The Xiaomi M365 remains one of the most popular vehicles in the city, but even such a reliable device eventually has problems with wheels. Most often, owners have to remove the front wheel to replace the tire, repair the camera or maintain the bearings. However, improper dismantling can lead to damage to the brakes, wires break or deformation of the fork. In this article, we will understand how to remove the front wheel on the Xiaomi M365 without risk to the scooter – taking into account all the technical nuances and typical errors.
It seems simple at first glance, and it's important to consider design features like the disc brake, the axis being fixed with a special left-carved nut and the wheel-connected signal wiring (on ABS models). If you've never repaired a bicycle or scooter, you better prepare the tools and learn the mounting circuitry in advance, and we'll describe each step in detail, from preparation to reverse assembly, and give you tips on how to avoid common problems.
What tools will be needed to remove the wheel
Before you start disassembling, make sure you have everything you need, and not even one tool can make it difficult or impossible to do so. Here's the full list:
- 🔧 Set of hexagons (mandatory with a size of 5 mm - it is needed to weaken the brake caliper).
- 🔨 15 mm carrot key or a cap key of the same size (for unscrewing the axis).
- 🔧 End key with a head of 15 mm (more convenient than carob, as it allows you to put more effort).
- 🛠️ Flat screwdriver (for tweaking protective covers or adjusting the position of brake pads).
- 🧲 Magnet or small container (so as not to lose small details - washers, springs).
- 📸 Smartphone (to photograph the original position of the parts before disassembly).
If you have a Xiaomi M365 Pro or a newer version, check whether the axis diameter is different (sometimes 17 mm instead of the standard 15 mm). Also, a dynamometer key for exact nut tightening when reassembling (the recommended moment is 40-50 Nm).
Preparation of the electric scooter for disassembly
Before you remove the wheel, the scooter must be properly prepared, which will save you from unpleasant surprises like sudden switching on of the engine or damage to the wiring.
⚠️ Warning: Never disassemble a scooter with the battery on! Even if it is not driving, the contacts under voltage can cause a short circuit when the wires are accidentally hit. 🔋 Turn off the scooter with a long press on the power button (5 seconds). 🔌 Disconnect the battery (if you plan to work with wheel wiring). To do this, unscrew the 4 screws on the bottom cover and gently disconnect the connector. 📏 Turn the scooter upside down with wheels, pre-putting soft fabric under the steering wheel and display so as not to scratch. 🧹 Clean the wheel and fork of dirt (especially the axis area) so that the sand does not get into the bearings. If you remove the tire to replace the tire, prepare a new rubber and degreasing agent (such as isopropyl alcohol) in advance - it will help to put the tire on the rim more easily. Also check the condition of the brake disc: if it is deformed or has deep grooves, it should also be replaced. 💡If the axis nut is boiled and does not unscrew, sprinkle it. WD-40 Or a 10 to 15 minute analogue before the disassembly. Don't hit the key with a hammer, it can bend the axle! Step-by-step instruction: how to remove the front wheel Now we move on to the main process. Follow the instructions strictly in steps so that important details are not missed. Relax the brake caliper. With a hexagon, you can unscrew the two bolts that hold the caliper to the fork. Don't remove them completely -- just loosen them so that the caliper moves freely. This is to make sure that after the wheel is removed, the brake pads don't interfere with the axle pulling out. Unscrew the axle nuts. On Xiaomi. M365 The left nut has a reverse (left) thread, which means you have to turn it clockwise to loosen it, the right nut spins counterclockwise, as you normally would. Use the 15mm key and hold the wheel so it doesn't scroll. Remove the washers and pull the axle. After unscrewing the nuts, remove the flat and spring washers (remember their order!). Carefully push the axle out of the fork. If it's tight, tap the key with a plastic hammer or through a wooden pad. Disconnect the wiring (if any). On models with ABS, a speed sensor is connected to the wheel. Disconnect it by pre-picturing the location of the wires. Don't pull the wires - only for the connector! If the wheel can be removed, you can turn the brakes back on the wheel before the ty, you can now apply the brakes. ☑️ Checklist before removing the wheel Is the scooter turned off? Is the battery disconnected (if necessary)? Is the brake caliper weakened?Photos of the initial state are made?Tools at hand?Completed: 0 / 5 Typical mistakes and how to avoid them Even experienced masters sometimes make mistakes when disassembling Xiaomi M365. Here are the most common of them and ways to prevent them: Error Consequences How to avoid Mixed the direction