Xiaomi does not include: why and how to launch a smartphone yourself

Your Xiaomi has stopped turning on and you don't know what to do? Black screen, no power button response, or endless loading — these are problems that many users face. The reasons can range from a dead battery to serious hardware failures. In this article, we will discuss all possible ways to launch a smartphone, from the simplest to complex technical solutions.

Take your phone to the service center, 80 percent of the time, you can fix it yourself, and we'll explain in detail how to diagnose a malfunction, what buttons to press, how to charge the battery without standard methods, and even how to reflash the device if it doesn't respond at all. And if you're afraid to break something, don't worry: every step is accompanied by detailed instructions and warnings.

It is important to understand that the algorithm of actions depends on the Xiaomi model (for example, the Redmi Note 10 and Mi 11 may have different combinations of buttons to reset) and on how the problem manifests itself.

1. Charging Check: Why Xiaomi Doesn't Turn on Without Power

The most common reason Xiaomi doesn't turn on is a dead battery. Even if you're sure you charged your phone the day before, the battery might have run out due to background processes or faulty cable.

First, try connecting your smartphone to another charger. Use the original cable and power supply (or a certified Quick Charge-enabled counterpart). If the phone shows no signs of charging (the indicator doesn't burn, it doesn't vibrate), try:

• 🔌 Connect to another power source (computer, power bank, other adapter).
• 🔋 Leave on charging at least 30-60 minutes - sometimes the discharged battery begins to take charge not immediately.
• 🔄 Try another connector (if charging from a PC) or clean the port of the phone from dust.
• 🔍 Light a flashlight to the port USB-C — Maybe there was a contact or dirt.

If the phone doesn't respond after this manipulation, try a forced start: press the power button for 10-15 seconds. On some models (for example, POCO F3) you need to hold the Power + Volume combination up.

⚠️ Note: If the phone was discharged to 0% and was so for a few days, the battery could go into deep discharge mode. In this case, conventional charging will not help - you need to "wake up" the battery using a special device (we will talk about it below).

2.Right reboot: how to "reanimate" the got stuck Xiaomi

If the Xiaomi smartphone is stuck on the logo, endlessly reboots or does not respond to clicks, but vibrates or illuminates the screen – the problem is more software, in this case, hard reset will help.

The methods of forced reboot depend on the model:

If after a hard reboot the phone turned on, but is unstable (brakes, spontaneously reboots), this may indicate:

• 📱 Damaged firmware (reset or flashing required).
• 🔋 Worn-out battery (check in Settings) → Battery status).
• 🛠️ Hardware problems (for example, the dump of memory chips).

Make sure your phone is at least 30 times charged%|

Backup important data (if the phone is sometimes turned on) |

Prepare the original USB| cable

Know the phone model to choose the right firmware-->

3. Launching in Safe Mode: Diagnosing Viruses and Conflicts

If Xiaomi turns on but shuts down or runs with errors, the problem may be a conflicting application or virus, in which case the safe mode, where only system programs run, will help.

To enter safe mode:

1. Press and hold the Power button until the off menu appears.
2. Press and hold the item "Switch off (or turn off power)."
3. Confirm the transition to safe mode (the Safe mode will appear at the bottom of the screen).

In safe mode:

• 🔍 Check if the phone is stable. If so, there's a problem in one of the apps installed.
• 📱 Remove recently installed programs (especially from unknown sources).
• 🛡️ Run an antivirus (e.g. Mi Security or Dr.Web).
• 🔄 If the phone is working normally, restart it as normal.

⚠️ Warning: Safe Mode disabled all third-party apps, including Google Play and Xiaomi services. Do not try to update the firmware in this mode - this may cause a crash.

If the phone in safe mode still turns off or restarts, this indicates a hardware malfunction (most often - problems with the battery or motherboard).

4.Fastboot Recovery: When the Phone Doesn't React

If Xiaomi does not turn on at all (no vibration, no screen lights), but the computer identifies it as Qualcomm HS-USB QDLoader 9008 or Android Fastboot, you can try to restore the firmware through Fastboot mode.

