How to straighten the case of Xiaomi smartphone: safe ways and mistakes that should be avoided

The deformed body of Xiaomi’s smartphone is a problem that many users face after falls, pocket pressure or careless handling. Even a slight bending can lead to screen cracks, battery detachment or button disruption. In this article, we will discuss all possible methods of straightening the case, from simple home methods to professional techniques, and explain when to contact the service center.

It is important to understand that not every bend can be repaired independently. For example, if the body is bent near the charging connector or speaker, the risk of damage to internal components increases significantly. X3, Mi 11 Lite, and we will give you recommendations for each case, you will also learn what tools you will need and how to avoid typical repair errors.

The reasons for the deformation of the Xiaomi body: why it happens

The case of the Xiaomi smartphone can bend even from a slight mechanical impact.

• 📱 Falling to a hard surface is the most common cause: impact on asphalt or tiles deforms the aluminum frame, especially in models with a thin body (Mi 11 Ultra, Redmi). K40).
• 👖 Pocket pressure: Sitting on your phone or wearing tight jeans causes a gradual bending, and plastic-body models are more likely to suffer. 9A, Poco M3).
• 🔥 If the smartphone is frequently heated (e.g. during games), metallic elements can lead over time.
• 🛠️ Poor repairs. Once the screen or battery is replaced, the body may not be properly assembled, causing deformation.

Especially vulnerable models with aluminum frame and glass back panel – for example, Xiaomi 12T Or the Redmi Note 12 Pro.+. Plastic enclosures (Redmi) A1, Poco C40) They are less likely to bend, but they can burst under strong pressure.

⚠️ Attention: If the body is bent near the antenna lines (upper or lower), this can degrade the signal of the network.

Diagnosis: how to determine the degree of deformation

Before you start straightening, you need to assess the extent of the damage.

1. Visual inspection: Put your phone on a flat surface (like a table) and see if there are gaps between the body and the surface, and if the smartphone is swinging, it's severe.
2. Check the buttons. Press the volume and power buttons: if they go down or wedge, the body could bend in their area.
3. Screen test. Swipe your finger around the edge of the display, and if you feel a wave or a gap between the glass and the frame, it's a sign of a bend.
4. Check connectors. Insert the charging cable, if it hangs or doesn't fit in until the end, it might be bent. USB-port.

For accurate diagnosis, you can use a laser layer or an equalizer application (for example, Bubble Level). 1-2 Self-exercising can be dangerous.

💡

If the body is bent near the camera, check the focus: even a small bend can knock down the autofocus setting.

Preparing for straightening: tools and safety measures

To self-righten the case Xiaomi you will need:

• 🔧 Plastic blades (for careful smearing of the body).
• 🛠️ Thin screwdriver (cross or flat, depending on the model).
• 🧲 Magnetic substrate (so as not to lose the screws).
• 🔥 Hair dryer or thermo-air station (for softening glue).
• 📏 Line or rod (for measuring bending).
• 🧴 Isopropyl alcohol (for cleaning contacts after disassembly).

Also prepare the workplace:

• Cover the table with a soft cloth so as not to scratch the phone.
• Use an antistatic bracelet if you are disassembling the phone completely.
• Take a picture of each stage of the showdown, it will help to collect everything back.

⚠️ Warning: Do not use metal tools to straighten – they may leave scratches on antenna lines, which will worsen the signal 4G/5G and Wi-Fi.

Turn off the phone and remove it SIM-map|Remove the cover and protective film|Prepare tools and workplace|Check the degree of deformation of the ruler|Take a picture of the original state of the phone-->

Method 1: Undisassembled straightening (for mild deformations)

If the bending is slight (up to 0.5 mm), you can try to straighten the body without completely disassembling. This method is suitable for models with a plastic or aluminum body (Redmi 9, Poco). M4 Pro).

Step-by-step:

1. Place the phone on a soft surface (such as a towel).
2. Carefully press the convex part of the body evenly, without jerking. Use a plastic card or a shoulder blade as a lever.
3. If the body does not lend itself, slightly heat the bending site with a hairdryer (temperature not higher than 60).°C).
4. Repeat the pressure, gradually increasing the force.

For models with glass back panels (Xiaomi 12, Redmi Note 11 Pro), this method is not recommended - the glass may crack. Also avoid heating near the battery!

Method 2: Partially disassembled straightening (medium deformation)

If the body is bent strongly (up to 1.5 mm), but without cracks, partial disassembly is required, a method suitable for most Xiaomi models, except for the flagships with complex design (Mi Mix, Black Shark).

Algorithm of action:

1. Turn off your phone and remove the back cover (if it's removable). For models with a glued panel (Redmi Note 10), use a dryer to soften the glue.
2. Disconnect the battery plume (required!) to avoid short circuit.
3. Look at the inner frame. It's usually bent near the frame: 🔋 Charging connector; 🔊 Dynamics; 📷 Camera module.

linden

Collect the phone in reverse order, checking the operation of all buttons and connectors.

For models with metal frame (Poco) F3, Xiaomi 11T) You may need a press or a soft-laden press, and without experience, you'd better not take risks, because the wrong pressure can damage the motherboard.

⚠️ Warning: If the phone doesn't turn on after straightening, check the plumes for breaks. Most often the plume of the display or battery suffers.

💡

Partial disassembly allows you to control the straightening process more accurately, but it requires care. If you're not sure about yourself, contact the service.

Method 3: Professional tools and when to use them

For severe deformations (more than 1.5 mm) or if the body is bent in several places, you will need professional tools:

• 🔧 Hydraulic press – used for uniform pressure distribution, suitable for Xiaomi with metal body (Mi 9, Mi 10).
• 🔥 Thermoplastic form - heats the body up to 80-100°C, after which it can be straightened without the risk of cracks.
• 🛠️ Ultrasonic cleaner – helps remove glue residues after disassembly, making it easier to access the frame.

These tools are usually only available in service centers, and the cost of professional straightening in Russia (2026) ranges from 1,500 to 4,000 rubles, depending on the model and the degree of damage.

When you should contact professionals:

• The body is bent near the antenna lines (upper / lower part).
• There are cracks on the screen or back panel.
• After the phone was straightened, it stopped turning on.
• The strain affects the camera or Type-C connector.

What not to do when straightening the case Xiaomi

Some folk methods can make the problem worse or completely disable the phone, and this is strictly forbidden.

• 🔨 Use a hammer, even through the fabric, and it will cause cracks in the body or damage to the internal components.
• 🔥 Heat the body with open fire (lighter, gas stove) Temperature above 100°C will melt plastic and damage battery.
• 🧲 Use strong magnets to pull the body, which can disrupt the compass and the Hall sensor.
• 💧 Water the body with boiling water (yes, this is the advice!) Moisture will fall under the screen and disable the sensor.
• 🔧 Use pliers or visceralties without protection. Metal sponges will leave scratches and dents.

You should also not try to straighten the body if:

• The phone was in water - corrosion weakens the metal and it can burst.
• There are already cracks on the screen – the pressure will lead to their spread.
• The battery is swelling - the risk of fire!

💡

If after an unsuccessful attempt to straighten the phone began to warm or quickly discharge, immediately take it to the service - this is a sign of damage to the battery or motherboard.

FAQ: Frequent questions about the straightening of the Xiaomi body