How to turn off Xiaomi phone without a power button: all ways of 2026

A broken power button on Xiaomi is one of the most frustrating breakdowns, because a phone can turn into a brick even with a desktop screen and a charged battery. The situation is aggravated if the smartphone is completely turned off: without physical access to the Power button, it seems impossible to bring it back to life.

In this article, we’ll break down all the current ways to include Xiaomi (including Redmi models, POCO, Mi and Black Shark) without the power button, and the methods are suitable for phones with a dead battery, and for devices that "hang" on the logo. MIUI and smartphone models.

If your Xiaomi doesn’t respond to charging, doesn’t vibrate when you connect the cable, and doesn’t show signs of life, check the cable, power supply, and USB port first. In 30% of cases, the problem lies in damaged wire or oxidized contacts. If the phone is accurately receiving power (hot case, charging indicator), but does not turn on, go to the instructions below.

Broken power button |Discharged battery |Damping |Program failure |Other reasons-->

1. Energizing through the charger (the “hot reset” method)

The easiest way that works for 70% Xiaomi models including Redmi Note 10/11/12, POCO X3/X4, Mi 11/12). The idea is to simulate the power button pressing through the power connection/disconnect cycle. 10-15% (Otherwise, the phone won't react).

Connect your smartphone to the original charger (or the powerful 18W+ power supply) and follow the following steps:

• 🔌 Connect the cable to the phone and the socket. 1-2 minutes (the charge indicator should be lit).
• ⏱️ Turn off the cable from your phone for 10 seconds.
• 🔄 Reconnect. If the phone starts to boot, hold the Volume Up button for 5 seconds (this can help you get out of the getting stuck state).
• 🔋 If the screen is black, repeat the cycle. 3-5 intermittently 15 seconds.

On some models (e.g. Redmi) 9A or POCO M3) This method only works when using a fast charging cable (Quick Charge 3.0)+). If you have a universal USB-Cable, try replacing it with a branded one from Xiaomi.

💡

If the phone vibrates when you charge it, but it doesn't turn on, try holding it for 10-15 minutes and then repeat the off/on cycle. Sometimes the battery is so low that the system can't initialize the start.

2. Use of button combinations (emergency start)

Even if the Power button doesn’t work, most Xiaomis can turn on the phone through hardware combinations with volume buttons, a technique that is suitable for devices that aren’t fully discharged and that respond to a PC connection.

Try the following combinations (hold the buttons for 10-15 seconds):

• 🔊 The Volume Up button (Volume Up) + Connecting to charge – works on the Redmi Note 8/9/10 and POCO F1/F2.
• 🔈 The Volume Down button (Volume Down) + PC connection - can start Fastboot mode on Mi 10/11.
• 🔊🔈 Both Volume Up buttons (Volume Up) + Volume Down) + Charging – runs on Black Shark and some Redmi K models.

If the phone vibrates or lights up after holding the buttons, but does not load beyond the MIUI logo, there may have been a software failure, in which case a reset via Recovery will help (see section 4).

⚠️ Warning: Do not hold the volume buttons for longer than 20 seconds - this can lead to a forced reboot in the EDL-mode (emergency firmware), which will require special equipment for recovery.

Make sure the battery is at least 5 times charged%|Use the original Xiaomi cable|Try to connect to the PC and charging alternately|Hold the buttons for at least 10 seconds-->

3. Launch via ADB (if USB debugging is enabled)

If your Xiaomi has previously been activated by USB debugging (Settings → About Phone → MIUI → 7 times tap → Developer Settings → USB debugging), you can enable it through your computer using the ADB (Android Debug Bridge) tool.

This will require:

• 💻 A computer with installed Xiaomi drivers and ADB.
• 🔌 Original. USB-cable (preferably from the set).
• 📥 Google's Platform Tools (you can download it here).

Step-by-step:

1. Connect the phone to the PC.
2. Open the command prompt (Win + R → enter cmd) and go to the folder with ADB:
3. Enter a command to check the connection:
4. If the device is determined (the serial number will appear), execute the switching command:
5. If the phone is not responding, try an alternative command:

If ADB The device cannot be seen, but the phone is identified in Device Manager as Qualcomm. HS-USB QDLoader 9008 – this means that the smartphone has moved to the Internet EDL-In this case, the firmware will be required to restore via the Mi Flash Tool (see section 5).

