Disassembly Xiaomi Mi 9C: how to carefully remove the display without damage

Xiaomi Mi 9C — compact AMOLED-It's a display that, despite being built reliably, is not immune to falls and cracks on the screen, and if you're faced with broken glass, broken touch zones, or artifacts on the matrix, replacing the display is often the only solution. However, repairs in the service center can cost half the cost of the device - that is why many users decide to disassemble themselves.

In this article, you will find step-by-step instructions for removing the display from the Mi 9C, including a list of necessary tools, nuances of working with the adhesive layer and ways to avoid typical errors, we will also analyze when to change only the glass and when to completely replace the module, and provide a list of proven spare parts suppliers with compatibility in mind.

We warn you beforehand: the procedure requires care and patience. One wrong move can damage the plumes, disconnect contacts, or even break the motherboard. If you've never disassembled a smartphone, practice on an old device or consult a professional.

Preparation for disassembly: tools and materials

Before you start dismantling the display, make sure you have everything you need, and using the wrong tools is the main cause of damage to the body or internal components, and here is the minimum set you'll need:

• 🔧 Plastic mediators or shoulder blades (thickness 0.1–0.2 mm) – for separation of glued parts.
• 🔥 Dryer or thermo-air station (power 300-500 W) - for softening the glue.
• 🧲 Suction cup for displays (diameter 4-6 cm) - helps to evenly tamper with the screen.
• ⚙️ Screwdriver. T3 and T5 — mid-frame.
• 🧴 Isopropyl alcohol (90%+) — cleaning up glue residues and contacts.
• 📦 New glue layer (LOCA or OCA) — If you plan to reassemble the device.

Additionally, we recommend buying an antistatic bracelet (or at least work on a grounded surface) and a backlit magnifier – many of the plumes and contacts on the Mi 9C are miniature, and they are easy to miss.

⚠️ Warning: Do not use metal blades or knives to smack the display! Even a small scratch on an aluminum frame can become a hotbed of corrosion, and damage to the touchscreen plume will lead to a broken sensor.

If you replace only glass (without a matrix), you will need a special glue. B-7000 or UV-glue to bond new glass with the original display, a standard double-sided tape or a complete module replacement is sufficient. LOCA-glue.

Step 1: Turn off and heat the device

The first step is to turn off the power completely. Even if the screen does not respond to touch, make sure that the smartphone is turned off: press the power button for 10-15 seconds. If the device does not respond, try charging it to at least 10% - this will help to avoid a sudden disconnection during disassembly (some models block access to the plumes when the battery is discharged).

Then you need to heat up the adhesive layer to separate the display from the body.

1. Set the dryer at a temperature of 60-70 ° C (not higher, so as not to damage plastic parts!).
2. Evenly warm up the edges of the display for 2-3 minutes, holding the hair dryer at a distance of 5-7 cm.
3. Pay special attention to the corners - there the glue usually holds stronger.

Don't overheat one place for too long, it can warp the frame or damage the matrix. If you don't have a hair dryer, you can use a warm heating pad (wrapped in a towel) or place your smartphone under an incandescent lamp for 10 to 15 minutes.

💡

If the glue is not amenable even after heating, try to gently swipe the edge of the display with a thin guitar string (0.1 mm), which helps cut the adhesive layer without risking damage to the plumes.

Step 2: Dismantling the back cover and battery

On the Xiaomi Mi 9C, the display is not only glue-mounted, but also screws under the middle bezel, and to get to them, you have to remove the back cover.

1. Warm up the back panel with a hairdryer (similar to the display).
2. Insert a plastic mediator into the gap between the lid and the frame (start at the bottom edge where the USB-C connector is located).
3. Carefully drive the mediator around the perimeter, separating the latches. Be careful - they are fragile!

When you remove the lid, you'll see a battery that's also blocking access to the display, and you'll need to turn it off:

• 🔋 Disconnect the battery plume from the motherboard (use a plastic shoulder blade).
• 🔧 Unscrew the screws fixing the metal plate over the battery.
• 🧴 Tap the battery with a plastic blade (do not use metal!) and remove it carefully.

⚠️ Warning: If the battery is swelling, don't try to puncture or bend it! This can cause fire.

Once the battery is removed, unscrew all the screws holding the middle frame. Their location may vary depending on the Mi 9C modification, so we recommend taking a picture of the disassembly process or drawing a diagram.

