How to remove the back cover on Xiaomi Redmi Go: instructions with photos and tips

Xiaomi Redmi Go is a budget smartphone that, despite its simplicity, requires caution when disassembling. Many owners face the need to remove the back cover, whether it be replacing the battery, cleaning from dust or repairing plumes. But the wrong approach can lead to cracks in plastic, damage latches or even failure of internal components.

In this article, we'll take a look at the whole process, from tool preparation to final assembly, and you'll learn what key mistakes beginners make, how to avoid breakages and what to do if the lid doesn't respond, and you'll focus on safety: why you can't use a knife or a screwdriver, how to heat the case properly, and where the most vulnerable latches are located.

The material will be useful both for those who are first taking up the dismantling, and for experienced users looking for nuances for the Redmi Go model. All recommendations are based on the repair practice and official Xiaomi service manuals.

Preparation for disassembly: tools and conditions

Before you start removing the lid, make sure you have everything you need, and not even one tool can turn a simple procedure into a nightmare with broken latches.

Here is the minimum set you will need:

• 🔧 Plastic mediators (2-3 Pc. - it is better to take a set with different thicknesses (0.1–0.3 Metal tools are prohibited!
• 🔥 Hair dryer or thermo-air station for softening the glue. Optimal temperature: 60-70°C.
• 🧲 Suction cups (2 pcs) - help to evenly pull the cover after heating.
• 📦 Container for screws – in Redmi Go they are few, but easy to lose.
• 🧴 Isopropyl alcohol (90%+) — glue-cleaner.

Also prepare the workplace:

• 🪑 A table with good lighting (better to use a table lamp).
• 🧹 Clean surface without debris – getting dust under the lid can cause creaks.
• ⚡ The socket is nearby if you use a hair dryer (the wire should not interfere with the wire).

Critically, before disassembling, completely discharge the battery to 0% and leave the smartphone off for 10-15 minutes, which minimizes the risk of short circuit in case of accidental contact with the board.

Step-by-step: how to remove the cover without damage

Now, to the process itself, follow the instructions strictly by step, and skipping a stage can cause the latches to break.

Step 1. Heat the body.

The glue that glues the lid to becomes elastic when heated. Turn the dryer on to the minimum power and evenly warm the back panel for 2-3 minutes, holding it at a distance of 10-15 cm. Pay special attention to the edges - there is the glue most.

Important: Don't overheat! Temperatures above 80°C can warp plastic or damage the battery.

Step 2. Unplug the cover

After heating, start removing immediately. Use suction cups:

1. Attach one suction cup to the bottom of the lid (above the Redmi logo).
2. The second is closer to the upper edge (above the camera).
3. Pull up carefully, creating a uniform effort.

If the lid doesn't lend itself, don't force it.

• 🔄 Repeat heating for another 1-2 minutes.
• 🪛 Insert a plastic mediator into the slot and gently run them around the perimeter, separating the glue.

Step 3: Latching work

In Redmi Go, the cover is attached not only to glue, but also to 6 plastic latches:

• 2 on the sides (near the volume buttons).
• 2 in the upper part (near the headphone jack).
• 2 in the lower (near the charging connector).

Use the mediator to gently snap them one at a time. If you hear a crunch, it breaks the latch! Stop and double-check the angle of the instrument.

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes that lead to breakdowns.

Another common problem is that the plumes are not fully disconnected. In Redmi Go, the battery plume is short and fragile. If you pull the lid too hard, it can come off the board. Always check if something is disturbing the removal!

What to do after removing the lid: maintenance tips

When the lid is finally removed, do not rush to start repairing immediately.

• 🔋 Check the battery for bloating. If it's deformed, don't turn on the phone until you replace it!
• 📸 Clean the camera module of dust with a dry brush or a can of compressed air.
• 🔊 Blow the headphone jack – often there accumulates dirt, causing problems with sound.
• 🛠️ If you plan to replace parts, take a picture of the location of the plumes before disconnecting.

To clean the board from dust, use a soft brush (for example, for drawing) and isopropyl alcohol. In any case, do not blow with your mouth - moisture from breathing can cause corrosion of contacts.

If your goal is to replace the battery, consider that in Redmi Go it is glued to the body with double-sided tape. To remove it without damage, gently tuck the edge with a plastic spatula and pull on a special black tape (if any).

💡

Before assembly, wipe the edges of the lid and body with alcohol - this will remove the remains of the glue and provide a tighter fit.

How to assemble the smartphone back: nuances

Assembling often raises more questions than disassembling. Here are the key points for Redmi Go:

1. Check the latches: Before you install the lid, make sure that all 6 latches are in place and not damaged. Broken ones can be replaced with similar ones from the donor cases.
2. Glue: If the original adhesive has lost its properties, use a thin layer of B-7000 around the perimeter of the lid. Apply point-by-point, avoiding the speaker and microphone area.
3. Press evenly: after installing the lid, put the smartphone under the load (for example, a book) for 10-15 minutes so that the glue catches.
4. Test: Before final assembly, turn on your phone and check all buttons, cameras and speaker.

If after assembly the cover creaks or fits loosely, the reasons may be as follows:

• 🧴 Not enough glue - add a little around the edges.
• 🔧 Not clicked clips - disassemble and repeat the assembly.
• 📱 Dust fell - clean the edges with alcohol.

💡

When you build it, never push the center of the lid, it can damage the display module. The effort should be distributed around the edges!

When is the best time to contact the service

Not all breakdowns can be repaired by yourself.

• 💥 After the fall, the touchscreen does not work or the display shows artifacts (possibly the plume has gone away or the matrix has cracked).
• 🔋 The battery is swelling or leaking - it is dangerous to health!
• 📡 The antenna is not working (no network) – the problem may be damage RF-cable.
• 🔧 The latch of the body is broken, and the lid is not fixed even after gluing.

The average cost of dismantling Redmi Go in the service is 500-800 rubles (2026). If you need to replace the battery or plume, the price will rise to 1,500-2,500 rubles depending on the part.

Before you take the phone to the shop, check if the warranty period has expired. If the smartphone is warranty, disassembling it yourself will cancel it!

Alternative methods of removing the cover (for experienced)

If the standard method doesn't work, you can try alternative methods, but they require experience and carry risks.

Method 1: Use of thread

A thin capron thread (like a guitar string) can help cut the glue, stick it under the lid at one of the corners, and gently saw back and forth while pulling the lid up, and risk damaging the plumes if the thread slips.

Method 2: Softening of glue with alcohol

Apply isopropyl alcohol (90%+) around the perimeter of the lid with a needleless syringe. Wait 5-10 minutes - the glue will soften. Risk: alcohol can get on the board and cause corrosion if you do not dry the phone after disassembly.

Method 3: Vacuum pump

Special pumps for disassembling phones create uniform vacuum pressure, which helps remove the lid without mediators. Risk: expensive equipment, and if used improperly, you can deform the body.

⚠️ Warning: Alternative methods should only be used if the standard technique with a hair dryer and mediators has not worked, and in 90% of cases they are unnecessary and only increase the risk of failure.

FAQ: Frequent questions about the Xiaomi Redmi Go disassembly