⚠️ Attention: Teams ADB It won't work if the debugging is USB It's been disabled. In this case, move on to other methods.

4. Log in Recovery Mode and reset settings

If the phone is responding to charging (vibrates, lights up), but does not turn on in the usual way, you can try to start it through the recovery mode (Recovery), this method is suitable for devices with an unlocked bootloader or standard MIUI Recovery.

Instructions:

1. Turn off the cable and immediately press the combination: 🔊 Volume Up + Power (hold on) 10-15 If it doesn't work, try Volume Up. + Volume Down + Power (for) POCO F3, Redmi K40).

Mi Bunny

No command

Power

Volume Up

Recovery

Reboot system now

Wipe data

Some models (Mi 11 Ultra, Redmi Note 10 Pro) require a PC connection to log in to Recovery instead of the Power button.

1. Connect the phone to the computer.
2. Press Volume Up and, without letting go, insert the cable into the USB port (the recovery screen should appear).

💡

If the phone loads into Recovery but doesn't turn on normally, it could be a damaged firmware problem, and that's where flashing through Fastboot or EDL can help.

5. Firmware via Fastboot or EDL (for advanced)

If all previous methods have failed and the phone is determined by the computer (e.g. Qualcomm HS-USB or Android Bootloader Interface), the last option is the firmware via Fastboot or EDL. This method requires an unlocked bootloader (for Fastboot) or an authorized Xiaomi account (for EDL).

Step-by-step instructions for Fastboot:

1. Download Fastboot firmware for your model from Xiaomi website.

For firmware via EDL (if the phone is defined as QDLoader 9008):

• 🔧 You will need to log in to Mi Account (linked to your phone).
• 📥 Download the firmware. EDL and the Mi Flash Pro utility.

⚠️ Attention: Firmware through EDL without authorization can permanently lock the phone (requires an official unlocker from Xiaomi!

6. Alternative methods: disassembly and “closing” of contacts

If the software methods didn't help, and the Power button doesn't physically press (for example, after a fall or moisture), the mechanical way is to close the contacts of the power button on the board, which requires disassembling the phone and is only suitable for users with experience in electronics repair.

What you need:

• ⚒️ Set of screwdrivers (star, flat).
• 🔍 Loupe or magnifying glass.
• 🧲 Thin-ended tweezers.
• 🔌 Multimeter (to check contacts).

Instructions:

1. Turn off the phone and remove the back cover (heating with a hair dryer or using a suction cup).
2. Disconnect the battery plume to avoid short circuit.
3. Find the contacts of the power button on the motherboard (usually signed as PWR_KEY or KPP).
4. Close the contacts carefully with tweezers for 1-2 seconds (this simulates the press of a button).
5. Connect the battery and check if the phone is switching on.

On some models (Redmi 9C, POCO M2), the power button contacts are located under a metal screen, which requires a complete disassembly to access.

💡

Before disassembling, take a picture of the location of all the plumes and screws - this will help to properly assemble the phone back. Use plastic blades to avoid damaging the battery and screen plumes.

7. Prevention: How to avoid breaking the power button

The power button on Xiaomi breaks more often than others due to mechanical wear or dust/moisture intrusion.

• 🛡️ Use a case with button protection (for example, silicone or with reinforced sidebars).
• 🚿 Avoid getting liquid on the top of the phone (where the button is located).
• 🔄 Don’t press Power too sharply – it’s best to use the software shutdown via the menu.
• 🔋 Regularly clean the charging port and buttons with compressed air (without alcohol!).

If the button has already started to stick or requires a strong press, try preventive cleaning:

1. Turn off the phone and remove it. SIM-memory-card.
2. Apply 1-2 drops of isopropyl alcohol (90%+) to a cotton swab.
3. Gently wipe the area around the button (do not pour alcohol inside!).
4. Press the button 10-15 times to dissolve the dirt.
5. Let the phone dry for 2-3 hours before turning on.

FAQ: Frequent questions about Xiaomi powering up without power button