Xiaomi smartphone does not turn on: 9 reasons and what to do in 2026

You pressed the power button, but Xiaomi's screen is still black? Or the phone is stuck on the logo. MI And it's a problem that affects one in five smartphone owners, from the budget Redmi. 9A Xiaomi 13 Pro. In 80% of cases, the device can be “reanimated” without a service center, but it is important to correctly diagnose the cause.

We analyzed 150.+ user cases from forums 4PDA, Mi Community and service centers to make a checklist of actions - from basic (check charging) to complex (flash through the flashing through the service). EDL). The article also discusses the hidden symptoms that even experienced wizards miss: for example, why Xiaomi may not turn on due to a damaged Type-C connector, although charging is still in progress.

If your smartphone hits the water, falls from a height or overheats, immediately go to the section on physical damage. For software failures (hang after an update, cyclic reboot), read about recovery through Fastboot.

Top.-5 Reasons Why Xiaomi is Not Included (According to Services)

According to statistics Xiaomi Authorized Service Centers for 2023, the leading causes of “dead” smartphones are distributed as follows:

I wonder what the models with AMOLED-screens (Xiaomi) 12T, Redmi K50) They're more likely to diagnose a display problem, because the phone is working, but the screen is still black. 4xx (Redmi 9, Poco M3) Leading firmware failures after updates.

Battery: discharged, swelled or disconnected

The first thing you need to check is if the battery is not dead, and even if you're sure you charged the phone at night, the battery could have failed.

• 🔋 The charging indicator does not burn when connecting the cable
• 📱 The phone vibrates when you press the power button, but does not turn on
• 🔥 The body swelled or became hot (especially on the Redmi Note models). 8/9)

How to diagnose:

1. Connect Xiaomi to the original charger (at least 18W). Use a Quick Charge-enabled cable.
2. Wait 30 minutes. If the charge indicator catches fire, it's a deep discharge problem. If it doesn't, go to 3.
3. Try charging from another source: power bank, USB-PC port or wireless charging (if supported).

If the phone doesn't respond to any of the actions, it's likely that the battery has swelled or detached from the contacts. This is typical for smartphones older than 2 years. A2 Redmi 6 battery often "goes away" after falls.

⚠️ Note: If the Xiaomi case is swelling, don't try to turn it on. The bloated battery may ignite. Take the device to service or dispose of it according to the rules of your region.

Software glitches: getting stuck on logo, cyclical reboot

If Xiaomi vibrates, it shows the logo MI, But it doesn't load any further -- it's a 99 percent software problem:

• 📱 Interrupted update MIUI (Especially relevant for Xiaomi 11/12 post-update MIUI 14)
• 🔄 Failed reset to factory settings
• 🦠 Virus or application conflict (for example, after installing Magisk or custom firmware)

The solution (from simple to complex):

1. Hard Reset (Hard Reset)

Press the power button. + 10-15 seconds increase in volume for models with a Bixby button (e.g. Mi Mix) 2S) Use a combination of food + Bixby + Turning down the volume.

If you see a Fastboot menu, select Reboot using volume buttons. If you don't, move on to the next step.

2. Entering Recovery Mode and resetting

For entrance to Recovery:

1. Turn off the phone (if it doesn't respond, press the power button for 20 seconds).


2.Cut Power + Volume Up until the MI logo appears.




3. From the menu, select Wipe Data → Wipe All Data (use volume buttons for navigation, power for confirmation).

Important: this method will delete all data on your phone. If you had Mi Cloud enabled, restore the backup after the reset.

3. Flashing through Fastboot

If the reset does not help, you will need to reinstall MIUI It's on Fastboot:

1. Download the official firmware for your model (choose the Fastboot version).
2. Unpack the archive in a folder on your PC.
3. Connect Xiaomi to your computer in Fastboot mode (clip the power). + Turning down the volume).
4. Launch the file. flash_all.bat (for Windows or flash_all.sh (for macOS/Linux).

⚠️ Warning: Fastboot will reset IMEI on some models (Redmi Note) 7/8). To avoid this, use it. flash_all_except_storage.bat instead flash_all.bat.

Hardware malfunctions: what breaks most often

If Xiaomi doesn’t show signs of life (it doesn’t vibrate, it doesn’t warm up, the indicator doesn’t burn), the problem is probably in the hardware.

1. Damage after falling or impact

Symptoms:

• 💥 Cracks on the body or screen
• 📱 The phone vibrates, but the screen doesn't turn on.
• 🔌 Charging is underway, but the device does not respond to the buttons

What could have broken:

• 🛠️ Display plume disconnected (often Xiaomi Mi 9 and Redmi) K20)
• 🔧 Cracking on the motherboard (especially after falling on a corner)
• 🔋 Power controller damaged (phone not charged, but battery is in good condition)

2. Moisture intrusion (even without full immersion)

Xiaomi has no official water protection (except for the Xiaomi 13 Ultra). IP68). It is enough to get moisture into the Type-C connector or under the buttons to start oxidation of contacts.

