Remote from the Xiaomi Mi TV TV Not working: full recovery instructions

You picked up the remote from Xiaomi Mi TV, You clicked on the on button, and the TV didn't respond, or worse, some buttons worked and others were ignored, a situation that many Xiaomi smart TV owners are familiar with, especially after firmware updates or long downtime. In 80% of cases, the problem is solved without contacting the service center, but for this you need to accurately determine its cause.

In this article, we'll look at all the scenarios that we can think of, from the trivial discharge of batteries to hardware malfunctions in the IR board, and learn how to diagnose the remote, reset it, reprogram it for the TV, and even control the Mi. TV No remote control in emergency cases, and we'll focus on the Mi models. TV 4S/4A/4X/5X mi TV Q1/Q2, where specific bugs with Bluetooth remotes meet.

Before you run to the store for a new remote control or carry the TV for repair, go through our checklist — in 9 out of 10 cases, the problem is solved in 10-15 minutes. And if the remote does break, we will tell you how to choose a replacement and not run into a fake.

1. Checking of elementary causes: batteries, obstacles, distance

Start with the obvious, and often the problem is little things that users don't pay attention to. The first thing you need to do is to reboot the TV. Remove the plug from the socket for 30 seconds, then turn on the TV button on the case (usually on the side or bottom), which will reset the temporary disruptions in the IR receiver.

Next, check:

• 🔋 Batteries in the remote: even if the indicator does not flash, replace them with new ones (preferably alkaline, for example, Duracell or Energizer.
• 📶 Distance and angle: Hold the remote 1–2 meters to the TV and point it directly at the IR receiver (usually located at the bottom of the screen under the logo). Make sure there are no obstacles between the remote and the TV (glass, mirrors, other devices).
• ☀️ Lighting: bright sunlight or fluorescent lights can interfere with the IR signal. Try operating the TV in a darkened room.
• 🔄 Mode Switching: Some Xiaomi remotes have a switch button between IR and Bluetooth (e.g., voice-controlled models.

If you've been doing this, the remote has been running, and the problem is that it's external. If you don't, move on to the next step. Especially when you update your Mi firmware, you get bugs. TV Up to version 3.0 and higher – this may require reconnecting the device.

2.Diagnostics of the remote: how to check if it works at all

Before you blame the TV, make sure it's the TV, not the remote control, and do a simple test with your smartphone:

1. Turn on the camera on your phone and point the Xiaomi remote with the lens upwards.
2. Press any button on the remote, holding it for 2-3 seconds.
3. If the remote is serviceable, on the phone screen you will see a flicker of the IR diode (purple or white glow).

The lack of flicker means that the remote is not emitting a signal, and the reasons may be as follows:

• 🔌 Oxidation of contacts inside the battery compartment (clean them with a cotton swab soaked in alcohol).
• 🛠️ Damage to the IR diode (crack, detachment of contacts).
• 💧 The entry of liquid into the housing (even a small amount of moisture can cause corrosion of the board).

If the remote flickering, but the TV does not respond - the problem is in the signal receiver on the Mi itself. TV. If there is no flicker, the remote is defective and requires repair or replacement, in which case you can temporarily control the TV through the Mi Remote app (available for Android and iOS).

3. Resetting remote settings and reconnecting to the TV

If the remote is functional but the TV can't see it, try resetting the connection and reconnecting the device.

For IR panels (most Mi models) TV 4S, 4A, 4X):

The IR panels don't require pairing, but sometimes the signal frequency settings are confused to reset them.

1. Turn off the TV with a button on the body.
2. Press the Menu button on the remote. + OK simultaneously.
3. Turn on the TV button on the case and check the remote.

For Bluetooth remotes (Mi) TV Q1, Q2, P1 and voice-controlled models):

Bluetooth remotes require pairing, like wireless headphones.

1. Go to Settings → Devices → Bluetooth.
2. Find it on the Mi list. TV Remote and remove it.
3. Press the Pairing button (usually located under the battery compartment cover) and hold for 5 seconds until the indicator blinks.
4. On the TV, select “Add device” and wait for pairing to complete.

If the remote still doesn't work after resetting, try updating the TV firmware - new versions of the software often fix bugs with the connection of accessories. → On TV. → Updating the system.

Make sure the batteries are charged|Check the IR diode flicker through the phone camera|Reboot the TV with a button on the body|Remove the remote from the list of Bluetooth devices (if applicable)|Update the Mi firmware TV last-minute-->

4. Control of the TV without remote control: alternative methods

If the remote is finally broken and the new one hasn’t been bought yet, there are several ways to manage the Xiaomi Mi. TV without:

The most reliable temporary option is the Mi Remote app, but if the TV is not connected to Wi-Fi, use buttons on the case. TV Q1/Q2 Android TV You can connect a wireless keyboard or mouse via Bluetooth, which will give you full control over the interface.

💡

If you have a Xiaomi smartphone, use the “Fast Connection” function (in the notification curtain) – it will automatically find the TV on the local network and offer to control it without additional settings.

