Xiaomi Redmi Go is not loaded: a full analysis of the causes and solutions

Xiaomi Redmi Go is a budget smartphone based on Android Go Edition, which, despite its modest specs, has gained popularity due to its reliability. But even such devices sometimes refuse to turn on, leaving users confused. If your Redmi Go does not respond to the power button, hovers on the logo or cyclically reboots, do not rush to carry it to the service. In 80% of cases, the problem can be solved by yourself.

In this article, we’ll look at all the possible reasons why your phone doesn’t boot, from a simple battery drain to serious hardware failures, and give you step-by-step instructions with photos, video examples, and cautions to avoid typical errors, and if the problem is more difficult, you’ll learn how to diagnose a breakdown and when to contact a specialist.

1. Diagnosis of the problem: why is Redmi Go not included?

Before you start repairing, it is important to understand what exactly you are facing, and the symptoms of "non-boot" can be different, and each of them indicates its cause:

• 🔋 No reaction to the power button -- the phone is completely dead, it doesn't vibrate, it doesn't light up, it's usually the battery or the power supply.
• 🔄 Cyclical reboot – the device turns on, the Xiaomi logo appears, then the screen goes out and the process repeats.
• 📱 Logo getting stuck -- the phone turns on, but it doesn't go beyond the Redmi screensaver, and it could be a software glitch or a memory problem.
• 🔌 It only reacts to charging, and when you connect the cable, you get a charging indicator, but then the phone doesn't load.

If you don't get into either of these situations -- for example, the phone turns on but the screen stays black -- the problem could be the plume of the display or the graphics chip, and then you can't do without disassembling the device.

2.The first steps: what to do if the phone does not turn on?

Start with the simplest of things. Often users miss the obvious and immediately try to sew the device or bring it to the service.

Checking of charging and battery

Even if you're sure the phone was charged, the first thing you do is plug it into a 15 to 20 minute charger. Use the original Xiaomi cable and power supply -- cheap ones might not be producing enough current.

• 🔌 If the charging indicator doesn't light up, try another cable, socket or power bank.
• 🔋 If the light flashes red, the battery is completely drained. Wait at least 30 minutes before you try to turn it on.
• 🔥 If the phone gets hot when charging, it could indicate a battery or power controller malfunction!

Critical: If the Redmi Go doesn’t respond to charging for more than a day, never leave it plugged in for long – it could cause the battery to bloat.

Forced resetting

If the phone is stuck on the logo or reboots cyclically, try a hard reset.

1. Hold the Power + Volume button at the same time for 10-15 seconds.
2. When the phone vibrates or the screen goes out, release the buttons.
3. Wait 1-2 minutes and try to turn the device on in the usual way.

If the phone boots up after that, the problem was a temporary system failure. If it doesn't, move on to the next step.

Try another cable and charger |

Hold the power button for 20+ seconds for forced reboot |

Wait 30 minutes on charging, even if the indicator is not lit|

Try to turn on the phone without SIM-memory-cards

-->

3. Software glitches: Recovery through Recovery and Fastboot

If the phone responds to buttons but doesn't load beyond the logo, the problem is probably a damaged firmware or system file conflict, in which case a factory reset or firmware reflash will help.

3.1 Reset via Recovery Mode

Recovery menu allows you to reset your settings without connecting to a PC.

1. Turn off the phone (if it is on, hold the power button until it is turned off).
2. Press Power + Volume Up and hold until the Mi logo appears.
3. Release the buttons and you will see a menu in English or Chinese.

In the Recovery menu, you can control the volume buttons (up/down) and the power button (select). Select Wipe Data (or Clear Data), then confirm the action. After the reset, the phone should boot up in its original state.

⚠️ Warning: Recovery removes all data on your phone, including photos, contacts and apps. If you didn't have a backup, it's going to be extremely difficult to recover the information.

3.2 Flashing through Fastboot

If the reset didn't work, you'd have to go through the phone, USB-cable and official firmware for Redmi Go (codename tiare) can be downloaded on the Xiaomi Firmware website.

Instructions for firmware via Fastboot:

1. Install ADB and Fastboot Tools on PC.
2. Unpack the downloaded firmware in the folder with fastboot tools.
3. Turn off your phone and press Power + Volume Down to enter Fastboot mode.
4. Connect your phone to your PC and execute: fastboot flash all (this will automatically stitch all partitions).

It takes 5 to 10 minutes. When it's done, it'll restart. If the firmware is successful, but the phone still doesn't turn on, it could be the hardware.

4. Hardware breakdowns: when without repairs can not do

If all software methods have been tried, but Redmi Go still doesn't turn on, the problem is probably hardware.

The most common breakdowns faced by owners of Redmi Go:

• 🔋 Bloated battery - if the phone case is deformed, the battery needs to be replaced urgently!
• 🔌 Contact oxidation -- if the phone was in high humidity, the contacts on the board could oxidize.
• 🔧 Chip dump - when falls or impacts, the board elements (for example, the charging controller) may move away.

If you do not have experience in electronic repair, it is not recommended to disassemble the phone yourself.

💡

Before visiting the service, take a picture of the IMEI phone (under the battery or on the box).

5. Frequent user errors: what can not be done?

When trying to revive Redmi Go, many people do things that only make the problem worse.

• 🔥 Heating your phone (dryer, battery, microwave) – this can damage the board and battery.
• ⚡ Connect to unstable power sources (e.g., to USB-Use only the original charger.
• 🔧 Disassemble the phone without tools - plastic latches of the case are easy to break, after which the tightness will be broken.
• 💾 Install unofficial firmware – Redmi Go has limited memory, and “custom” firmware can finally put it out of action.

It is especially dangerous to solder the board without experience, and the wrong temperature of the soldering iron or the use of an active flux can lead to irreversible damage to the chips.

⚠️ Warning: If the phone is in water, don't turn it on, even if it's externally dry! Immediately remove the battery (if possible) and take the device to the service. corrosion on the board can manifest itself in a few days and disable the phone.

Prevention: How to avoid problems in the future?

To Xiaomi Redmi Go lasted longer and did not let you down at the most inopportune moment, follow these recommendations:

• 🔋 Don't drain the battery to zero -- try to plug in charging at 15-20 percent. Full discharge reduces battery life.
• 📱 Regularly reboot the phone – this clears the RAM and prevents freezes.
• 🔄 Don’t interrupt system updates – if your phone is updated, wait until the process is complete (usually 10-20 minutes).
• 🛡️ Install apps only from Google Play – third-party APK They may contain viruses that damage the system.

Avoid extreme temperatures: Do not leave your phone in the sun or near heaters, and the optimal range for the Redmi Go is from +5° to +35°C.

💡

If the phone is slowing down or rebooting spontaneously, these are the first signs of future problems. Don't ignore them: back up your data and take action (resetting, trash cleaning).

FAQ: Answers to Frequent Questions