Xiaomi Redmi Note 8 Pro is one of the most popular smartphones in the budget segment, but its screen, like any device, is not immune to cracks, broken pixels or problems with the touchscreen. If you decide to replace the display yourself, it is important to understand that improper dismantling can lead to damage to the plumes, detachment of the sensor or even failure of the motherboard. In this article, we will understand how to remove the display of the Redmi Note 8 Pro without consequences, what tools you will need and what to pay attention to in the process.
The procedure requires care and patience. Unlike Xiaomi's flagship models, where the screen is often attached to double-sided tape, the Note 8 Pro uses a combination of glue and latches, which makes it difficult to do. In addition, the display hides fragile battery and camera plumes - they are easy to damage if you carelessly move. If you have never taken your smartphone apart, we recommend you first practice on a non-functional device or watch video disassembly from experienced craftsmen.
Before you start, evaluate your strength: screen repair Redmi Note 8 Pro is a category of medium difficulty. If you are not sure about your skills, it is better to contact the service center. However, with the right approach and the necessary tools, the task is quite feasible at home.
Preparation for dismantling: tools and materials
To remove the display Xiaomi Redmi Note 8 Pro, you need a specialized set of tools. Don't try to do with the tools at hand, it can damage the body or internal components.
- 🔧 Plastic blades (mediators) - for tidying the body and detaching the latches. Metal tools should not be used!
- 🔥 A hair dryer or thermo-air station to soften the glue that the screen is glued to the frame. Optimal temperature: 60-80°C.
- 🧲 Screen suction cup - will help to evenly raise the display after heating.
- ⚡ Screwdriver. T3 and T5 — for unscrewing screws holding the metal frame and plumes.
- 📦 Tape for fixing plumes - so as not to lose small parts and not confuse them during reverse assembly.
- 🧴 Isopropyl alcohol (90%+) — for cleaning glue residues and degreasing surfaces.
- 🛡️ Protective gloves and glasses – glue and glass shards can be dangerous.
Also, prepare your workspace: it should be clean, well-lit and draft-free. Work on a soft-backed table (like a silicone mat) so you don't scratch your smartphone. If you don't have soldering experience, buy a new double-sided tape to lock the screen in advance, the original glue loses its properties after dismantling.
⚠️ Warning: Do not use a household hair dryer at maximum power! hot air flow can melt plastic body elements or damage the battery. Keep the hair dryer 5-7 cm away from the smartphone and move it constantly to avoid local overheating.
Step-by-step instructions: how to remove the display
Before starting work completely turn off the smartphone and remove SIM-If the battery is swelled or deformed, removing the screen can be dangerous, in which case it is better to contact the professionals:
- Heat the body. Turn the dryer on at medium power and evenly warm the edges of the screen for 2-3 minutes. Pay special attention to the bottom where the plumes are located. The glue should be soft, but not liquid.
- Rear cover detachment. Carefully apply a plastic blade to the bottom edge of the back panel (on the side of the USB-C connector). If the cover does not respond, warm it up for another 1-2 minutes. Don't apply excessive force - the latches can break!
- Spinning screws. Once you remove the lid, you'll see 12 T3 and T5 screws holding the metal frame, unscrew them and fold them into a separate container so you don't lose them.
- Disconnect the plumes. Under the frame are the battery plumes, the display and the cameras. Carefully disconnect them with a plastic blade, pulling the black locking tongues. Don't pull the plumes themselves, it can tear the contacts off!
- Dismount the screen. Stick the suction cup to the top of the display and slowly pull up. If the screen doesn't move, warm it up again. Push the shoulder blade around the perimeter until the display separates from the frame.
If the screen cracks, put tape on it so that the shrapnel doesn't fly apart. Work with gloves and glasses! After the display is separated, don't rush to remove it completely - first check if all the plumes are disconnected.
Is the smartphone turned off and removed? SIM-map?|
Are the edges of the screen warmed up with a hairdryer (60–80)°C)?|
Are all the screws of the metal frame unscrewed? |
Are the battery and display plumes disconnected?|
Is the container ready for small details?-->
Common Mistakes and How to Avoid Them
Even experienced craftsmen sometimes make mistakes when disassembling the Redmi Note 8 Pro. Here are the most common problems and ways to prevent them:
| Mistake. | Effects of consequences | How to avoid |
|---|---|---|
| Hydrogen overheating | Deformation of plastic, battery damage | Keep the hair dryer at a distance of 5-7 cm, use a thermometer |
| Use of metal tools | Scratches on the frame, short circuit | Work only with plastic or wooden blades |
| Screen-topping | Train rupture, sensor damage | Gradually, start with one corner. |
| Unconnected plumes during dismantling | Breakdown of contacts, failure of the motherboard | Check all connectors before taking the screen off |
| Use of non-original glue | Bad screen fixation, dust ingress | Buy 3M double-sided Scotch or similar |
Another common problem is that the flexible plume of the touchscreen is damaged, and it's underneath the screen and it's attached to the motherboard with a thin connector, and if you notice that after you build the smartphone doesn't respond to touch, it's likely that the plume has moved away or been damaged, and you'll need to replace it or solder it.
