Replacement of the screen with Xiaomi Mi Band 6: a complete guide with photos and tips

The Xiaomi Mi Band 6 fitness bracelet has become one of the most popular wearables thanks to its combination of functionality and affordable price. AMOLED-The screen is vulnerable to mechanical damage: falls, bumps, or even pressing hard can cause cracks, broken pixels, or a complete failure of the display. If your bracelet stopped displaying information, shows artifacts, or reacts to late touches, you most likely need to change the screen.

In this article, we will discuss how to replace the display on the Mi Band 6 in the home, what tools you will need, how to carefully disassemble the case, avoid damage to the plumes, and how to install the new screen correctly. We will also give recommendations for selecting parts, testing after repair and eliminating typical errors. Note: the procedure requires accuracy and patience, but with the right approach, even a beginner can cope in 30-40 minutes.

Preparation for replacement: tools and spare parts

Before you start repairing, make sure you have everything you need, and using the wrong tools can damage the board or the body of the bracelet, so don't skimp on quality.

• 🔧 A set of plastic mediators (or guitar mediators) to gently open the body.
• 🔨 Thin screwdriver cross (PH00) — mount-roller.
• 🧲 Magnetic mat or container – so as not to lose small parts (screws, springs).
• 🔍 Lupe or magnifying glass - for working with small connectors and plumes.
• 🧴 Isopropyl alcohol (90%+) Cotton swabs - to clean contacts.
• 🔋 New screen for Mi Band 6 – Buy only from trusted sellers (see section below).

Important: Don't use knives or sharp objects to open the case, it's almost guaranteed to damage the plastic latches. If you don't have experience with small electronics, practice on an old or non-working bracelet.

How to choose a quality screen to replace

Part quality is responsible for 80% of repair success, and there are three types of screens on the market for the Mi Band 6:

1. Original (OEM) — Removed from donor bracelets, fully compatible, but expensive and rare.
2. High quality copies are produced in the same factories as the originals, but without the Xiaomi logo. Price is 2-3 times lower, quality is close to the original.
3. Cheap replicas — often have problems with color reproduction, touch sensitivity, or backlighting, and can last from a week to several months.

Recommended sellers (according to reviews of 2026):

• 🛒 Xiaomi Mi Store Official, Mi Band Parts Pro, Smart Wearables DIY.
• 🛒 Local stores: search for a rating above 4.8 and reviews from a photo of the installed screen.
• 🚫 Avoid sellers without a photo of a real product or with prices lower $5 is almost always marriage.

Critical: Make sure that the screen comes with a new adhesive layer (or double-sided scotch) without which the new display will not fit tightly to the body, which will lead to dust and moisture.

Step-by-step: disassembly Xiaomi Mi Band 6

Now, to the most important step, the disassembly of the bracelet, follow the instructions carefully so that you do not damage the plumes or contacts.

Disable the bracelet from the Mi Fitness app|Charge the battery to 30-50%|Prepare a workplace with good lighting|Take a picture of the bracelet from all sides in case you forget the assembly order.-->

Step 1: Removal of the strap and back cover

1. Remove the strap, pulling it away from the body (it is attached to the latches).
2. Take a plastic mediator and gently insert it into the gap between the front panel and the back cover. Start at any angle and slowly drive the mediator around the perimeter, separating the latches.
3. If the cover does not lend itself, slightly heat the bracelet with a hair dryer (temperature not higher than 60).°C. This will soften the glue.

Step 2: Battery disconnection

When you remove the lid, you'll see the battery glued to the board. Don't pull it by force! Carefully put a plastic blade on the battery, preheat it with a hair dryer (if the glue is too strong), disconnect the battery plume from the board, it's attached with a small connector that you need to plug up.

⚠️ Warning: Do not touch the battery contacts with metal objects, this can cause a short circuit. If the battery is swelling, do not try to restore it: replace it with a new one.