This will require:

• 🖥️ Computer with installed Xiaomi drivers (you can download on the official website).
• 📁 Firmware for your model (select a stable global version).
• 🛠️ The Mi Flash Tool (download here).
• 🔌 The original cable. USB-C (better-out-of-pack).

Step-by-step:

1. Turn off the phone (if it's getting stuck - hold Power + Volume down 10 seconds).
2. Press Power + Volume down and connect the cable to your PC. Hold the buttons until the Fastboot screen appears.
3. Launch the Mi Flash Tool, select the downloaded firmware (unpacked into a folder).
4. Press Refresh – the program must identify the device.
5. Select Clean All mode and press Flash.

It takes 5-10 minutes. After a successful firmware, the phone will restart. If you have an anti-rollback error, you're trying to install an older firmware version, download the current one.

5.Battery problems: how to "wake up" a deeply discharged battery

If Xiaomi is not on or charging, and when you connect to the network, you only see a red indicator that immediately goes out - most likely, the battery has gone into deep discharge mode, in which case standard charging will not help, since the battery controller blocks the current supply.

Decisions:

• 🔋 Use a frog (external battery charger). Carefully remove the battery (if the model is collapsible), connect to the frog and charge for 10-15 minutes. Then set back and try to turn on the battery.
• 🔌 Charging through USB-OTG. Connect to the phone another smartphone with the help OTG-cable – sometimes it helps to wake up the controller.
• 🔧 Connection to the power supply 5V/2A Use a laboratory power supply or charger with Trickle Charge (slow charging).

If the battery is swelling or deformed, don't try to charge it! It's dangerous.

1. Take the phone to the service to replace the battery.
2. If you change your own, use only the original battery (for example, for the Redmi Note 9 it is BN48).
3. After replacement, perform calibration: fully charge and discharge the phone 2-3 times.

⚠️ Warning: If after replacing the battery, the phone still does not turn on, check the battery plume - it could oxidize or move away from contacts.

6. Hardware malfunctions: when to carry in the service

If none of the above methods worked, the problem is likely hardware, and here are some signs to contact the service center:

• 💥 The phone fell, got wet or was subjected to mechanical stress.
• 🔥 There is a smell of burning or the phone warms up even when turned off.
• 🛠️ Artifacts (strips, flickering) appear on the screen or it does not turn on at all, but the phone vibrates.
• 🔌 When connected to charging, a crackle or sparkle is heard.

Typical hardware malfunctions Xiaomi:

If you want to repair your phone yourself:

• 🛒 Buy original parts (on AliExpress, look for sellers rated above 98%).
• 🔧 Use plastic blades for disassembly - metal can damage plumes.
• 📹 Videotape the process – it will help to properly collect the phone back.

💡

Before visiting the service, make a factory reset (if the phone even occasionally turns on), this will protect your data from outsiders.

7.Prevention: How to Avoid Xiaomi Including Issues

To ensure that your Xiaomi will not stop turning on in the future, follow these guidelines:

• 🔋 Don't discharge your phone to 0%. Optimal charge level is 20 to 80%.
• 🔌 Use only certified chargers (especially for Quick Charge 4 models)+).
• 📱 Update your firmware regularly (but not through beta versions!).
• 🛡️ Install apps only from Google Play or Mi App Store.
• 💦 Avoid moisture, even if the phone is protected. IP53 (Like the Redmi Note 10, it doesn’t guarantee 100% protection.
• 🔄 Reboot your phone once a month, which cleans up your memory.

It's also useful to know:

• 📅 Xiaomi battery is losing ~20% capacity in 2 years. If the phone starts to run out quickly, it's time to change the battery.
• 🔧 If after the update the phone began to brake, make a reset to factory settings (Settings) → The phone. → Reset).
• 🛠️ For models with AMOLED-Avoid long-term display of static images with a screen (for example, Mi 11) - this leads to a burnout of the matrix.

💡

If Xiaomi doesn’t turn on after falling or getting moisture, don’t try to charge it.

FAQ: Frequent questions about Xiaomi malfunctions