How to carefully remove the video recorder Xiaomi from glass: 5 proven ways

Xiaomi video recorders are a popular solution for fixing the traffic situation, but sooner or later there is a need to remove them: to transfer to another car, replace the model or clean the glass. The main problem is the adhesive base of the attachment, which eventually "sticks" to the surface, risking leaving traces or damaging the device itself. In this article, we will discuss 5 safe dismantling methods suitable for Xiaomi models. 70Mai Pro, MiVue 798, Xiaomi Dash Cam 1S And others, and how to avoid common mistakes.

It is important to understand: the method of removal depends on the type of fastening (3M, silicone, magnetic, and lifespan, like a recorder standing in the sun 2.+ And this year, it's going to take a different approach than the device that was installed a few months ago, and we've tested all the methods on real devices, and we've put the data together into a very handy comparison table that will help you choose the best option for your situation.

1.Preparation for dismantling: what to do before removal

Before you start removing, evaluate the condition of the attachment. If the adhesive base has turned yellow, cracked or started to peel off, this is a sign of aging of the glue, and the device can be removed with minimal effort. If the mount looks monolithic to the surface of the glass, you will need preliminary preparation.

Here are the steps before dismantling:

• 📱 Turn off the registrar power to avoid short circuits when manipulating cables.
• 🌡️ Check the temperature in the cabin: optimal - 18-25°C. In the cold, the glue becomes brittle, and in the heat - too elastic.
• 🧴 Prepare means to remove glue residues: alcohol (90%+), White spirits or specialized cleaners (for example, 3M Adhesive Remover).
• 🔧 Pick up tools: plastic mediator (or bank card), toothpick, hair dryer (not construction!), thread or fishing line.

💡

If the recorder is mounted on tinted glass, avoid aggressive solvents, which can damage the film. Use isopropyl alcohol or soap solution.

Pay special attention to the power cable, if it's under the skin or behind the panel, don't pull the wire, it can tear the connector on the recorder, you better first release the mount, and then carefully remove the cable.

Method 1: Heating with a hairdryer - a universal method for "sticky" fasteners

This method is suitable for recorders installed more than 1 year ago, when the glue has time to crystallize. The heat makes it elastic, which makes it easier to remove. It is important to use a household hair dryer (up to 1800 watts), not a construction one - the latter can overheat the plastic of the case.

Step-by-step:

1. Direct the hair dryer to the mount from a distance of 10-15 cm, holding it at an angle of 45°.
2. Heat the area for 2-3 minutes, evenly driving the hair dryer in a circle.
3. Try to put a plastic mediator on the edge of the mount, and if you don't, warm up for another 1 minute.
4. Once the mount has moved, gently pull the recorder parallel to the glass, without tearing off sharply.

Connected dryer with temperature control|

Plastic mediator or bank card|

Gloves (glue can be hot)|

Alcohol to remove glue residues-->

Critical error: do not use metal objects (knives, screwdrivers) to mount the mount, they scratch the glass and can damage the recorder body. If the mounting does not respond even after heating, proceed to the thread method (section 4).

3. Method 2: Use of thread or fishing line - for delicate removal

This method is ideal for recorders with a flat adhesive base (for example, Xiaomi MiVue Juefang or the other two). 70Mai Midrive D06). The line penetrates the mount and cuts off the adhesive layer without damaging the glass. It is important to use a thin nylon line (0.2-0.3 mm) or dental floss (unwashed!).

Algorithm of action:

• 🧵 Cut a piece of fishing line 30-40 cm long.
• 🔍 Carefully push the fishing line under the edge of the attachment, trying to capture as much of the glue layer as possible.
• 🤲 Holding the line at both ends, saw the mount parallel to the glass with forward-back movements".
• 🧼 After removal, remove the remains of the glue with alcohol or white spirit.

The advantage of the method is that it has minimal risk of damage to the glass and the recorder body, but it requires patience, because it can take 10 to 15 minutes to get stuck in the mount, and if the line slides, wet it with water or alcohol a little.

