How to get it out right SIM-Map from Xiaomi phone: instructions for all models

Extraction SIM-Xiaomi’s smartphone card seems like a simple procedure — until you encounter a jammed tray, no paper clip, or fear of damaging the microchip. In practice, even experienced users face nuances from the differences in the design of the trays of the Redmi Note 12 and the other two. POCO X5 carefully handle hybrid slots where SIM This article covers all scenarios, from standard extraction to emergency situations where the card is stuck or the tray is not pushed.

We will not only analyze the basic instructions using a paper clip, but also alternative methods (for example, using Scotch or software switch off SIM), and give recommendations for tray care to avoid breakdowns. Special attention is paid to models with non-standard slots, such as the Xiaomi 13 Ultra with a retractable mechanism or Redmi 10C, where the tray is located under the battery cover. If you have never opened your smartphone or are afraid of damaging the sealing gums (releading to waterproof models), here you will find photo and video-step measures.

Preparation: What will be needed to extract SIM-map

Before you start extracting, make sure you have everything you need, and most problems arise from using inappropriate tools, such as when users try to open the tray with a pin or toothpick, which leads to a deformation of the mechanism.

Here is the minimum set that guarantees safe extraction:

• 📎 Paperclip for SIM-card (complete with phone) or special key. If you lost it, you will fit an unbend stationery clip with a diameter of 0.7-0.9 mm.
• 🔦 Lantern (for models with a poorly visible tray hole, for example, Xiaomi) 12T).
• 🧲 Magnet (in useful if the paper clip falls inside the body).
• 📱 Spare. SIM-card or tray (to test the mechanism if the original jammed).

If you have a hybrid slot model (like the Redmi Note 11 Pro+) that has two SIMs or SIM+ microSDs installed at the same time, prepare the container for small parts – cards and sealing gums are easily lost.

Where is the slot for SIM-card in Xiaomi: location by model

Tray for SIM-cards in Xiaomi smartphones can be located in three zones of the body: on the upper end panel, on the left / right side edge or under the removable cover (in budget models such as Redmi). 9A). Below is a table with exact location for popular series:

If your model is not in the table, check the case for a small circular hole with a diameter of ~1 mm - this is the socket for extracting the tray. In models with moisture protection (for example, Xiaomi 13 Lite), the hole can be covered with a rubber plug - it must be carefully moved to avoid breaking.

💡

Before extraction SIM-Turn off the phone or put it in flight mode, which will prevent accidental calls or SMS during a procedure that may interrupt the process.

Step-by-step instructions: how to pull out SIM-map

The standard extraction procedure is the same for most models, but there are nuances depending on the type of slot.

1. Turn off the phone (required for models with a non-removable battery to avoid short circuits).
2. Find the hole for the paper clip - it is located next to the slot (see the table above).
3. Insert the paperclip at a 45° angle and press until you click. The tray should extend 2-3 mm.
4. Carefully pull the tray with your fingers - do not pull the clip, so as not to break the mechanism!
5. Delete. SIM-card, if necessary, replace it or clean the contacts of the tray with a dry napkin.
6. Insert the tray back before clicking, making sure it is up straight (skewings will lead to poor contact).

For models with a removable cover (for example, Redmi 9A):

1. Remove the lid by putting it off the camera gap (use a plastic shoulder blade or nail).
2. Remove the battery (if it is removable) - there are slots for SIM and microSD under it.
3. Press on. SIM-map on the side - it will jump out of the fixator.

Is the phone off?|Is there a key or a key at hand?|Have a hole been found to remove the tray?|Is there a place for small details?-->

In Xiaomi models with dual SIM-card tray has an asymmetrical shape - if you insert it incorrectly (turning over), the phone will not see any of the cards.

