How to turn on Xiaomi soap: 5 working ways (including emergency)

Xiaomi Soaps are compact and functional IP-The cameras that are often used for surveillance at home, in the office or even in the country, but what if the device suddenly stopped turning on? The reasons can be different, from the banal discharge of the battery to software failure after the upgrade. In this article, we will discuss all possible ways to turn on soapboxes, including emergency methods for “brick” devices.

It is important to understand that the term "soap" users often mean two lines of devices from Xiaomi: classic Xiaomi Mi Home Security Camera (for example, models 360° 1080p or 2K Pro) and more budget Xiaomi MiJia. Despite the external differences, the principles of their inclusion and diagnosis are largely the same. If your camera does not respond to the power button - do not rush to carry it into service: in 80% of cases, the problem can be solved independently.

1. Standard inclusion of Xiaomi soapbox

If your Xiaomi camera is new or just turned off, try the following algorithm:

1. Connect the camera to the power source using the original cable and power supply (voltage should be 5V/1A or 5V/2A – check the sticker on the adapter).
2. Press and hold the power button (usually located on the bottom panel) for 3-5 seconds until the indicator lights up.
3. Wait for the beep (squeak) and the blue flashing LED – this means that the camera is ready to adjust.

If the indicator lights up red and immediately goes out, this is a sign of a dead battery (relevant for models with a battery, for example, Xiaomi Mi Home Camera Battery).

💡

If the camera doesn’t respond to the button, try using another cable or power supply – unoriginal accessories often cause problems with turning on.

For battery-free models (e.g. Xiaomi Mi Home Security Camera 360°) check:

• 🔌 Reliability of cable connection to the socket and camera connector.
• 💡 The power of the socket (connect to it another device).
• 🔋 No physical damage to the cable (excesses, melting).

2. Incorporation after firmware failure

If the camera stopped turning on after a software update or failed reset, there was likely a software failure, in which case a forced reboot or recovery via Mi Home will help.

Method 1: Hard Reset (Hard Reset)

1. Turn the camera off the power.
2. Press the power button and, without letting it go, connect the cable to the outlet.
3. Hold the button for another 10-15 seconds until you hear a double beep.
4. Release the button – the camera should start the recovery process (the indicator will flash yellow).

Method 2: Recovery through Mi Home

• 📱 Install the Mi Home app (version no lower than 6.5.4).
• 🔄 Go to the Devices section → Add the device → Cameras.
• 🔍 Select your soapbox model and follow the instructions on the screen.
• ⚙️ When the error "Can not connect" click "Repeat attempt" 3-4 Sometimes the system restores the connection itself.

3. Diagnosis by indicators: what do colors mean

The color and behavior of the LED on Xiaomi’s soapbox is the key to understanding the problem.

If the indicator does not light up at all, the problem may be:

• 🔋 Fully discharged battery (for models with battery).
• 🔌 Faulty power supply or cable.
• 🛠️ Damaged motherboard (diagnosis required).

4. Turn on the soapbox without the power button

What if the power button is broken or doesn't respond to the press? There are a few workarounds:

Method 1: Connect via USB to a PC

1. Connect the camera to the computer through USB-cable (use the port) USB 3.0 for stability).
2. Open Device Manager in Windows and check if a new device has appeared (e.g., "Unknown Device").
3. If the device is determined, try to update the driver manually through the Mi PC Suite (download from the official Xiaomi website).

Method 2: Hardware reset via contacts

For models with a collapsible body (for example, Xiaomi Mi Home Camera 1080p):

1. Carefully remove the back cover (use a plastic shoulder blade to avoid damaging the latches).
2. Find contacts with the RST or RESET label on the board (usually located next to the battery).
3. Close the contacts with a metal object (for example, a paper clip) for 5-7 seconds.
4. Connect the power - the camera should turn on in recovery mode.

⚠️ Warranty: If the device is warranty-free, contact the Xiaomi service center - in Russia, repair warranty takes up to 14 days.

5. Problems with battery models

Battery models (such as Xiaomi Mi Home Camera Battery) have additional nuances. If the camera doesn't turn on, check:

• 🔋 Charge level: Connect the camera to charge at 4+ Even if the indicator does not burn, the battery could run out to zero.
• 🔌 Battery Contacts: Remove the Battery, Wipe the Contacts with Alcohol and Set Back.
• 🔄 Charging cycles: Lithium-ion batteries lose capacity after 300-500 If the camera is older than the cycles 2 In the years to come, battery replacement may be required.

To check the status of the battery:

1. Connect the camera to the Mi Home.
2. Go to the device settings → Battery status.
3. If the capacity is below 20%, charge fully before use.

Important: The batteries in Xiaomi soaps are not meant to be replaced by a user!When you try to replace the battery yourself, the risk of damage to the board is 60%.

6. Recovery through Mi Home (advanced method)

If the standard methods didn’t help, try a forced firmware update via Mi Home:

1. Make sure the latest version of Mi Home is installed on your phone.
2. Connect the camera to the power and hold the reset button for 10 seconds (until double squeak).
3. In the app, select "Add device → Camera → Your model → Restore firmware".
4. Follow the instructions on the screen. It can take up to 20 minutes.

If the recovery was delayed during the "Connect to the camera" stage:

• 📶 Switch your phone to the mobile Internet (sometimes Wi-Fi interferes with the process).
• 🔄 Reboot the router.
• 📵 Make sure the camera is no further than 2 meters from the phone.

💡

Forced firmware recovery removes all camera settings, including account binding, and you'll have to reconfigure the device after the procedure.

7. When to contact the service

If none of the methods worked, it may be a hardware problem. Contact Xiaomi Service Center if:

• 💥 The camera smells like a burn or there is a darkening on the board.
• 🔌 The indicator does not light up even after replacing the power supply.
• 🔊 The camera emits repeated clicks (a sign of capacitors malfunctioning).
• 📹 The lens is not focused or the image is blurry (problem with the camera module).

The cost of repairs in official Xiaomi services (for 2026):

⚠️ Attention: Unofficial service centers often use unoriginal parts, which can lead to repeated breakdowns!

FAQ: Frequent questions about including Xiaomi soapbox