When your loyal Xiaomi Redmi 6 Pro suddenly stops responding to the power button, it can take you by surprise: the screen stays black, the indicators don’t burn, and the phone doesn’t give any signs of life.This is a common problem that often causes panic among users, but in most cases the device is recoverable without an expensive visit to the service center.
Before you look for the nearest repair office, you need to conduct a basic diagnosis of the condition of the gadget. Often the cause of the black screen is not a fatal motherboard failure, but a software failure, a deep battery discharge or a sticking system processes. Understanding the nature of the malfunction will save you time and money.
In this article, we will discuss in detail the algorithms for various failure scenarios, learn how to perform a forced reboot, how to enter recovery modes, and when the problem lies in the hardware that requires expert intervention.
Diagnosis and primary actions in the absence of a reaction
The first step should always be to check the power supply. Even if the charging indicator does not light up, it does not mean that the battery is completely dead. Connect the original charger and cable to the network, leaving the smartphone alone for at least 30 to 40 minutes. Sometimes the power controller goes into deep sleep and takes time to accumulate the starting charge.
If the screen is still black after a while, try to perform a Hard Reset button. To do this, press both the on and down button. Hold them for 10-15 seconds. This action breaks the electrical circuit at the controller level and causes the device to restart the bootloader.
⚠️ Warning: If the phone gets hot before turning off or while charging, let it cool completely at room temperature.Attempting to turn on the overheated device can cause permanent damage to the internal components.
Check the physical integrity of the connectors. The Redmi 6 Pro uses a Micro-USB connector that eventually unravels. Try to move the cable in the socket slightly or use another wire. Sometimes oxidation of the contacts or dust interferes with the energy transfer, creating the illusion of failure.
Software failures and entry into Recovery mode
One of the common reasons for not turning on is that MIUI is getting stuck during boot or sleep. If standard button retention doesn't work, try logging into the Recovery Mode Recovery Menu.
To enter this mode, do the following: make sure the phone is turned off (or simulate turning off), then simultaneously press the power button and the volume button (+). Hold them until the Mi logo or menu with languages appears. If the menu appears, the hardware is working, and the problem lies in the software.
What to do if the Recovery menu is in Chinese?
In the Recovery menu, the navigation is done with volume buttons, and the choice is confirmed by the power button. You will need to select Wipe Data, then Wipe All Data. This action will delete all user files, but can save the phone from a “cyclic restart” (bootloop).
- 🔍 Check if the touchscreen reacts in the Recovery menu (if it's graphical).
- 🔄 Try selecting Reboot to simply restart the system without resetting.
- 💾 Use the Connect with MIAssistant option to connect to your PC if you need flashing.
After the reset, the phone should restart. The first launch after Wipe Data can last up to 5-7 minutes. Be patient and do not interrupt the process, even if it seems that the device is stuck on the logo.
Checking the Fastboot mode and diagnosis via PC
If the Recovery menu is not available, check the Fastboot mode, which is a low-level firmware mode, and is entered by pressing the power button and the volume button (-) on the phone that is turned off, and if the image of a hare repairing an android appears on the screen, or the words "FASTBOOT", then the display and the main controllers are working.
Connect the device in this mode to a computer with the Mi Flash Tool installed or simply through Windows Device Manager. The computer must make a sound of connecting new hardware. In the Device Manager (section "Ports" or "Android Devices"), a record of "Qualcomm HS-USB QDLoader 9008" or "Android Bootloader Interface" may appear.
Having a reaction to a PC connection is a good sign, which means that the motherboard is alive, and the problem is likely to be damage to the system files or firmware, in which case flashing through the computer with a complete memory cleaner (Clean All) will help.
However, if the computer does not see the phone at all, even in Fastboot mode, and the screen remains black, the probability of hardware failure increases, in which case the software methods are powerless, and it requires disassembling the device to check the power chains.
Hardware malfunctions: battery, plumes and board
When software methods are exhausted, you have to go to hardware. In the Redmi 6 Pro, you often have problems with the outgoing display plumes or the battery connector, and the battery could just fail or swell, stop supplying voltage to the board.
Diagnostics require you to gently open the back cover (it's plastic and removes with a warm-up hairdryer or neat garment). First of all, disconnect the battery connector from the motherboard, wait 10 seconds and plug it back tightly, before a click. Sometimes the contacts oxidize, and a simple cleaning with alcohol helps restore the connection.
| Symptoms. | Probable cause | Difficulty of repair |
|---|---|---|
| Phone vibrates, screen black | Display or plume malfunctioning | Medium (module replacement) |
| The indicator flashes red. | Deep discharge or BMS problem | Low (replacement of the battery) |
| Heating in the processor area | Short circuit on board | High (rebolling/sweating) |
| Total lack of response | Power supply circuit break or controller | High (diagnosis by multimeter) |
Also worth checking out is the charging connector. In the Redmi 6 Pro, it's soldered on a sub-board that connects to the main motherboard with a flexible plume, which often leaves when it falls. Check the density of its connection on both sides.
💡
The lack of response to the power button when the charger is connected most often indicates a faulty battery or charging plume, rather than the death of the processor.
Problems with the display and touch screen
Sometimes the phone actually turns on: you hear the sound of greetings, vibrations or notifications, but the screen remains black.This is a classic sign of the failure of the display matrix or plume connecting it to the board. IPS-screen that is sensitive to impact.
You can test this hypothesis by calling the phone number from another device, and if you have a horn, and then you have a reset or a response, but the screen doesn't light up, which is a 100 percent problem in the display module, and you can also point the flashlight at the screen, and if you see a dim logo or image, you have a light that burns.
- 💡 Check for cracks on the glass, even small ones, they can damage the matrix.
- 🔌 Carefully press the top and bottom of the screen (no bigotry) when turning on.
- 🎧 Connect your headphones or Bluetooth headset to check for sound.
The replacement of the display in this model is done together with the frame, which simplifies the process, but requires accuracy when transferring speakers and plumes. Self-repair is possible with the availability of skills and tools.
When professional repairs are needed
There are situations where doing it yourself can only make things worse. If you've done all of the above steps, including resetting data and checking plumes, but the phone doesn't turn on the Xiaomi Redmi 6 Pro, the problem lies with the motherboard components.
Serious malfunctions include failure of the power controller (PMIC), failure of the processor or damage to the board tracks due to moisture, in which case professional diagnostics are required using a multimeter and oscilloscope, as well as soldering equipment.
⚠️ Warning: If your phone falls into water, do not charge or turn it on. moisture causes a short circuit that instantly disables the chips.
Also, the reason for contacting the master is the bloating of the battery. Operating a device with a bloated battery is dangerous: it can burst or ignite, it is better to replace immediately using original or high-quality analogues.