of the thread on the left nut Breaking the thread or jamming the axis Remember: left nut unscrewed clockwise Not loosened brake caliper Pads block the wheel, axle not pulled Always loosen the caliper until nuts are removed Lost spring washer Axis luftite, wheel dangling Use magnet or container for small parts sharply pulled wire ABS Wire break or damage connector Disconnect only for the connector, not for the wires Not cleaned axle from rust Wheel spins tightly, accelerated wear bearings Clean axle with sandpaper before assembly Critical error: attempt to remove the wheel without weakening the brake caliper. This leads to deformation of the brake disc or breakage of the pads. If the wheel doesn't pull out even after the nuts are unscrewed, never use force - check if the disc rests against the pads. What if the axle is jammed?If the axle doesn't pull out even after the nuts are unscrewed, it's most likely rusted to the bearings. In this case: 1. Spray WD-40 2. Wait 10-15 minutes. 3. Knock carefully on the axis through a soft pad (like a wooden bar). 4. Scrolling the wheel back and forth, pulling the axle at the same time. Don't use a metal hammer - it will damage the bearings! Back assembly: The assembly goes backwards, but there are some nuances. The rule is, everything should fall into place without effort. 🔄 Check the position of the brake pads. They should be symmetrically positioned relative to the disc. If the pads are shifted, correct them with a flat screwdriver. 🔧 Set the washers in the correct order. First, flat washer, then spring (convex side to nut). 🔩 Tighten the nuts cross-cross. First, pull the left one slightly, then the right one, then finally tighten both. Push-up time is 40-50 Nm. 🔌 Connect the connector. ABS (Make sure the contacts are clean and the connector is snapped to the end. After assembly, check: The wheel rotates freely, without backlash or extraneous sounds. The brakes work smoothly, without creaking. There are no errors on the scooter display (if you switch off). ABS). ⚠️ Attention: If the wheel is luftite after assembly, it means that the spring washer is installed incorrectly or the nut is not sufficiently tightened! 💡The most common problem after assembly is uneven braking. This is because the brake disc is not properly aligned with the pads, so you can loosen the caliper, press the brake lever to make the pads self-center, and tighten the bolts again. When professional repair is required, not all faults can be repaired by yourself. Here are the best times to contact the service: 🚨 The axle is bent or cracked, and it's a critical malfunction that requires a replacement axle or fork. ⚡ The wiring is damaged. ABS. If the wires are cut or melted, you will need a soldering iron and experience with electronics. 🔧 Bearings have crumbled or jammed, and replacing them requires special equipment and skills. 🛑 The brake caliper is deformed. Attempting to straighten it yourself usually leads to a deterioration in braking.The cost of professional front wheel repairs on Xiaomi M365 2026: Replacement of the tire - from 800 to 1500 ₽. Replacement of bearings – from 1200 to 2000 ₽. Repair of the brake system - from 1500 to 3000 ₽. Replacement of an axle or fork - from 3000 ₽ (If you're not confident, it's better to pay for repairs than risk safety, for example, misplaced bearings can jam at speed, and poorly adjusted brakes can increase braking distance several times. FAQ: Frequent questions about removing the wheel on Xiaomi M365 Can you remove a wheel without a hexagon by 5 mm? Theoretically, yes, but it's very inconvenient. You can try using a flat screwdriver, but the risk of ripping off the caliper bolts is very high. A hexagon by 5 mm is a must-have tool for this model. If it's not available, you'd better buy it (it's inexpensive). What if the wheel is rubbing against the fork after assembly? That means that the axis is crooked or not fully set. Take the design apart and check: Is the axle inserted exactly (it should come out symmetrically on both sides); Is there a washer skew; Is the nuts properly tightened (are they not pulled on one side); Also, the cause may be a deformed brake disc - check it visually. Do you need to lubricate the axle when assembly? Yes, but only with a special bearing lubricant (for example, Liqui Moly LM 50). Do not use WD-40, solidol or litol - they attract dirt and quickly check the moist disc at a distance of 1, 000 km, if the tire is covered at the front of the wheel at the front of the wheel is cut every time every year. - you need to be covered with a slashing time at the front of the wheel at the interval of the wheel at the front of the wheel at the same time. Is it okay to drive with a backlash in the front wheel? Absolutely not! The backlash in the wheel leads to: Uneven wear of the tire; deterioration of handling (the scooter can wag); risk of jamming the wheel at speed; damage to the fork or axle; if you find a backlash, immediately stop operation and eliminate the cause (usually a weakened nut or worn bearings).