5. Repair the remote with your own hands: when it makes sense

If the diagnostics showed that the remote is defective, but looks whole, you can try to repair it yourself. This is true for models where the cost of a new remote is more than 1,500 rubles (for example, for Mi). TV Master Series).

Disassemble the remote by the following algorithm:

1. Carefully apply a screwdriver or mediator to the cover of the battery compartment.
2. Unscrew the screws (usually 2-4 pieces, can be under stickers).
3. Remove the upper part of the body, do not pull too much - there may be latches inside.

Check the fee for the subject:

• 🔍 Oxidized tracks (green coating) - clean them with a swallow or alcohol.
• 🔥 Bloated capacitors or burned resistors (black dots).
• 🧲 Folded contacts of the IR diode or buttons.

A common problem is the wear of conductive rubber under the buttons. If you press no click or the "fails" button, replace the rubber membrane (you can cut out of the old remote or buy a remake on AliExpress).

⚠️ Warning: Do not use acetone or solvents to clean the board - they destroy plastic and tracks.The best option isopropyl alcohol (90% and above) or a special contact fluid.

If after repair the remote does not work, and the board shows serious damage (cracks, burned elements), it is easier to buy a new one. TV — 800 to 2,500 rubles depending on the model.

Buying a new remote: how not to run into a fake

If repairs are not possible, you will have to buy a replacement. Xiaomi's original remotes are sold in branded stores (Mi Store), on AliExpress (official sellers) and in large retailers (M. Video, Svyaznoy), but there are many fakes on the market that are seemingly indistinguishable from the original, but work unstable.

Signs of the original Xiaomi Mi remote TV Remote:

• 🏷️ Packaging: a box with the Mi logo, barcode and hologram.
• 🔍 Quality of plastic: matte, no burrs, buttons are pressed with a clear click.
• 📜 Documentation: Included is instruction in Chinese/English with QR-application-code.
• 🔋 Batteries: the original are batteries Duracell or Panasonic (in fakes – no-name).

Before buying, check the compatibility of the remote with your Mi model. TV. For example:

• Mi TV Remote (Bluetooth) – for the series Q1, Q2, P1, Master.
• Mi TV Remote (IR) — for 4S, 4A, 4X, 5X.
• Mi Universal Remote is universal, but may not support voice control.

Average prices for original remotes (2026):

⚠️ Attention: AliExpress often sells "universal" remotes for 300-500 rubles, which are positioned as compatible with Xiaomi. In 90% of cases, they work incorrectly (not all buttons function, there is no feedback.

7. Hardware malfunctions of the TV: when the IR receiver is to blame

If you've tried all the ways, but the remote still doesn't work, the problem may be in the TV itself, and most often the IR receiver -- the little black module on the front that receives the signal from the remote -- fails, and you can tell if it's not working.

• 📵 The TV does not respond to any remote control (including universal control).
• 🔦 When viewed through the camera of the phone, you can see that the remote emits a signal, but the TV does not “see” it».
• 🔌 Other TV functions (sound, image) work normally.

Repair of the IR receiver in the service center will cost 1,500-3,000 rubles, if you are confident in your abilities, you can replace it yourself:

1. Buy a new IR receiver for your Mi model TV (For example, on AliExpress on request «IR receiver for Xiaomi Mi TV 4S»).
2. Remove the back cover of the TV (a cross screwdriver and a plastic mediator will be required).
3. Find the IR receiver module (usually located on the board next to the control buttons).
4. Seal off the old module and solder the new one, observing polarity.

For Mi models TV Q1/Q2 Bluetooth remotes may be a problem with the Bluetooth module, and it's more complicated to replace and requires flashing, so you'd better contact the service.

💡

If the TV is guaranteed, do not open it yourself - this will void warranty obligations. Contact the authorized service center Xiaomi with a check and a product passport.

8. Prevention: how to prolong the life of the remote from Xiaomi Mi TV

To avoid problems with the remote in the future, follow simple rules:

• 🔋 Batteries: change them every 6 months, even if the remote is working. Use alkaline batteries (not rechargeable!).
• 🧼 Cleaning: once every 3 months wipe the remote with a dry wipe, removing dust and fat from the buttons.
• 🚫 Moisture protection: Do not leave the remote in the bathroom, kitchen or near the aquarium.
• 📱 Updates: regularly update the firmware of the TV - in new versions, bugs with the connection of accessories are fixed.
• 🔄 Backup: Buy a cheap universal remote (such as Xiaomi Mi Universal Remote) and store it in case the main one breaks.

If you rarely use a remote control (for example, control a TV via a smartphone), remove the batteries from it - this will prevent the contact oxidation. TV Q1/Q2) Avoid connecting multiple devices (earphones, gamepads) at the same time – this can cause connection conflicts.

💡

Store the remote in a microfiber case, which will protect it from dust and scratches. Cases are sold on AliExpress for a price of 100 rubles.

FAQ: Frequent questions about Xiaomi Mi remotes TV