Method 3: Adhesive Solvents – Chemical Approach

For acrylic or silicone adhesive-based fasteners (e.g., complete with Xiaomi) 70Mai Dash Cam 1S) You can use specialized solvents, and they soften the adhesive layer, so you can remove the recorder without any physical effort:

How to apply solvent:

1. Apply the product to the edge of the attachment with a cotton swab or pipette.
2. Wait until the time is set (do not exceed it!).
3. Put a plastic mediator on the mount, and if it doesn't, repeat the application.
4. After removal, wipe the glass and attachment with alcohol to remove solvent residues.

White Spirit|

Isopropyl alcohol|

WD-40|

Specialized tools (3M, Autoglym)|

Another option-->

⚠️ Note: Do not use acetone or solvent 646 - they will damage the tinting of the glass and can dissolve the plastic of the recorder case. 70Mai Night Vision: Avoid getting solvents on the lens.

Method 4: Freezing is an unusual but effective method

This method is suitable for silicone-based fasteners that lose elasticity at low temperatures, and is often used in car service stations to remove stickers and labels, and you will need an aerosol spray with coolant (for example, a spray spray can, CRC Freeze Off) or ice pack.

How to proceed:

• ❄️ Direct the cooler jet to the mount from a distance of 10-15 cm for 10-15 seconds.
• 🕒 Wait 30 seconds – the glue will become brittle.
• 🪛 Put the mount on a mediator. If you don't, re-cool.
• 🧊 Alternative: Apply an ice pack to the mount for 2-3 minutes, then try to remove it.

The advantage of the method is that it is safe for glass and plastic, leaves no traces, but it requires the purchase of a specialized aerosol (cost - from 300%). ₽). Do not use a household freezer - the temperature in it is not low enough for the crystallization of glue.

Method 5: Steam method - for delicate surfaces

If the recorder is mounted on a heated windshield or on a climate-controlled car, steam can be used to soften the glue, a method suitable for models with a thermally sensitive mount (for example, Xiaomi Mi Home Dash Cam).

Instructions:

1. Turn on the windshield heating to the maximum or direct the steam jet from the steam cleaner to the mount.
2. Hold 1-2 minutes - the glue will soften from moisture and heat.
3. Tap the mount with a plastic card, pulling the recorder parallel to the glass.
4. Wipe the surface with a dry cloth, then remove the remnants of the glue with alcohol.

⚠️ Warning: Do not use boiling water - a sharp temperature drop can cause a crack in the glass, especially if it already has chips. The steam should be warm (40-50)°C), not hot.

This method is the safest for tinting, but requires a steam cleaner or a car with a glass heating function. If the steam did not help the first time, combine it with the fishing line method (section 3).

7.What to do after removal: cleaning the glass and fastening

Once the recorder is removed, there will be traces of glue on the glass and mount, and these must be removed to:

• 🚗 Prepare the surface for the new installation.
• 👁️ Avoid glare and clouding of glass.
• 🔄 Keep the mount for reuse (if it is in good condition).

Step-by-step cleaning:

1. Glass: Apply alcohol or white spirit to a microfiber cloth. Wipe the trail in circular motions without pressing hard. Use a plastic scraper (for example, to clean glass) for persistent residues.
2. Fixing the recorder: Immerse it in warm soapy water for 10 minutes. Clean it with an old toothbrush soaked in alcohol. Dry it and check for stickiness -- if the glue has lost its properties, replace it with a new one.

💡

Never use abrasives (such as pumice or hard sponges) – they scratch the glass and spoil the mount. To remove the glue from the plastic case of the recorder, use only alcohol or special wipes for electronics.

If you plan to re-mount the registrar, check the integrity of the adhesive substrate. If it's torn or lost its stickiness, buy a new double-sided tape. 3M 4910 or VHB 4905 – They are optimally suited for auto electronics.

8. Frequent mistakes and how to avoid them

Even with careful removal, you can make mistakes that damage the recorder or the glass. TOP-5 Failures and How to Prevent Them:

If after removal the registrar stopped turning on, check:

• 🔌 Integrity of the power cable – it may have been damaged during dismantling.
• 🔋 Connector condition – inspect it for contamination or deformation.
• 🔄 Reset: sometimes the recorder freezes after mechanical action. To reset, press and hold the Reset button (usually hidden under the lid or next to the Micro-USB connector).

If there are problems, contact the Xiaomi service center – in most cases, the malfunction after dismantling is covered by the warranty (if there was no mechanical damage).

FAQ: Answers to Frequent Questions