How to get out SIM-Xiaomi Redmi 6: safe ways and expert advice

Xiaomi Redmi 6 is a popular budget smartphone that is still widely used due to its reliability. SIM-The wrong manipulation can lead to jamming of the tray, damage to contacts or even break the body. In this article, we will discuss all the official and alternative ways to remove the SIM from Redmi 6, and also explain how to avoid typical errors.

The Redmi 6 features a hybrid slot for two nano-SIMs or one SIM + microSD. This means that the tray here is more fragile than in the flagship models. If you have never removed a SIM from this smartphone or encountered the fact that the tray is not retractable, our instructions will help solve the problem without going to the service center.

Before you start, make sure you have a key to remove the tray (company with your phone) or its analogue on hand. If you don't have the key, don't panic: we'll tell you how to replace it without risking the device.

Preparation: What will be needed to extract SIM-map

Before removing the Sim from the Xiaomi Redmi 6, prepare the necessary tools and workplace, which minimizes the risk of losing parts or damage to the phone.

Here is a complete list of what might be useful:

• 🔑 Key to extract the tray (original from the kit or metal clip)
• 📱 A flat surface (table, tray) for placing the phone and small details
• 🔦 Lantern (to better see the hole for the key)
• 🧲 Magnet (in case the tray falls out and rolls under the furniture)
• 🧴 Alcohol wipes (to clean the contacts of the simk if necessary)

If you don’t have a brand key, you can replace it with an unbended stationery clip or even a thin needle (but with caution!). The main thing is that the tool is strong enough and does not bend when pressed. The diameter of the hole for extracting the tray in Redmi 6 is approximately 0.8-1 mm, so any object with a similar cross section will suit.

⚠️ Warning: Never use toothpicks, plastic sticks or other soft materials to retrieve a tray, and they can break inside the hole and it will be extremely difficult to get the debris out.

Also make sure that the phone is turned off before you pull the SIM. This is not a requirement, but this will eliminate the risk of accidental button pressing or device failure. If the SIM is stuck and not retrieved in the standard way, do not make excessive efforts. In the next section, we will tell you how to deal with this situation.

Official method: extracting the tray with a key

The safest and most recommended method by the manufacturer is to use the original key.

1. Put the Xiaomi Redmi 6 on a flat surface with the screen up. SIM-The card is located on the left end of the device (if you look at the screen).
2. Put the key in a little hole next to the tray. Push it all the way until you feel a little click. The tray should move out a little bit.
3. Carefully pull the tray over you, holding it by the edge. Don't make any effort - it should come out smoothly.
4. Get it. SIM-Notice the notch in the corner, which should match the shape of the nest.

If the tray doesn't retract the first time, try to sway the key slightly in the hole or press from different angles, sometimes dust or small debris prevents the mechanism from working, and in extreme cases, you can blow into the hole to remove the contamination.

Important: Redmi 6 has a two-sided design, which means that SIMs can be installed on either side (for example, to use two operators or a SIM + memory card). However, if you use a microSD, the second SIM will not fit - this is a restriction of the hybrid slot.

⚠️ Note: When installing the tray back, make sure that SIM-If the SIM card is wobbly or crooked, the phone may not recognize it or show an error".

Alternatives: What to do if there is no key

The situation where the original key is not at hand is familiar to many, and fortunately there are several proven ways to remove the tray without it, the main thing is to act carefully so as not to damage the mechanism.

Here are 3 reliable alternatives:

• 📎 A paper clip or a stationery pin. Spread the paper clip so that you have a straight metal bar. Put it in the hole and press it. The effort should be moderate -- light enough pressing.
• 🧷 Sewing needle (thick) is suitable if there is nothing else at hand, the main thing is not to pierce the sealing ring inside the hole.
• 🔧 Thin screwdriver (flat) Use only as a last resort. Screwdriver must be very small so as not to damage the body.

If none of the items work, you can try heating, put the phone in a warm place (for example, under a lamp) for 5-10 minutes, heat expands the plastic, and the tray can move out more easily, but do not overheat the device - enough temperature to 40-45 ° C.

Another life hack is to use a sticky tape (scotch) glue a piece of tape to the edge of the tray (if it protrudes a little) and pull it, which works if the tray is pushed 1-2 mm, but not further.

