find a rectangular plug at the bottom of the back, and underneath it, you have two screws that hold the bottom of the lid, and you need to carefully twist them out with a cross screwdriver of the right size and put them away in a safe place.

Now you can start the process of snapping, insert the plastic blade into the gap between the frame and the lid in the lower corner, where the screws were previously, and with a slight push, swipe the tool along the side face, hearing the characteristic clicks of the locks opening.

Move around the perimeter of the device, sequentially releasing the latches. Don't try to bend the lid immediately after opening one corner, it can break the plastic. Walk the tool around the circuit until the panel begins to detach freely.

⚠️ Warning: Do not use force if the lid fails. Check if all screws are twisted and if the tool is stuck somewhere. Excessive effort will lead to white clatters on the plastic.

Work with the battery and internal components

After successfully removing the back cover, the smartphone’s internal device will open to your eyes. In the Xiaomi Redmi 4A, the battery takes up a significant part of the space and is closed with an additional plastic lining, which is also fixed by screws.

To access the plumes and the battery itself, you need to unscrew the screws located under the plastic lining at the bottom of the device (usually 10 pieces, but the number can be cooked).

• 🔋 Carefully disconnect the battery plume from the motherboard.
• 🔋 Check the condition of the contact site for oxidation.
• 🔋 If the battery is swelling, do not press on it with sharp objects.

The adhesive base on which the battery is held loses its properties over time, but in rare cases it can hold firmly. To extract the battery, you can use a suction cup or gently tuck it with a plastic card from the end.

If your goal was to replace the screen, you need to remove the metal frame that covers the display plumes after the battery is turned off, which is usually attached with several screws and plastic latches.

Typical mistakes when disassembling a smartphone

One of the most common mistakes is ignoring the screws under a plug, and many users try to force the lid off, forgetting that the two screws are still holding the structure, which leads to the breaking of the plastic mounting poles.

Another mistake is to use a tool that is too thick, so the blade should not go deeper than 2-3 millimeters into the gap, and a deep dive will ensure that the plumes are cut or the side buttons are damaged.

It is also common to forget to turn off the battery before working with other components, and touching the contacts under tension with tweezers can short-circuit and disable the motherboard.

Take your time and pull the lid. Plastic is a viscous material, and a sharp jerk can lead to unpredictable results. It is better to spend an extra minute warming up with a hair dryer (if the glue is old) or more thoroughly passing the perimeter with a spatula.

Comparison of opening methods of the body

There are several approaches to removing the back panel, and the choice of method depends on the condition of your device and the tools available. Below is a table comparing the effectiveness and risks of the different methods.

The safest and most recommended method is to use a plastic blade in combination with manual snapping, which gives you complete control over the process and minimizes the risk of accidental damage.

Using a suction cup is effective only if the lid sits tightly and there is no risk of damaging the side elements.Metal tools should only be used by experienced craftsmen in extreme cases.

Assembly and performance check

After the necessary repairs (replacing the battery, screen or cleaning the speaker) are done, the assembly phase is as careful as disassembly, and first of all, make sure that all the plumes are tightly seated in their connectors and are fixed with clamping slats.

Put the battery back in place and plug it into the motherboard. Don't put the lid in right away -- first check if the phone is turning on and if the touchscreen is working, and that saves time in case you forget to plug in some connector.

💡

Before final assembly, wipe the inside of the lid and the smartphone frame with an alcohol napkin – this will remove dust and prints that can be seen through the translucent plastic.

When you set the lid, first snap one of the top corners, then walk around the perimeter, pressing your thumbs. A characteristic click will tell you that the lock is in place. SIM-tray.

The final test involves testing all the buttons, vibrations, sound and communication modules, and if everything works correctly, it can be considered a success.

Concluding recommendations

Repairing electronics with your own hands is a useful skill that saves money and extends the life of your favorite gadgets, but it is important to be aware of the limits of your abilities. If you feel insecure or faced with unforeseen difficulties, you better turn to professionals.

Xiaomi Redmi 4A is a friendly device for beginners, but it requires respect. Safety and accuracy are the main keys to success.

💡

The main secret of success is to take your time and feel the resistance of plastic so as not to break the latches.

⚠️ Warning: If the phone doesn't turn on after assembly, don't try to charge it intensely. Take it apart again and check for battery plume connection and no foreign objects on the board.

Remember that cleaning the connectors regularly and using protective covers can delay the need to open the case for many years.