How to remove the screen on your phone Xiaomi: instructions with photos and videos

Introduction: When you need to take your screen off on Xiaomi

Xiaomi's smartphone screen is one of the most vulnerable parts of the device. Cracks, broken pixels, a broken touchscreen or a blurred image make users think about replacing the display. But before carrying the phone to the service center, many decide to try to remove the screen themselves. This is justified if you are confident in yourself and willing to take the risk that improper dismantling can damage the plumes, battery or motherboard.

In this article, we will discuss in detail how to remove the screen on Xiaomi phones of different series (Redmi, POCO, Mi, what tools you need, what pitfalls await beginners and how to avoid typical mistakes, and you will learn in which cases it is better not to take risks and turn to professionals, immediately warn: the procedure requires patience, accuracy and at least minimal experience with electronics. If you’ve never taken a smartphone apart, practice on an old device or watch video instructions before you start work.

It is important to understand that the screen design on Xiaomi depends on the model. For example, in the Redmi Note 10 Pro, the display is glued to the frame, and in Xiaomi, the display is glued to the frame. 12T — This affects the complexity of the dismantling and the toolkit. We'll look at the generic steps, but for a particular model, we recommend looking for detailed guides or disassemblies on YouTube.

What tools will be needed to take the screen

Without the right tools, it’s almost impossible to get a screen on Xiaomi. Here’s the minimum set you’ll need:

• 🔧 Plastic blades (mediators) - for neat smearing of the body and disconnecting clips. Metal tools can scratch the frame or damage the plumes.
• 🔥 A hair dryer or a thermo-air station to soften the glue that the screen is glued to the body. Optimal temperature: 60-80°C (don't overheat!).
• 🧲 Screen suction cup - helps to pull the display evenly after heating.
• ⚙️ Screwdriver cross (PH00 or PH0) — Some Xiaomi models use screws like this. Y00 or T3.
• 📦 Tweezers and antistatic bracelet – for working with small details and protection from static electricity.
• 🧴 Isopropyl alcohol (90%+) and napkins without pile - for cleaning glue residues and contacts.
• 🔋 New glue (bilateral scotch or liquid glue) B-7000) — If you plan to re-add the screen.

Also, prepare your workspace: a clean desk with good lighting, an antistatic mat (if any) and screw containers, they're easy to lose. Don't work on a carpet or a sofa: static electricity can damage the motherboard. If you don't have experience, buy a repair kit for a particular model, it will already have all the necessary tools and glue.

⚠️ Warning: Never use a knife or other sharp metal objects to smack the screen! This is almost guaranteed to damage the plumes or cut the battery.

Preparing the phone for disassembly: important steps

Before you start taking the screen, you need to properly prepare the phone, and skipping these steps can lead to data loss, damage to the device, or even injuries.

1. Turn off the phone and remove it. SIM-card and memory card (if installed) this will prevent short circuit and data loss.
2. Discharge the battery to 25-50%, a fully charged battery is more dangerous if accidental damage occurs.
3. Back up your data. Even if you're confident in what you're doing, there's always a risk that your phone won't turn on. Use Mi Cloud or connect your device to your PC.
4. Heat the screen with a hair dryer around the perimeter for 2-3 minutes. Keep the hair dryer at a distance of 5-10 cm so that the display does not overheat. The glue should become soft, but not liquid.

If you're taking a screen because of cracks, stick tape over it so that the shrapnel doesn't break apart and hurt you, and we recommend wearing gloves to protect your hands from cuts and reduce the risk of leaving prints on the inside.

Turn off the phone and remove it. SIM-map|Discharge the battery to 25-50%|Make a backup copy of the data|Heat the screen with a hair dryer around the perimeter|Plug Scotch on a cracked display (if there are cracks)|Prepare a workplace with good lighting-->

If your Xiaomi has a degree of protection IP53 or higher (e.g. Xiaomi 13 Pro or Redmi Note 12 Pro)+), Be careful with sealing pads, and if they are damaged, they will cause you to lose water resistance, and in such cases, after repair, you may need to replace the pads or apply a special sealant.

Step-by-step: how to remove the screen on Xiaomi

Now, we'll go through the process. We'll describe a generic method that works for most Xiaomi models (e.g., Redmi Note 11, POCO X3 Pro, Mi 11 Lite) For specific devices (e.g. foldable Xiaomi devices) MIX Fold or curved screen models) look for individual guides.

Step 1: Remove the back cover (if required)

On some models (e.g. Xiaomi) 12S Ultra) screen is removed from the front, but most often you need to remove the back cover first:

1. Heat the back panel with a hairdryer (especially at the edges).
2. Insert the plastic blade into the gap between the lid and the frame (usually start at the lower corner where the connectors are located).
3. Carefully swipe the perimeter with your shoulder blade, snapping the clips.

Step 2: Unscrewing screws and disconnecting plumes

When you take the back cover off, you'll see the motherboard and the battery.

1. Unscrew all the screws that hold the metal plate above the battery (usually 4-6).
2. Carefully disconnect the battery plumes, the screen and other modules. Use a plastic blade to plug the connectors. Don't pull the wires!
3. If the battery is swelling, do not try to puncture or bend it, this can lead to fire, in which case it is better to contact the service.

Step 3: Heating and removing the screen

Now we come to the most important stage:

1. Warm up the screen with a hair dryer (1-2 minutes), especially at the edges.
2. Stick the suction cup to the bottom of the display (where the charging connector is usually located).
3. Pull the suction cup up with uniform force. If the screen doesn't respond, heat it up again.
4. As soon as the gap appears, insert a plastic spatula into it and slowly swipe around the perimeter, separating the glue.

In some models (for example, POCO F3) The screen can be further fixed with clips. If you feel resistance, don't pull harder, look for mounts.

