How to remove the lid from the phone Xiaomi Redmi 9A

Disassembling a modern smartphone is a delicate process that requires not only special tools, but also a deep understanding of the design of the device. Xiaomi Redmi 9A, despite its availability and popularity, has a single body, which the manufacturer assembles using powerful adhesive compounds. This is done to improve the strength and protect the internal components from dust, but if necessary, this design creates serious difficulties for the master.

Before you start dismantling, you need to be aware of the risks: self-opening the case automatically voids the manufacturer's warranty. If your device is in warranty service, it is better to contact an authorized service center. However, if the warranty period has expired or there are damages that are not subject to warranty, careful disassembly at home is quite possible with the observance of technology.

In this article, we will take a closer look at the Redmi 9A’s rear panel removal process, focusing on adhesive softening techniques and safely detaching plumes. Mistakes can cause a touchscreen plume to rupture, battery damage, or chips on glass, so carefully study each step before work begins.

Tools and workplace preparation required

The quality of the work is directly dependent on preparation. You'll need a specialized toolkit, because common household items like knives or pins can cause irreparable damage to the plastic case and the inner boards, the main tool being a medical scalpel or a thin metal mediator that allows you to carefully cut through the adhesive layer.

Besides cutting tools, it's critical to have a heat source. The glue that holds the lid is a thermoset polymer that softens at about 80-90 degrees Celsius. Professional thermophene is ideal, but you can use a quality induction heating pad or even a hair dryer at home, although the latter is less effective and takes longer.

• 🔧 Precision screwdrivers (cross-haired) P2/P000) screw-off.
• 🌡️ Thermal source (thermophene, heating pad or hair dryer) for heating glue.
• 🧤 Thin mediator or blade for cutting the adhesive layer.
• 🔋 Suction cup for the primary lifting of the cover (optional).
• 🧴 Isopropyl alcohol or special liquid B-7000 glue-residue.

⚠️ Warning: Never use an open flame or a building hair dryer at maximum settings without temperature control.Overheating can warp the plastic frame of the housing or damage the display matrix if heat is transferred too intensively.

Prepare the workspace: it should be well lit and free of unnecessary items. It is recommended to use an antistatic mat or just a clean, dry surface so that small screws do not get lost. Also take care of the mounting triage tanks in advance, since the Xiaomi Redmi 9A uses screws of different lengths, and their entanglement can damage the thread or board.

The process of heating and primary opening of the body

The most important step in determining the success of the entire operation is the correct heating of the device perimeter. The adhesive layer in Xiaomi budget models is often unevenly applied, so you need to warm up the entire area of the rear panel, paying special attention to the edges. Put the phone down on the soft fabric or silicone mat to avoid scratching the display, and turn on the heating element.

The optimal warm-up time is between 3 and 5 minutes, depending on the power of your tool. Periodically check the temperature of the back side with your hand - it should become noticeably hot, but not burning. If the body becomes too hot, let it cool down a little so as not to damage internal components, such as the battery, which is sensitive to overheating.

After enough warming up, take a suction cup, glue it to the bottom of the back cover, and pull it up slightly, creating a small gap. If there's no suction cup, you can carefully use a thin blade by inserting it into a connector for the suction cup. SIM-You have to use a card or a microphone hole, but you have to be very careful, and your goal is to create a minimum gap in the air. 1-2 millimeter, which then enters the mediator.

Once a gap has appeared, insert a mediator or a thin blade into it. Don't try to remove the lid immediately; instead, use the tool along the perimeter, cutting the softened glue. The movements should be smooth, without jerking. If you feel strong resistance, stop and warm up the area again - the force is not here, it will only lead to the breakdown of the plastic.

Safety technique for the rear panel

The process of separating the lid in the Redmi 9A is complicated by the presence of a fingerprint scanner plume (in some versions) or simply a tight fit of plastic. As you move around the perimeter, try to keep the tool parallel to the plane of the body, swaying it slightly from side to side, which will help effectively destroy the adhesive structure without leaving islets of glue that can prevent full removal.