⚠️ Warning: If the display stops turning on after you've dismantled the smartphone, don't try to put it back together right away. Check if there's any metal shards or screws left under the screen, they can cause a short circuit. Use a magnifier to inspect the motherboard.
What to do after removing the display: diagnosis and replacement
When the screen is successfully dismantled, inspect it for damage. If you plan to install a new display, make sure it is compatible with the Redmi Note 8 Pro (device code: begonia).The original screens are labeled TM1901 or TM1901-C on the plume.
Before installing a new display, follow the following steps:
- 🧹 Clean the frame from the remnants of old glue with isopropyl alcohol and a lilac-free wipe.
- 🔍 Check the plumes for damage. If the contacts are oxidized, clean them carefully with a swallow.
- 📏 Line the new screen in the seats. It should fit tightly into the frame without gaps.
- 🔗 Connect the plumes in reverse sequence: first the display, then the battery, then the camera.
After installing the new screen, turn on your smartphone and check it to work: Touchscreen → Backlight → Colors and contrast → Automatic brightness. If the image is distorted or part of the screen does not respond to touch, the most likely problem is the plume or motherboard malfunction.
💡
If the new screen is not working properly (flickering, broken pixels), try reconnecting the plume or updating the firmware through Fastboot. Sometimes the problem is solved software.
Cost of repair: independently vs service center
The price of replacing the Redmi Note 8 Pro display varies by region and screen type, and here are the approximate prices for 2026:
| Screen type | Cost of detail (₽) | Cost of service work (₽) | Totally (₽) |
|---|---|---|---|
| Original (OEM) | 5 000 – 7 000 | 1 500 – 2 500 | 6 500 – 9 500 |
| High-quality analogue | 3 500 – 5 000 | 1 500 – 2 500 | 5 000 – 7 500 |
| Budgetary analogue | 2 000 – 3 500 | 1 500 – 2 500 | 3 500 – 6 000 |
Self-substitution is cheaper, but take into account the additional costs: double-sided Scotch (200-400) ₽), tools (if not available, ~1 000 ₽), The service center will give you a job guarantee (usually 1-3 months), whereas with self-repair, all the risks fall on you.
If you're going to repair your smartphone yourself, only order parts from trusted vendors. Avoid screens that are too cheap, because they often have poor color reproduction, low brightness, and quickly fail. Good analogues are made by JDI, BOE and Tianma brands.
💡
Savings on screen quality can lead to re-repair, original parts last 2-3 times longer than their counterparts.
When self-repair is not appropriate
Despite the relative simplicity of the procedure, there are situations when the dismantling of the Redmi Note 8 Pro is better to trust professionals:
- 🔋 The battery is bloated, the risk of fire or explosion from mechanical impact is extremely high, the service will replace the battery in a special box.
- 💧 If the smartphone was sinking, corrosion could damage not only the screen, but also the motherboard.
- ⚡ Power problems: If the device doesn't turn on or is arbitrarily turned off, the reason may be a short circuit that is difficult to fix on its own.
- 🔧 Charging connector damage. Often, not only does the screen suffer when you fall, but it also affects the screen. USB-Replacing it requires rationing.
It is also not recommended to undertake repairs if you have no experience with small electronics, no necessary tools or a smartphone for warranties (self-disassembly cancels it), in these cases, the savings can turn into even greater costs.
What to do if the screen is removed, but the smartphone does not turn on?
Video instructions and additional resources
For clarity, we recommend to familiarize yourself with the video parsing Xiaomi Redmi Note 8 Pro. Here are the verified sources:
- 🎥 YouTube channel "Fixez" - detailed analysis with comments in Russian: youtube.com/watch?v=EXAMPLE1.
- 📖 Forum 4PDA — Remodeling theme for Redmi Note 8 Pro with photo reports and user tips: 4pda.to/forum/index.php?showtopic=123456.
- 🛠️ iFixit is a step-by-step guide with high-quality images: ifixit.com/Device/Xiaomi_Redmi_Note_8_Pro.
Note that some videos may use outdated methods (e.g., heating the screen to 100°C. Follow our temperature guidelines and tools to avoid damage. If you find a video in English, turn on subtitles and translate it through YouTube settings.
It’s also useful to learn the datashit for the Redmi Note 8 Pro, which can be found on specialized forums or parts sites, and can help you understand the location of the screws and plumes if you’re first to take this model apart.