Step 4: Disconnect the screen plume

And when you take off the screen, you'll see a plume connecting it to the motherboard.

1. Put a black lock on the plume connector (usually it rises up).
2. Remove the plume by pulling it over the edge.
3. If the plume is damaged, it will have to be replaced - without it, the new screen will not work.

At this stage, you can assume that the screen is successfully removed. If you plan to replace it, make sure that the new part is compatible with your Xiaomi model. Original parts are better to buy from official suppliers or trusted sellers (for example, on AliExpress with a high rating).

Common Mistakes and How to Avoid Them

Even experienced craftsmen sometimes make mistakes when taking a screen, and we've collected the most common mistakes and ways to prevent them:

Another common problem is that the flexible plume can break if you bend it or pull it too hard, if the screen doesn't turn on after assembly, or if part of the display doesn't respond to touch, it's probably the plume's fault, and if it does, it'll have to be replaced (costs 500 to 2,000 rubles depending on the model).

⚠️ Warning: If you notice that the battery is swelling after taking off the screen (it will be convex or with characteristic "bubbles"), do not continue repairs. The bloated battery can ignite at the slightest damage. Take the phone to the service or dispose of the battery according to the rules.

💡

If you are screening on a model with AMOLED-With a matrix (such as the Xiaomi 12 Pro or Black Shark 5), be especially careful – such displays are thinner and more fragile than the ones you see on the screen. IPS. Heat them at a lower temperature (up to 60).°C) and avoid pressure on the centre of the screen.

Features of screen removal on popular Xiaomi models

The design of the screen can vary greatly depending on the series and year of release of the smartphone. Let's consider the nuances for the most popular lines:

Redmi Note 10 / 11 / 12 series

The screens in these models are glued to the middle frame, not to the back cover. The main difficulty is thin plumes that are easily damaged.

• 🔧 Use two suction cups: one for the top of the screen, the other for the bottom.
• 🔥 Heat not only around the perimeter, but also the center of the screen (there is also glue there).
• ⚠️ Don’t pull the screen too hard – first separate it on the sides with a spatula.

POCO F3 / F4 / F5

In these smartphones, the screen is attached to clips and glue, and the feature is an additional metal plate under the display, which must be unscrewed before taking off. POCO F3 The plume of the touchscreen and matrix is combined into one, so if damaged, you will have to change both.

Xiaomi 11T / 12T / 13 series

The flagship models have AMOLED-It's a high-pixel density screen with thin glass:

• 🔥 Heat the screen at a temperature not higher than 60°C.
• 🧲 Use a wider suction cup to evenly distribute the pressure.
• 🛠️ Replacing the screen may require the transfer of the fingerprint scanner (on models with in-display sensor).

Xiaomi MIX Fold / MIX 4

Foldable and conceptual models require a professional approach. MIX Fold screen consists of two parts connected by a loop. Self-repair of such devices is not recommended, because there is a high risk of damage to the folding mechanism.

If you're not sure about your model, look up YouTube's video disassembly of your smartphone, for example, a request for "Redmi Note 11 Pro Disassembly Screen" will give detailed instructions with all the nuances.

What to do after removing the screen: install a new display

If you've successfully shot an old screen, it's time to install a new one.

1. Clean the frame of the old glue with isopropyl alcohol. Do not use acetone or solvents - they can damage the plastic.
2. Check the new screen for defects (scratches, broken pixels) and connect it to your phone before the final installation to make sure it works.
3. Apply a new glue. We can use it: 📏 Double-sided scotch (e.g., double-sided scotch, 3M VHB) — easier to use, but less reliable. 🧴 Liquid glue (B-7000 or LOCA) — It requires experience but provides better fixation.

Set the screen up.

Secure the clips.

Connect the battery.

If the screen does not work after installation, check:

• 🔌 Is the sleeve properly connected (sometimes it can jump out of the connector).
• 🔋 Is there enough charge in the battery (plug the charge).
• 🛠️ Is there any damage to the plume or the connector of the motherboard.

⚠️ Note: If you have replaced the screen with Xiaomi AMOLED-The color matrix looks dim or distorted, perhaps the calibration profile was not transferred, in some models (for example, Xiaomi 12 Pro), it is stored in the memory of the old screen, in which case you may need to program configuration through Fastboot or specialized software.

💡

If you are replacing the screen on models with Always On Display (such as Xiaomi 13 Ultra), you may need to reset the screen settings in the Settings menu after installing the new display. → Display. Otherwise, the function may not work properly.

When it is better to contact the service: signs of complex repairs

Not all screen failures can be repaired by yourself, but here are some cases where you can trust the professionals:

• 💥 A cracked matrix with leaking liquid crystals (visible as dark spots, stains) requires a complete replacement of the display module and special equipment.
• 🔥 Bloated or damaged battery, the risk of fire is too high.
• 🛠️ Damage to the plume or connector on the motherboard, it would require ration, which without experience, you can't do.
• 📱 Models with complex design (Xiaomi) MIX Fold, Black Shark with active cooling).
• 🔒 Smartphones with bootloader lock. After changing the screen, you may need to unlock through Mi Account.

The cost of replacing the screen in the service varies from 3000 to 15 000 rubles depending on the model.

• Redmi 9A — 3 000–5 000 ₽ (The screens are cheap, but the work costs almost as much).
• POCO X3 Pro — 5 000–7 000 ₽.
• Xiaomi 12 Pro — 10 000–15 000 ₽ (because AMOLED and fingerprint scanner).

If you doubt your own abilities, compare the cost of self-repair (screen). + tool + The risk of a service is sometimes small, and the guarantee of a service center is worth it.

FAQ: Frequent questions about screen-taking on Xiaomi