Xiaomi Redmi Note 8 Pro is one of the most popular smartphones of the brand, but even experienced users sometimes have difficulties with extraction. SIM-Unlike the flagship models with electronic trays, this is a classic mechanical slot that requires carefulness. If you have never taken out a tray before or are afraid of breaking a paper clip, this guide will help you understand all the nuances of the matter.
In this article, we will explain in detail where the SIM slot in the Redmi Note 8 Pro is located, what tool you will need, and how to avoid typical errors - from a jammed tray to damage to contacts. And if you already have problems (for example, the slot does not retract or is stuck), you will find solutions in this case.
Where is the slot for SIM-Maps in Redmi Note 8 Pro
In Xiaomi Redmi Note 8 Pro tray for SIM-The card is located on the left side of the case - between the volume buttons and the headphone slot (if you look at the phone with the screen to yourself), this is the standard place for most Redmi models, but some users confuse it with a microphone or speaker.
To avoid making a mistake, pay attention to a small hole with a diameter. ~1 mm is the tray extractor socket, and there's usually a little pictogram next to it. SIM-I've got a map, but on some versions of the case, it can be erased or covered with a cover. If you can't see the hole, try to light it up with a flashlight or remove the protective case.
- 📍 Exact location: left face, between volume buttons and 3.5mm audio jack.
- 🔍 Signs: small round hole (not to be confused with microphone!).
- ⚠️ Careful: Don’t try to push the speaker or microphone – it can cause damage.
If you're still in doubt, look at the back of the smartphone: the tray is always on the side where the main camera is located (in the Redmi Note 8 Pro, it's the left side). On some models, the hole can be slightly recessed into the body - this is normal and does not interfere with the extraction.
What tools will be needed to extract SIM-map
To extract the tray in the Redmi Note 8 Pro, the manufacturer recommends using a special key (clip) that comes with the phone, but if you lost this tool, alternative options are suitable, the main thing is that the item is thin, durable and not bendable.
Here’s what you can use instead of a brand nameplate:
- 📎 Regular paper clip: unwind it so that you get a straight end of length ~3 cm The diameter of the wire should not be thicker than 0.5 mm.
- 🔧 Needle or pin: A sewing needle or English pin will do, but be careful – they can break when pressed hard.
- 📱 Paperclip from another smartphone: if you have a tray from Samsung, Huawei or iPhone, their paperclips will also work.
- 🔨 Thin drill or sewer: only if you are confident in your abilities - metal tray is easy to bend.
It is not recommended to use:
- 🚫 Toothpicks or matches – they are too soft and crumble.
- 🚫 Knives or scissors - you can scratch the body or damage the tray.
- 🚫 Plastic objects (pens, rulers) – they bend and do not create the necessary pressure.
If you are afraid of damaging your phone, it is better to buy a universal key for your phone. SIM-trays (worth it) ~50-100 rubles in accessories stores. It is suitable for all smartphones and reduces the risk of breakdown.
💡
Before extraction SIM-Turn off the smartphone – this will prevent accidental button pressing and save battery power.
Step-by-step instructions: how to remove SIM-Map from Redmi Note 8 Pro
Now, to the process itself, follow the instructions carefully, and if you do it right, the tray will move out effortlessly.
- Turn off your smartphone. This is not necessary, but it is recommended to avoid accidental touch of the screen. If the phone is on, put it in flight mode (Settings). → SIM-maps and mobile networks → Flight mode).
- Put the paper clip in the hole. Take the tool and gently insert it into the hole on the left side of the Redmi Note 8 Pro. Press it perpendicular to the body, without tilting. You'll feel a slight resistance -- that's okay.
- Press until you click. If you press it right, it will slip in a little bit, then it will push out 1 to 2 mm. You don't have to push it hard enough, but you have to press it with confidence. If the tray doesn't come out, don't try to pull it out with your fingers, so you can bend the mechanism.
- Take out the tray completely. When the tray is extended a few millimeters, gently pull it with your fingers over the protruding part. It should come out without resistance. If the tray is tight, don't pull it -- check if the cover or protective film is disturbing.
If the tray is not pushed out the first time, try to slightly change the angle of pressing or use another tool. Sometimes the problem lies in the accumulated dust - in this case, you can carefully blow the hole with compressed air (for example, with a can of cleaning equipment).
Is the smartphone off?|Is there a paper clip or alternative tool at hand?|Does not interfere with the cover or protective glass?|Is there any visible damage to the tray opening?-->
What to do if the tray is stuck or not pushed out
Sometimes the tray SIM-The Redmi Note 8 Pro can jam for several reasons: dust, machine deformation after a fall, or sloppy extraction last time. Don't panic, 90 percent of the time, it can be solved without repair.
Here's what we can do:
- 🔧 Try another tool. If the paperclip is too thin or bends, take a stronger object (like a needle or a stitch). Sometimes it's enough to change the angle of pressing slightly.
