How to install NFC-Module on the phone Xiaomi: a complete guide with photos and tips

Introduction: Why to Install NFC Xiaomi and what it takes

Module NFC (Near Field Communication has become an integral part of modern smartphones, allowing you to quickly pay for purchases, share data and manage smart devices. POCO — If your phone doesn't support contactless technology, there's a solution: NFC-module.

The process requires accuracy and basic electronics skills, but with the right approach, even a beginner can cope in 1-2 hours. In this article, we will analyze all the nuances of choosing a module, disassembling the case, soldering contacts and setting up software - taking into account the features of different Xiaomi series (from Redmi Note 10 to Mi 11).

What Xiaomi models support installation NFC-module

Not all Xiaomi smartphones can be equipped with NFC — It depends on the motherboard design and the availability of free connectors:

If your model is not on the list, check for a free slot for the module on the motherboard.

1. Remove the back cover (carefully so as not to damage the plumes!).
2. Find a metal plaza with an inscription NFC or RFID near-battery.
3. Check if there are contacts to connect the antenna (usually 4-6 spring connectors).

⚠️ Attention: On models POCO M3 redmi 8A installation NFC It is technically possible, but requires a complete replacement of the motherboard with a support version (for example, with the Redmi Note 8 Pro.

Choice NFC-Module: what to buy and where to look

Three components will be needed for installation:

• 📱 NFC-module + antenna, the main element. Popular models: NXP PN547, PN80T, SN100T.
• 🔧 Flexible plume - connects the module to the motherboard. length 5-10 cm.
• 🛠️ Double-sided tape or glue - to fix the antenna under the cover.

Where to buy:

• 🌍 AliExpress is the biggest choice, but a long wait (2-4 weeks: "NFC module for Xiaomi Redmi Note 10" or "PN547 for POCO X3".
• 🏬 Local radio parts stores are faster but more expensive.
• 🔄 B/U markets (Avito, OLX) — You can find modules from disassembled phones (for example, with Samsung Galaxy or Huawei).

Cost of the kit: from 500 to 2000 rubles, depending on the model of the chip and the seller. Pay attention to reviews - often Chinese modules come without an antenna or with damaged contacts.

💡

Before buying, check if your Android version supports external devices. NFC-On some firmware (e.g., on some firmware, MIUI 12.5 and below) manual addition of drivers may be required.

Step-by-step instruction: installation NFC-module

To work, you will need the tools:

• ✅ Screwdriver. T3 and T5 (Xiaomi screws).
• ✅ Plastic mediator or guitar string – to open the lid.
• ✅ soldering iron (power 20-30 W) with a thin sting.
• ✅ solder and flux (better to use acid-free).
• ✅ Multimeter – to check contacts.

Step 1: Disassembling the phone

1. Turn off the phone and remove it. SIM-map.
2. Heat the back cover with a hair dryer (temperature 60–70)°C. This will soften the glue.
3. Carefully tuck the cover with the mediator, starting at the corner next to the volume button.
4. Unscrew all the screws of the motherboard (usually 8-12 pieces).

Step 2: Connecting the module

1. Find contact points on the board for NFC (See the photo for your model below).
2. Seal the module plume to the contacts. Circuit: 1. VCC (3.3V) 2. GND 3. SCL (tacting) 4. SDA (data) 5. IRQ (interruption)
3. Fix the antenna on the inside of the cover with double-sided tape.

Step 3: Assembly and inspection

1. Make sure the plume is not stretched or twisted.
2. Close the lid and twist the screws.
3. Turn on your phone and check the work. NFC customized.

⚠️ Attention: On models POCO X3 NFC And Redmi Note 10 Pro, after installing the module, the Wi-Fi signal may disappear. NFC Or move it closer to the top of the body.

Setup of the software after installation

Even if the module is physically connected, the system may not recognize it.

1. Verification in Engineering Mode

Go to the engineering menu by typing in the phone keyboard: ##4636## → Phone information → NFC.

If the partition is missing, the driver is not loaded.

Installation of drivers

• 📱 Download the Custom Core with Support NFC for your model (for example, NFC Enabler for Redmi Note 10).
• 🔧 Set it through TWRP Recovery (root rights required).
• 🔄 Reboot the phone.

3. Setup in MIUI

Go to Settings. → Connections → NFC and turn on the option:

1. Update MIUI to the latest version.
2. Reset network settings (Settings) → The phone. → Resetting settings).
3. Install the app NFC Tools from Google Play for testing.

Common Mistakes and How to Avoid Them

Even experienced professionals face problems with installation. NFC. Here are the most frequent of them:

Another common problem is the loss of warranty. Xiaomi does not officially support self-installation. NFC, So if you go to a service center, you may not be able to get repairs!

Alternative ways to add NFC Xiaomi

If soldering seems too difficult, consider these options:

1.External NFC-adapter

Devices like Sonoff. NFC or ACR122U plug in USB-C Or Bluetooth and emulate the work of the built-in module:

• 🔌 You need to carry an adapter with you.
• 🔋 Fast discharge of battery.
• 🚫 Not all apps (like Google Pay) work with external adapters.

2. Replacement of motherboard

For example, you can buy a fee from the Redmi Note 10 Pro (c) NFC) And you can put it in the Redmi Note 10, which is a radical method, but it's 100 percent workable, and it costs between 3,000 and 8,000 rubles.

3.Use of NFC-sticker

Buy programmable stickers (for example, NTAG213) And stick them on the back, and they're not going to replace a full module, but they're going to allow you to do that:

• 💳 To save bank card data (through NFC Tools).
• 🔑 Automate tasks (e.g., turn on Wi-Fi when touching).
• 📱 Transmitting contacts or links.

💡

The most reliable way is to install the original soldered module, external adapters and stickers are only suitable for limited tasks (for example, automation or data storage).

FAQ: Answers to Frequent Questions