Pay special attention to the corners of the device. It's in these areas where the glue often freezes most tightly, and the plastic has complex geometry. Carefully work through each corner, making sure that the tool has gone completely in a circle, and only after you've made sure that there's no resistance around the perimeter, you can start the final removal of the panel.

⚠️ Note: In some revisions Xiaomi Redmi 9A There may be a plume running to the main board under the back cover, and a sharp jig of the lid upwards is guaranteed to cause the plume to break, requiring expensive replacement of the module or soldering.

When the lid is completely free of glue, don't put it down. Carefully raise one of the lower corners and visually inspect the interior for the connection plumes. If there are no, you can safely remove the panel. If the plume is present, it must be detached by unlocking the connector lock beforehand.

Working with internal components and plumes

When you take the back cover off, you see the inside of the smartphone, and you have the battery in the main, and you have a motherboard in the top, and you have a plastic pad, and you have to take that plastic protection off to access most of the components, including the display connectors and the battery.

The plastic pad is attached with several screws, which are usually hidden under stickers or marked. Use a magnetic screwdriver of the right size to unscrew them. Once the protection is removed, access to the main board where the connectors are located will be opened. Be extremely careful: the plumes in this model are very thin and fragile.

To turn off the plumes, for example, if you change a display or battery, you need to use a plastic blade. Metal tools can damage the contact paths on the board. Carefully tuck the connector and remove it from the connector. If the connector has a locking frame, it must first bend or lift, depending on the design.

If your goal is to replace the battery, remember that in the Redmi 9A it is also planted on double-sided tape. Removing it will require reheating and carefully, using a plastic card or fishing line, cut out the old cell. Never try to tamper with a screwdriver or knife - a puncture of the lithium-ion battery can cause fire.

Device assembly and elimination

The phone is assembled in reverse order, but with important adjustments. The old adhesive layer must be completely removed from the frame of the body and the back cover itself. Use isopropyl alcohol and soft rags to clean the surfaces to the perfect state. The residues of the old adhesive will not give new fixation and can lead to a backlash of the case.

For secure fixation, use a special electronics sealant (e.g., B-7000) or pre-prepared adhesive tapes cut into the shape of the frame. Apply the adhesive in a thin layer, avoiding getting into the internal components, the camera and the speakers. Once the body parts are connected, it is recommended to lock the phone with rubber harnesses for 15-20 minutes for primary polymerization of the adhesive.

As you twist the screws, watch for the force. The plastic used in Xiaomi is quite soft, and excessive force can break the thread or crack the rack. Twisting the screws cross-cross, evenly pressing the board against the case. This is especially important to prevent microflexes of the board, which can eventually lead to chip dumps.

Common mistakes in the Redmi 9A disassembly

One of the most common mistakes is ignoring the heat: trying to remove the lid cold or after not warming up almost always ends in cracks in the back panel, the plastic becomes brittle when mechanically exposed if the glue is not softened to a state of jelly.

Another mistake is using metal tools to snap plastic latches inside the case. Metal leaves bullies and can close contacts on the board, which will short circuit when turned on. Always use dielectric materials such as plastic or special antistatic blades.

• 🚫 Attempt to lid in the center, and not around the perimeter, which leads to its breakage.
• 🚫 Forgetting to shut down the battery before working with other plumes.
• 🚫 Use of aggressive solvents (acetone) that melt the plastic of the case.

⚠️ Warning: When assembled, make sure all screws are twisted. The absence of even one screw can lead to creaks, dust getting inside and, in rare cases, disruption of antenna modules, since screws often serve as grounding elements.

Also, the masters often forget to clear the dynamic speaker grid and the auditory speaker from the dust that opens when the lid is removed. This is a great moment for preventive cleaning, which will improve the volume of the sound. Use a soft brush and a little alcohol to clean these areas.

💡

Keep all the screws in the order you twisted them. In the Xiaomi Redmi 9A, the screws can differ by only 0.5 mm in length, but screwing a long screw into a short hole can punch through the board.

Frequently Asked Questions (FAQ)

💡

The key to success in dismantling the Redmi 9A is patience and quality warming of the glue. Do not force the events, and the body will remain intact.