- 💨 Clean the dust hole. Use compressed air (a balloon) or a soft brush to remove dirt. Don't blow with your mouth, so you can introduce saliva, which then dries out and blocks the mechanism even more.
- 🔄 Try inserting the tray back and pulling it out again. If the tray is halfway out and stuck, gently press it with your finger to get it back to its original position, and then try again.
- 🛠️ Use duct tape (as a last resort). If the tray is pushed out but not pulled out with your fingers, stick a piece of tape to its end and pull. Don't use pliers or other metal tools - they will scratch the body.
⚠️ Attention: if the tray does not extend even after several attempts, do not apply excessive force. This can lead to failure of the mechanism or damage to the motherboard.
If the phone falls or is subjected to mechanical stress, the problem can be more serious, for example, bend the tray itself or damaged the connector on the board, in which case, self-extracting can aggravate the breakdown.
What to do if the tray breaks inside the phone?
How to insert it correctly SIM-map
Remove the tray is half the battle, and it's equally important to properly set it back to avoid communication problems or damage to contacts. The Redmi Note 8 Pro supports:
- Two nano-SIM cards (the tray is hybrid, the second slot can be used under microSD).
- One nano-SIM + microSD card (up to 256 GB).
Here's how to insert SIM-map:
- Place the tray on a flat surface. Make sure it's free of dust or debris. The contacts (gold stripes) should be clean -- wipe them with a soft cloth if necessary.
- Place it. SIM-Nano-SIM is mounted by a chip down, beveled angle to the corresponding corner of the tray (usually marked with an pictogram). SIM-cards, the second is installed similarly in the upper slot.
- Put the tray back in. Put the tray right into the slot. It should come in without effort -- if you feel resistance, check if the cards are set correctly. Don't push hard, you can bend the contacts.
After installation, turn on the phone and check if it is determined. SIM-If there's no communication:
- 🔄 Reboot your smartphone.
- 📶 Check if the mobile network is enabled in the settings (Settings) → SIM-maps and mobile networks).
- 🔧 Try re-installing. SIM-map - it may have been inserted crooked.
⚠️ Note: if after installation the phone does not see the tray SIM-Give your smartphone 1-2 minutes to initialize, sometimes the connection doesn't come immediately.
Frequent Mistakes and How to Avoid Them
Even experienced users sometimes make mistakes when working with the Internet. SIM-Here are the most common of these and how to prevent them:
| Mistake. | Effects of consequences | How to avoid |
|---|---|---|
| Use of inappropriate tools (knife, toothpick) | Scratching body, bent tray, jammed mechanism | Use only a metal clip or a special key |
| Pressing the tray too hard | Breakdown of the spring mechanism, damage to contacts | Press smoothly, without jerking. If it doesn't work out, check the angle of pressing. |
| Installation SIM-chip-up or not-up | The phone can't see. SIM-map, possible scratches on the chip | Check with the pictogram on the tray - the bevelled corner should coincide |
| Removing the tray when the phone is turned on (during a call or data transfer) | Mobile network failure, possible loss of unsaved data | Always turn off your smartphone or put it in flight mode before retrieving it. |
| Getting moisture or dirt into the slot | Corrosion of contacts, unstable work SIM-map | Keep your phone in a dry place, clean the slot with compressed air if necessary. |
Another common problem is that the tray doesn't lock after installation, and this happens if:
- 🔹 SIM-map is set curved and prevents the latch.
- 🔹 The spring mechanism inside the slot has weakened (often after repeated extraction).
- 🔹 The slot got garbage (dust, grains of sand).
If the tray is not fixed, try:
- Gently blow the slot with air.
- Make sure that SIM-map.
- A little press on the tray with your finger before clicking (but do not overdo it!).
💡
If the tray falls back after installation, the locking tongue inside the slot will most likely bend, in which case only replacing the tray in the service will help.
Video Instructions and Additional Advice
If you find it easier to perceive information visually, watch the official video from Xiaomi on extraction. SIM-maps (available on Mi Community YouTube channel:
- 🎥 The angle of pressing the paper clip - it should be strictly perpendicular.
- 🎥 Click sound – this is how the mechanism should sound when extracted correctly.
- 🎥 Situation SIM-maps in the tray - how exactly it is oriented.
Additional advice:
- 🔋 If you often get out SIM-card (for example, for trips abroad), buy a spare tray - this will prolong the life of the mechanism.
- 📱 If the phone is in the case, remove it before removing the tray - so you avoid accidental pressure on the case.
- 🔄 If SIM-The card stopped being determined after extraction, try resetting the network settings (Settings) → SIM-maps and mobile networks → Resetting network settings).
In Redmi Note 8 Pro tray for the SIM-The card has no electronic lock, so it can be removed even with a discharged battery - it is safe for the phone. However, if the battery is completely dead, it is better to first charge the smartphone a little (at least to 5-10%) to avoid problems with initializing the card after installing the card.