If all attempts failed, the problem may be that the tray mechanism broke down, in which case it is better to contact the service center so as not to aggravate the situation, and self-repair can damage the motherboard.

Frequent Mistakes and How to Avoid Them

Even something as simple as extraction. SIM-And if you make mistakes, you can make problems with these cards, and you can look at the most common ones and how to prevent them.

One of the most dangerous mistakes is to use excessive force on a jammed tray, and many users try to pull it out with pliers or other tools, often resulting in the breakdown of the plastic rails or even the tray being removed from the mechanism, and if the tray does not respond, it is better to use alternative methods (such as heating) or consult a specialist.

Another problem is getting moisture or dust into the slot for SIM-This can lead to corrosion of contacts or a bad signal.To avoid this, periodically blow the tray hole with compressed air (for example, a spray to clean equipment) and avoid using the phone in high humidity conditions.

💡

If you often get out SIM-card (for example, when traveling abroad), lubricate the guide tray with a small amount of silicone lubricant. This will facilitate its movement and protect against wear and tear.

How to extract SIM-card if the tray is broken

If the tray mechanism fails (for example, the spring broke or the plastic latches cracked), you can remove the SIM without it, but this process requires caution so as not to damage the contacts inside the phone.

Here is a step-by-step instruction for emergency extraction:

1. Turn off your phone and remove the back cover. In Redmi 6, it's mounted on the latches, so put a plastic spatula (or mediator) on the bottom edge.
2. Carefully disconnect the battery plume to avoid short circuits, so put the connector in a thin screwdriver.
3. Find a slot for SIM-It's located next to the camera plume connector.
4. Use tweezers to extract SIM-Hold it by the edges without touching the contacts.

If you're not sure about your skills, you should have a professional to do this, and if you're unskilled, you can damage the plumes or other components, and if you're not sure if you're going to take them out, you're going to have to replace the trays, and you can't use the phone without it.

⚠️ Warning: When disassembling the Redmi 6, be careful about the flexible plumes, which are very fragile and can break even with a little effort. If the battery plume breaks off, the phone won't turn on without repair.

The cost of replacing the tray in the service center usually does not exceed 500-800 rubles, while self-repair can cost more if something goes wrong.

Cleaning contacts SIM-maps: when and how to do

If the phone stopped seeing SIM-If you look at the map, the problem might not be in the tray, but in the contaminated contacts, and the dust, the oxidation, the random fluids, can disrupt the connection, and let's look at how to clean the contacts properly without risking damage.

You'll need:

• 🧴 Alcohol (isopropyl or medical 90)+%)
• 🧻 Cotton swabs or a walnut-free wipe
• 🔍 Lupa (optional for a better view)

Cleaning process:

1. Extract. SIM-tray-card.
2. Soak the cotton swab in alcohol and gently wipe the gold contacts on the map. Don't press hard!
3. Let the map dry in the air for 2-3 minutes.
4. In the same way, clean the contacts inside the tray.
5. Install. SIM-card back and check the work.

If the problem persists after cleaning, try inserting the SIM into another phone. If it doesn't work there, it means the card is damaged and needs to be replaced by the operator. If the SIM works on another device but not in Redmi 6, the problem may be in the phone slot (for example, bent contacts).

💡

Never use abrasive materials (sandpaper, eraser) or aggressive liquids (acetone, gasoline) to clean contacts, which will damage the protective coating of the contacts and accelerate their corrosion.

Video instruction and additional resources

If you find it easier to perceive information visually, we recommend watching a video with step-by-step extraction. SIM-There are no official videos from Xiaomi on this topic, but there are many quality reviews from users and service centers.

When choosing a video, pay attention to the following points:

• 🎥 Date of publication: Make sure the video is up to date (no older than 2-3 years old).
• 👍 Rating and comments. See if there are any complaints of inaccuracies in the instructions.
• 🔍 Details. A good video shows the process from different angles and close range.

Here are a couple of verified YouTube channels where you can find helpful instructions:

• Xiaomi Today is a channel with reviews and instructions on Xiaomi devices.
• GSMArena is an international resource with detailed analysis of smartphones.

If you prefer text guides, the 4PDA and Mi Community forums have detailed topics with photos and tips from power users, such as “Redmi 6 SIM tray stuck” or “how to open Redmi 6 without key”.

FAQ: Answers to Frequent Questions