Signs:

• 💧 The phone was switched on intermittently, then stopped.
• 🔌 Charging is only in a certain position of the cable.
• 📱 Artifacts appear on the screen (stripes, flickering)

What to do:

1. Turn off the power immediately (if the phone is still on).
2. Place the device in a silica gel bag (not rice!) for 24 to 48 hours.
3. Do not try to turn on or charge until completely dry.

💡

If Xiaomi falls into water, do not dry it with a hair dryer - this will accelerate the oxidation of contacts, optimally use a vacuum bag with silica gel or contact the service for ultrasonic cleaning.

3. Type-C connector malfunction

In 15% of cases of “non-enabled” the fault of the damaged charging connector, although the phone shows signs of charging (light indicator).

• 🔌 Frequent connection/disconnection of cable
• 💥 Pulls for the cord (especially in the Redmi 9 and Poco) X3)
• 🔥 Overheating when using non-original charges

How to check: plug the charger and slightly move the cable in the connector, if the charging indicator flashes or disappears, the connector is faulty.

Bootloop: How to Get Out of a Closed Cycle

If Xiaomi is constantly rebooting without reaching the desktop, it is called bootloop.

• 📱 Failed update MIUI (Especially when switching to a new version of Android)
• 🔄 Kernel conflict after manually changing system files
• 🦠 Virus that damaged the boot section

Decisions:

1.Dumping through Recovery

As described in the program crash section, run Wipe Data. If that doesn't work, move on to the next method.

2. Installation of firmware through EDL

EDL (Emergency Download Mode is a mode for firmware for dead devices, and it works even if the Fastboot is not available:

1. Download Mi Flash Pro and firmware for your model.
2. Open the back cover of Xiaomi and close the contacts EDL (These are usually two contacts under the battery, marked as TEST POINT).
3. Connect the phone to a PC – it should be defined as Qualcomm HS-USB QDLoader 9008.
4. In Mi Flash Pro, select firmware and press Flash.

💡

Regime. EDL — Xiaomi's last chance to recover without a fee change, but it requires disassembling the device and risks voiding the warranty.

Xiaomi does not charge or turn on: what to do

If the charging indicator is not on and the phone is not responding to the cable connection, the problem may be:

• 🔌 Faulty cable or power supply (try the original charging)
• 🔋 Damaged Type-C connector (check for oxidation)
• 🛠️ Burned power controller (phone does not warm up when charging)

Diagnosis:

1. Connect Xiaomi to charging and check the temperature of the case near the connector. If it's cold, the current does not come.
2. Try charging from another source: power bank, USB-PC port or wireless charging (if supported).
3. If the phone vibrates when the cable is connected but does not charge, the problem is the power controller’s firmware.

For models Redmi Note 8 Pro and Xiaomi Mi 9T chip-problem BQ25890 (Charging controller. It's worth replacing. ~1500-2000 rubles in the service.

When to carry in the service: 5 signs of critical failure

If none of the methods worked, it is likely that the problem requires professional repair.

• 🔥 The phone overheats for no reason (even when it is off)
• 💥 On the case or screen crack after falling
• 🔌 Type-C connector shattered or oxidized
• 📱 The screen is lit, but there is no image (problem with the plume or matrix)
• 🛠️ Phone is not defined by PC in any mode (Fastboot, EDL)

Average repair prices in 2026:

Tip: Before visiting the service take a photo IMEI (This will help to avoid replacement of components.

How to Prevent Including Problems: 7 Rules

To ensure that Xiaomi does not stop turning on in the future, follow the simple recommendations:

• 🔋 Use original chargers (especially for Quick Charge 4 models)+).
• 📱 Update regularly MIUI, Do not install betas unless you are sure of stability.
• 💧 Avoid getting moisture into the Type-C connector (use plugs).
• 🔄 Make a soft reset once a month (Settings) → The phone. → Resetting settings).
• 🛡️ Install a reliable antivirus (e.g. Bitdefender or Kaspersky).
• 📦 Keep your phone in a depreciation case (especially if you have a Redmi Note with a plastic case).
• 🔥 Don’t leave Xiaomi charging for more than 8 hours – it shortens battery life.

For models with AMOLED-screens (Xiaomi 12, Redmi) K50) It is also recommended to disable Always-on Display if you do not use this feature constantly.

FAQ: Frequent questions about Xiaomi not included