What to do if the tray is stuck or not pushed out

If you don't push the trays out after you press the paper clip, don't put too much effort into it, it can break the spring mechanism. Here are the possible causes and solutions:

• 🔧 Paperclip too thin or too stupid → Use a paper clip with a diameter of 0.8-0.9 mm or a special key. pins and toothpicks often bend and do not reach the retainer.
• 💧 Wet or dusty. → Blow the hole with compressed air (a canister for cleaning equipment) or gently clean with a toothpick soaked in alcohol.
• 🔄 The tray was skewed during the previous installation → Try to slightly press the tray with your finger from the back (where it comes out), simultaneously pressing the paper clip.
• 🧲 Magnetic field damaged the mechanism (relevant for models with metal body) → Apply a stronger magnet to the tray location to move it from a dead point.

If the tray is halfway out and stuck:

1. Don’t pull it by force – it can cut off contacts.
2. Take a thin plastic card (such as a discount card) and gently tuck the tray on both sides, rocking it.
3. If it doesn’t help, contact the service center – self-extracting can damage the motherboard.

⚠️ Warning: Do not use metal objects (knives, scissors) to remove the tray - they can close contacts on the board or scratch the case.

How to extract SIM-Map without paper clips: alternative methods

There's no paper clip on hand, and you need to get the card out of here, right?

• 📎 Scotch or tape: Cut a strip of scotch 3-4 mm wide. Fold it with the sticky side out and put it in the gap between the tray and the case. Stick it to the tray and pull it.
• 🧵 String or line: String the string into the clip hole and tie the loop. Snatch the loop onto the tray ledge and pull the string.

Software shutdown of SIM

1. Go to Settings. → SIM-maps and mobile networks.
2. Select the SIM and turn it off.

For models with removable battery (for example, Redmi 8A) you can remove the SIM without the tools:

1. Remove the lid and battery.
2. Press on. SIM-a finger card, it will jump out of the connector.

If you are using a hybrid slot (SIM + microSD, remember: when you remove the memory card SIM-The card may fall out of the tray. Hold the phone over the table or put your hand in the back.

💡

Alternative methods of extraction SIM-The regular use of unintended tools (scotch, thread) causes wear of the tray mechanism.

Frequent Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when working with the Internet. SIM-Here are the most common ones and how to prevent them:

Especially careful with models that have moisture protection (for example, Xiaomi 13 Pro with IP68 rating). If the sealing gum is damaged, the tray will lose water protection. If the gum breaks or deforms, replace it - original parts can be ordered on AliExpress or at service centers.

⚠️ Note: If after removal SIM-card phone stopped seeing the network, check: Correct installation tray (it should enter without effort). SIM-map and slot (wipe them with a slug or alcohol). Network settings in Settings → SIM-maps and mobile networks → Mobile network settings (network mode may have gone down) 4G/5G).

Care for the slot SIM-Maps: How to prolong his life

Tray for SIM-Cards are one of the most vulnerable mechanical elements of a smartphone. To avoid future retrieval problems, follow these guidelines:

• 🧼 Cleaning contacts: once every 3-6 months, wipe the contacts of the tray and SIM-It's a dry soft cloth or cotton swab dipped in isopropyl alcohol, and it'll remove the oxidation and dust that degrade the signal.
• 🚫 Avoid moisture: After hitting the phone in the rain or water, dry the tray for 12–24 hours before extraction. SIM-Moisture can cause contact corrosion.
• 🔄 Proper installation: Always insert the tray before you click. If it doesn't lock, check if dust or foreign objects interfere.
• 🛡️ Dust protection: In models without moisture protection (for example, POCO M5) You can stick a thin strip of tape on the tray slot to reduce dust intake.

If you change often SIM-Cards (e.g., on trips), consider using eSIM – many new Xiaomi models (starting with Xiaomi 12) support virtualization. SIM-This will save you the need to physically remove the tray.

To check for eSIM support in your model, go to Settings → About Phone → Full Specification and find the “eSIM” option. If you have one, you can activate virtual SIM from your carrier (supported by MTS, Beeline, Tele2 and MegaFon).

FAQ: Answers to Frequent Questions