When a Xiaomi smartphone suddenly stops responding to clicks and the power button doesn't work, it causes panic in any owner.The gadget can be completely discharged, hang in a reboot cycle or have a hardware key failure. Depending on the model, whether it's a budget Redmi or flagship Xiaomi, the methods of resuscitation may differ, but the basic principles remain similar.
Before you bring a device to a service center, you should try software and alternative physical ways to activate the system. Often the problem is not a failure, but a deep discharge or software failure that can be fixed without replacing components.
In this article, we’ll look at all the known ways to turn on a Xiaomi phone without the power button if it’s turned off.We’ll take a look at methods from simple charging to complex manipulations with engineering menus and computer usage.
Diagnosis and primary actions in the discharge
The most common, but common, reason for the lack of response is the deep discharge of the battery. When the voltage drops below critical levels, the smartphone can not start even the charging screen. In MIUI devices, the indicator may not light up the first few minutes of connection to the network.
Keep the device on charge for at least 30-40 minutes, even if the screen is black. Use the original power supply and cable, as third-party accessories may not give enough current to "push" the battery. If the phone is heated but the screen is not lighting up, this may be a sign of a problem with the power controller.
Sometimes it helps to pump the battery, so you have to plug the charger in, wait. 10-15 Set it off, wait for it. 10 - I'll be back on the phone. 3-5 This can activate the chemical processes in the lithium-ion cell and raise the voltage to the level necessary to start the loader.
⚠️ Warning: If the case of the smartphone is very swollen or the smell of burning is heard, immediately stop any attempts to charge.
☑️ Primary diagnosis
Use key combinations to log into Recovery
If the power button is physically broken, but other buttons (volume) are working, you can try to enter the recovery mode.This menu allows you not only to reset the settings, but in some cases, to initiate a restart of the system that will start the phone.
Most Xiaomi and Redmi models use a button combination to log in to Recovery Mode. Press the Volume Up button and plug a USB cable that goes to your computer or charger. Hold the button until the Mi logo or Recovery menu appears.
In the Recovery menu, you can navigate with volume buttons and select with the power button. If the power button doesn't work, this may not be a useful method for selecting an item, but the fact that you log in to the menu confirms that the hardware is alive, and sometimes just being on the menu for a few minutes and then turning off the cable triggers an automatic start.
What if Recovery doesn’t let you go?
Connection method to computer and Fastboot
Fastboot mode is a low-level interface for firmware and diagnostics that is available even when the phone is off, and logging into this mode often helps wake up the device by making it respond to external signals.
To get into Fastboot, press the Volume Down button and connect it. USB-You're going to see a bunny fixing an android or something that says, FASTBOOT. If the screen is black, but the computer has made a sound of the connection of the new device, then the phone is turned on, but does not provide the image.
While in Fastboot mode, you can try to exit it by (holding) the volume button for 10-15 seconds. On some models, this action forcibly reboots the device to normal mode. You can also use commands via PC if you have installed Xiaomi USB Driver drivers.
💡
Use the original. USB-Cheap cables often only transmit charge, but not data, which blocks the entrance to the Fastboot.
Application ADB-remotely-include commands
For advanced users who previously had USB debugging enabled, there is a way to turn the phone on software, which works if the phone is not completely off, but is in a state of deep sleep or freeze, and the battery has a charge.
You need to install the ADB Tools and drivers on your computer. Connect your phone to your PC. Open the command line and type in a command to check the connection:
adb devicesIf the device appears in the list, you can send a command to restart, which is equivalent to turning on:
adb rebootIn some cases, the adb reboot bootloader command helps, which will force the boot process to start. However, if the phone is completely off (Hard Off), the software methods through the ADB will not work, since the processor does not receive power.
Hardware methods and contact closure
If the software is powerless, you have to physically push the board, and it's a very careful method that's suitable for people who aren't afraid to open the back cover, and the idea is to simulate pushing the power button directly on the board.
To do this, remove the back cover (or screen if the cover is not removable) and find the power button plume. Carefully unplug the plume. Then take a tweezer or a thin screwdriver and lock the two contacts on the board that the button plume was connecting to.
Closing contacts simulates pressing, at which point the screen should light up or vibration will appear. Once successfully enabled, it is recommended to configure the function "Dual tapping" or install an emulator application if root rights allow you to control power.
| Method | Difficulty | Risk of damage | Efficiency |
|---|---|---|---|
| Charging (30+ min) | Low. | No. | Medium |
| Recovery (Vol +) | Medium | No. | Tall. |
| ADB Teams | Tall. | No. | Low (no root) |
| Close of contacts | Very high. | High-pitched | Tall. |
Software solutions for automatic inclusion
If you managed to turn your phone on temporarily (for example, through Recovery or a circuit), but the button still does not work, you need to urgently protect yourself from turning off again. MIUI Android has features that automate this process.
Find the Battery and Performance (or Advanced Settings) section on the menu, and often the "On/Off Planner" option is hidden there. Set a daily turn-on time, for example, at 08:00 a.m. Now, if the phone turns off at night or runs out, it will try to turn on itself at a predetermined time.
Also worth considering is installing apps from Google Play that change the behavior of volume buttons, such as Button Mapper, which allows you to assign a "Screen Turn on" or "Reset" action to a long press of volume, which will be a temporary solution before repair.
⚠️ Warning: Once successfully enabled, immediately back up the data. The broken power button is a signal that the device can shut down at any time and no longer turn on without intervention.
💡
The most reliable way to bring your phone back to life without a button is to combine Recovery and then set up auto-on on schedule.