Step 3: Disconnect the display plumes

Now that the frame is removed, you'll have access to the display and touchscreen plumes. There are two on the Mi 9C:

• The main plume of the matrix (wide, goes to the top of the board).
• The plume of the sensor layer (thinner, located next to it).

Both are attached to the motherboard using latches-connectors.

To disconnect them:

1. Carefully tuck the latch with a plastic spatula (it is usually white or black).
2. Pull the plume up parallel to the board (not at an angle!).
3. Check if there is any bilateral scotch left under the plumes - it must be removed with alcohol.

If the plume doesn't move, don't force it! It may have an extra layer of glue, in which case, warm up the area with a hairdryer 50°C and try again.

Step 4: Removing the display and cleaning the case

When the plumes are off, you can start taking the display off directly.

1. Install the suction cup on the bottom of the screen (where the USB-C connector is located).
2. Carefully pull up, while putting the edge on the plastic mediator.
3. As soon as a slit appears, insert a mediator into it and lead along the edge, separating the glue.

Take your time! The glue on the Mi 9C is often uneven, and in some places the screen may stick more, and if you feel resistance, warm up the problem area with a hairdryer again.

After removing the display, clean the body of glue residues:

• 🧴 Use isopropyl alcohol and a lilaless napkin.
• 🔍 Pay attention to the depressions under the plumes - there often accumulates dust.
• 🚫 Do not use acetone or solvents – they can damage plastic!

Make sure all plumes are turned off |Clean contact areas with alcohol |Check new display for defects |Approach new adhesive layer (LOCA/OCA) |Connect battery before testing-->

Common Mistakes and How to Avoid Them

Even experienced craftsmen sometimes make mistakes when disassembling the Xiaomi Mi 9C. Here are the most common of them and ways to prevent them:

• 🔧 Shooting screws - use high-quality screwdrivers with a magnetic tip and do not apply excessive force. 9C squirt".
• 🔥 Overheating board - don't point the hair dryer directly at the motherboard. Maximum temperature for heating glue is 70.°C.
• 📱 Damage to plumes - never pull them at an angle. The plumes must extend parallel to the board.
• 🔋 Short circuit - before any manipulation of the board, turn off the battery. Even a discharged battery can cause a voltage surge.

On the Mi 9C, the plume of the touchscreen is particularly fragile - it is only 0.05 mm thick. If you feel that it is "jammed" in the connector, do not try to pull out by force.

Another common problem is that the new display is not glued uniformly, and if you use too much LOCA glue, it can leak out over the edges and lock the speaker or microphone, and the optimal layer is 0.1 to 0.15 mm.

Where to buy spare parts for Xiaomi Mi 9C

Part quality is directly related to the result of repairs. Cheap displays with AliExpress often have poor color reproduction, broken touch screen areas or fast-burning pixels. We recommend buying components from trusted suppliers:

When buying, check if the adhesive layer and protective film are included. Some vendors sell displays without them, which will make installation difficult. Also pay attention to the display version - for the Mi 9C, there are modules with different plume connectors (for example, for the European and Chinese versions).

💡

Before buying a spare part, be sure to check its article! the original display for the Mi 9C is labeled DM-063-01-A (may vary depending on the region).

Assembly and testing after replacement

The new display is installed in reverse order, but there are a few key points:

1. Applying glue: If you use LOCA, Spread it evenly across the edges of the display, avoiding the center (there is a matrix). OCA-film is enough to remove the protective layer and carefully apply the display.
2. Connect plumes: Start with the touchscreen, then plug in the matrix plume. Make sure the latches are fixed before the click.
3. Testing: Connect the battery and turn the smartphone on before final assembly: 📱 The performance of the touch screen (take the test in Settings) → The phone. → Diagnostics). 🎨 Color rendering (whether yellow or broken pixels). 🔊 The speaker and microphone (sometimes the glue blocks the holes).

If everything works correctly, put the body in reverse order. Rotate the screws cross-twisted to avoid skewed frames. After assembly, check the tightness - if the screen "plays" when pressed, then there is not enough glue.

⚠️ Warning: If the smartphone starts to run out quickly after replacing the display, check if the battery plume is closed. Sometimes, with a careless assembly, the contacts touch a metal frame, which leads to increased power consumption.

FAQ: Frequent questions about replacing the display Xiaomi Mi 9C