How to properly fill up the electric soapbox Xiaomi: instructions with photos and tips

Xiaomi electric soapboxes are popular hygiene gadgets that require regular refilling with a special liquid. But many users are faced with questions: which liquid to choose, how not to damage the device when refilling and how much detergent to pour? In this article, we will examine all the nuances of the process, from preparation to the final steps.

It's important to understand that improper refueling can lead to pump failure, leaks or reduced efficiency. We will describe each step in detail, specify compatible fluids and give recommendations for post-treatment care of the device. If you're refueling an electric soapbox for the first time or want to avoid typical errors, this guide is for you.

What liquid can be used for filling

Xiaomi recommends using the original soap liquid, but alternatives are also suitable in practice, the main thing is to avoid aggressive components that can damage plastic parts or pumps.

Standard requirements for liquids:

• 🧼 Neutral pH - should not exceed 7 to avoid corrode the seals.
• 🚫 No abrasive particles -- they clog the nozzle and disable the pump.
• 🌿 Hypoallergenic composition is particularly important for sensitive skin.
• 💧 Low viscosity – thick gels may not be pumped through the pump.

The original liquid Xiaomi Mi Soap Dispenser Liquid is optimized for the device, but if it is not available, suitable analogues:

• 🧴 Dove or Lux (liquid soap without fragrances).
• 🧼 Ecover (eco-hand cleanser).
• 💦 Simple (hypoallergenic variant)

⚠️ Warning: Do not use dishware (Fairy, AOS) — it is too aggressive and can spoil the O-rings.

If you're using a non-original liquid, check it for compatibility first: apply a drop on the plastic part of the soapbox and wait 10 minutes. If the material is not cloudy or deformed, the tool is suitable.

Preparation of the soapbox for refilling

Before refueling, the device must be properly prepared to avoid leaks and breakdowns. Start by disconnecting the soapbox from the network, which will prevent the pump from accidentally operating during the process.

Next, follow the steps:

1. Remove the top cover (usually it is fixed with latches or threads).
2. Remove the remnants of the old liquid with a cotton swab or napkin.
3. Wash the tank with warm water (do not use hot water – plastic can deform).
4. Dry all the details in the air for 10-15 minutes.

⚠️ Warning: Do not use alcohol or solvents for cleaning - they break down silicone seals.

If you have old liquid with sediment in the soapbox, soak the removable parts in a solution of water and vinegar (1:1) for 5 minutes, then thoroughly rinse. This will remove lime plaque and bacterial deposits.

Step-by-step instructions for refueling

Now, to the main process, follow the instructions in strict order to avoid errors:

1. Pour the liquid into the tank. Don't fill it to the edges -- leave 5 to 10 mm of free space so that when you heat it, it doesn't leak out.
2. Set the lid back. Make sure it's tightly fixed (the click should be heard).
3. Connect the soapbox to the network. Wait for the indicator to turn green (means ready to go).
4. Test the feed. Press a button or hold your hand to the sensor, and it should come out a uniform jet without bubbles.

If the jet is intermittent or the liquid is not coming in, check:

• 🔌 Correct power connection.
• 💧 Liquid level (possibly not enough to draw the pump).
• 🔍 Clean the nozzle (clean with a needle if clogged).

Critical point: if after filling the soapbox makes a buzz, but the liquid is not supplied, immediately disconnect it from the network, this is a sign of an air traffic jam or a failure of the pump.

Frequent Mistakes and How to Avoid Them

Many users make the same gas errors, which leads to breakdowns.

• 🚰 Fluid overflows, excess products leaking and ingesting moisture on electronic components, always leave 5 to 10 mm of free space.
• 🧴 Use thick gels, which clog the pump and require dilution with water (1:1).
• 🔌 Refueling when power is on, which can cause a short circuit if fluid gets into the contacts.
• 🔄 Mixing different liquids: A chemical reaction can lead to the formation of sediment.

If the soap box stopped working after refueling, reset:

1. Disconnect the device from the network.
2. Hold the feed button for 10 seconds.
3. Connect the power and check the work.

How to care for soap after filling

To make the device last longer, follow the care recommendations:

• 🧼 Weekly cleaning. Rinse the tank and nozzle with warm water.
• 🔋 Disconnect from the grid. If the soapbox has not been used for more than 3 days, it is better to remove the plug from the socket.
• 🌡️ Avoid direct sunlight. They can warp plastic and dry seals.
• 💧 Control the humidity. In a high-humidity bath, keep the soapbox dry.

Once a month, you should do a deep cleaning:

1. Disassemble the soap box (remove the lid and remove the tank).
2. Soak the removable parts in a solution of water and citric acid (1 tsp. per 200 ml) for 15 minutes.
3. Clean the nozzle with a toothpick or soft brush.
4. Dry all the details before assembly.

💡

If the soapbox began to emit an unpleasant smell, add 2-3 drops of tea tree essential oil to the liquid - it has antibacterial properties.

Comparison of original and alternative liquids

Many users are wondering if you should overpay for Xiaomi's branded liquid, so let's compare it to its peers:

The original liquid is optimized for the soap pump and does not require dilution, but the alternatives are cheaper. If you choose a similar, prefer products marked "sensitive skin" - they are less aggressive.

Xiaomi Soap Models and Their Features

Xiaomi has several models of electric soapboxes, and the filling process may be slightly different.

• 📱 Xiaomi Mi Automatic Soap Dispenser is a classic model with an infrared sensor. 300 ml tank, lid on latches.
• 💡 Xiaomi Mijia Smart Soap Dispenser — backlit and touch-controlled. 400 ml volume, supports liquid heating.
• 🔋 Xiaomi Youpin Portable Soap Dispenser is a portable battery-powered version. It's refueled from above, without a removable tank.

In heated models (Mijia Smart), it is important to use a temperature-stable liquid - some products may become delaminated or lose their properties when heated. Before filling such a soapbox, check whether the selected detergent supports heating to 40-50 ° C.

For portable versions (Youpin Portable), avoid liquids with a high alcohol content - they evaporate faster and can damage seals during long-term storage.

💡

Heated models require special liquids – ordinary soaps when heated can lose their cleaning properties or form a precipitate.

FAQ: Answers to Frequent Questions