Step 3: Removing the board and screen

1. Unscrew two screws fastening the board to the body (they can be under the seals - gently prick them with a needle).
2. Disconnect the screen plume from the board. It's locked by a latch -- lift it up, then pull out the plume.
3. So you take the board out carefully and put it aside, and you can take the old screen down by using the mediator.

Installation of a new screen and assembly of the bracelet

When the old screen is removed, we start installing a new one, which requires special care, because improper connection of the plume can lead to no image or sensory failures.

Step 1: Prepare a new screen

• Remove the protective film from the inside of the screen (if any).
• If the kit comes with duct tape, glue it to the back of the display. If not, use a thin double-sided tape (no more than 0.2 mm thick).
• Clean the contacts of the plume with isopropyl alcohol and cotton swab.

Step 2: Connecting the plume

Carefully insert the new screen plume into the circuit board connector. Make sure it sits to the end, then lock the latch. Don't put too much effort -- if the plume doesn't come in, make sure it doesn't flip.

Step 3: Installation of board and battery

1. Place the board back in the case and secure it with screws.
2. Connect the battery plume to the board, make sure the contacts are not closed.
3. Stick the battery in its place (use a new glue or double-sided tape).

Step 4: Assembly of the body

Set the new screen into the grooves of the case, then gently press the back cover, snapping it around the perimeter. Start at the corners and gradually move towards the center. If the lid does not sit tight, check if the plume or board is disturbing.

💡

Before you finalize, turn on the bracelet and check the screen, and if you have an image but the sensor doesn't respond, it's likely that the plume isn't fully connected.

Testing after screen replacement

After assembly, you need to check all the functions of the bracelet to make sure the repair is successful.

• 📱 Display: Turn on the bracelet, a welcome image should appear, check the brightness and uniformity of the backlight (whether there are dark spots).
• 👆 Sensor: swipe across the screen, check all gestures (up/down swipes, left/right, tap).
• 🔋 Charging: connect the bracelet to the charger - the charging indicator should appear.
• 📶 Sync: Connect to the Mi Fitness app and check the data transfer (steps, pulse, notifications).
• 💧 Waterproof: if the bracelet supports 5 ATM, check the tightness by dipping it into the water for 1-2 minutes (without sudden movements).

If something's not working:

• 🔄 Screen not turning on: check the plume and battery connection.
• 🖥️ Artifacts on display: it could be a defect in a new screen or damage to a plume.
• 🚫 Sensor does not respond: clean the contacts of the plume with alcohol or check if it is not bent.

⚠️ Warning: If the screen is working after the replacement, but the bracelet discharges quickly, check if the battery contact is closed somewhere).

Common Mistakes and How to Avoid Them

Even experienced wizards sometimes make mistakes when replacing the screen with the Mi Band 6, and here are the most common problems and ways to prevent them:

💡

The most common mistake is to damage the screen plume when you're extracting it, so if you feel resistance, don't pull it by force: heat it up with a hair dryer or drip it under the plume to dissolve the glue.

Another common problem is getting dust under the screen, which not only damages the look, but can also cause a circuit to close.

• Work in a clean, well-lit room.
• Use an antistatic mat or at least a clean cloth under the bracelet.
• Before installing a new screen, wipe the inside of the case with a lilaless napkin.

Alternative repair methods

If replacing the screen seems too difficult or you are not confident in your abilities, consider alternative options:

• 🔧 Contacting the service center: official repairs will cost $15–$30, but you get a warranty. Minus - long wait (from 1 week).
• 🛠️ Purchase of used bracelet for spare parts: on Avito or OLX They often sell Mi Band 6 with a broken screen, but a work fee. $5–$10 and use as a donor.
• 📱 Use without screen: if the bracelet is turned on and vibrating, it can be used for call notifications and pedometers by plugging into the phone.
• ⚡ Upgrade to a new model: If your Mi Band 6 is older than 2 years, it may make sense to buy a Mi Band 8 or Smart Band 7 Pro – they are cheaper than repairing an old model.

FAQ: Frequent questions about screen replacement