How to carefully remove the back cover Xiaomi Redmi 7A: instructions with photos and videos

Xiaomi Redmi 7A is one of the most popular budget smartphones of the brand, but even such a reliable device can eventually experience problems, from a discharged battery to a damaged charging connector. Many users face the need to disassemble the device to replace parts or clean from dust, but are afraid to damage the fragile back cover. In this article, we will discuss how to properly remove the rear panel of the Redmi 7A without the risk of breaking latches or damaging the plumes, and also talk about the nuances that are not covered in standard instructions.

It's important to understand that the Redmi 7A's back cover is not only attached to the latches, but also to the adhesive layer, which makes it difficult to dismantle, and that there are delicate elements inside, from the battery to the antenna modules, that are easily damaged if you carelessly handle them. If you've never taken a smartphone apart before, we recommend that you first familiarize yourself with the theoretical part to avoid typical errors.

Preparation for disassembly: tools and security measures

Before you start removing the lid, you need to prepare the workspace and tools, and using the wrong tools (knives, screwdrivers, the wrong size) can cause plastic to chip or damage to the internal components.

• 📦 Container for screws (in Redmi) 7A different sizes of screws are used).

Also, prepare a soft fabric without a pile (microfibre) to put your smartphone on it and avoid scratches. Work on a flat, well-lit surface - better cover the table with white paper so as not to lose small details.

⚠️ Attention! Do not use a household hair dryer at maximum power, it can melt the plastic of the lid. Optimal distance to the body: 10-15 cm, temperature - up to 60°C. When overheating, the glue may not peel off, but, on the contrary, harden.

How to remove the back cover of Redmi 7A

Now, let's get to the process itself, follow the instructions strictly in steps to minimize the risks:

1. Turn off your smartphone and remove it. SIM-This will prevent short circuits from accidentally coming into contact with the board.
2. Heat the edges of the lid with a hair dryer for 1-2 minutes, evenly driving around the perimeter. Pay special attention to the corners - there is a thicker adhesive layer.
3. With a suction cup, lift the lid from the bottom edge (on the side of the charging connector). If there is no suction cup, gently apply the mediator, starting at the corner.
4. Keep the lid apart, gradually moving the mediator along the body. Don't try to rip it off abruptly, so you break the latches!
5. Put the lid aside and clean the inside of the adhesive with alcohol. Don't use acetone, it's corroding the plastic!

If the lid doesn't lend itself, don't use excessive force -- 90 percent of the time, the problem is not properly heated glue. Reheat again, focusing on the problem areas.

Is the smartphone off?|Whether extracted SIM-memory-card?|Whether the tools (mediator, sucker, alcohol) are prepared)?|Whether the edges of the lid are heated by a hairdryer?|Is there a container for screws and small parts?-->

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when disassembling the Redmi 7A. Here are the most common ones and ways to prevent them:

• 🔨 Use of metal tools → Solution: buy a plastic mediator or use a guitar mediator.
• 🔥 Overheating of the lid → Plastic is deforming, glue is hardening. Solution: heat no more than 2 minutes intermittently.
• 💥 Sharp compartment of the lid → Solution: Move the mediator smoothly, without jerking.
• 🔋 Damage to battery plume → Solution: before you disassemble the battery, disconnect the battery.

Another common problem is the glue residue on the body that prevents the smartphone from being reassembled, so to remove it, moisten the cotton swab in isopropyl alcohol and gently wipe the surface. Do not use a knife or other sharp objects!

What is under the cover: the device Xiaomi Redmi 7A

After successfully removing the back panel, you will see the interior design of the smartphone, and here are the main components that you can replace yourself:

If your goal is to replace the battery, consider that the Redmi 7A has it glued to the body. Use a plastic blade to safely extract it and heat the battery with a hairdryer (but not above 50°C!).

💡

Before disconnecting the battery plume, take a picture of the location of the connectors on the motherboard, which will help avoid errors in the reverse assembly.

How to assemble a smartphone back: Assembly tips

Building the Redmi 7A after repair is as important as disassembling, and here are the key points to consider:

1. Check all the plumes – they should be tightly connected to the connectors on the motherboard.
2. Make sure the screws are twisted into the right holes. Redmi 7A uses screws of different lengths!
3. Apply a new adhesive layer on the lid (you can use bilateral tape or B-7000 glue).
4. Run a test turn on before the final cap fixation to make sure everything works.

If after the assembly of the smartphone does not turn on, check:

• 🔌 Is the battery connected (sometimes the plume leaves when the lid is installed).
• 📶 Are antenna modules damaged (network or Wi-Fi problems).
• 🔊 Is the speaker working (the connector may have moved away).

⚠️ Attention! If the smartphone overheats or runs out quickly after assembly, it's likely that the battery is not connected correctly or damaged.

💡

The most common build error is tug-of-war screws, which can cause cracks in the motherboard or damage to the connectors.

When is the best time to contact the service center

While disassembling the Redmi 7A seems simple, there are some cases where it’s best to entrust repairs to professionals:

• 🛠️ Damaged motherboard (requires rationing or diagnosis of chips).
• 📡 Problems with antennas (difficult to diagnose without special equipment).
• 🔋 The battery is raised (the risk of fire when self-replacement).
• 💧 Liquid got inside the case (urlex cleaning is necessary).

The cost of repairs at a Xiaomi service center or a verified workshop is usually:

• Replacement of the battery - 800-1500 rubles.
• Replacement of the speaker - 500-1000 rubles.
• Replacement of the back cover - 1000-2000 rubles (depending on color).
• Diagnosis of the fee - from 500 rubles.

If you’re unsure of your skills, don’t take the risk – modern smartphones have a complex design and one mistake can lead to expensive repairs.

Video instructions and additional resources

For clarity, we recommend to read the video analysis Redmi 7A. Here are the verified sources:

• 📺 YouTube channel "Repair World" - detailed analysis with comments in Russian.
• 📺 Xiaomi Service Channel – Official instructions from service centers.
• 📖 Forum 4PDA — redmi-repair 7A photoreported.

Before watching the video, note the date of publication – the design of the smartphone may have changed in various revisions, for example, in the early Redmi 7A games Torx T3 screws were used, and in the later ones – Phillips #00.

💡

If you are looking for parts for the Redmi 7A, buy them only from trusted sellers (for example, on AliExpress from official Xiaomi stores).

FAQ: Frequent questions about the Xiaomi Redmi 7A disassembly