Disassembly Xiaomi Redmi Note 9S: detailed instructions for repair

Modern Redmi smartphones are high performance and affordable price, but their design often requires a special approach to repair. Model Redmi Note 9S (also known as Redmi Note 9 Pro in some regions) has a glass back and a complex system of mounts, which makes self-disassembly risky task without proper preparation.

The main difficulty of the process is that the body of the smartphone is assembled without visible screws, and all the elements are held by a powerful adhesive compound. To successfully perform the procedure, you will need not only a set of special tools, but also patience, as well as accuracy of movements. In this article, we will take a detailed look at each stage of dismantling, focusing on the safe detachment of the plumes and the correct procedure to avoid fatal errors.

Before you start to physically affect the case, you need to prepare the workplace. The surface must be clean, well-lit and free of unnecessary objects that can scratch the glass or get lost. It is also extremely important to completely turn off the device before work begins, since an accidental short circuit can disable the motherboard or power controller.

Tools and workplace preparation required

High-quality disassembly of Xiaomi Redmi Note 9S is impossible without specialized tools that will allow you to work with high accuracy. The use of improvised tools such as knives or needles is strictly not recommended, as they can damage the internal plumes or shatter the glass of the case. Professional craftsmen use kits designed specifically for mobile electronics.

First of all, you'll need a heating element to soften the glue, which can be a professional thermopanel that keeps the temperature around 80-90 degrees, or a regular household hair dryer. It's important not to overheat the device so as not to damage the display or battery, so temperature control is a critical parameter, and you'll also need suction cups of different diameters to carefully pull the back cover.

Small screws require a set of precision screwdrivers that includes PH00 and PH000 cross bits. The screws in Xiaomi smartphones can be of different lengths, so it is recommended to use a magnetic mat or a special map with a markup where you will lay the fastener in order of its extraction. This will save you time when you build and prevent a situation where a long screw will be screwed into a short hole, which can break through the motherboard.

In addition, prepare the following tools:

• 🛠️ Plastic mediators (scapula) for clipping and separation of body layers without damage.
• 🧤 Antistatic tweezers to capture small parts and plumes to avoid damage to fingers and static discharge.
• 🧴 Isopropyl alcohol or special solvent of glue (B-7000) cleansing.
• 🔦 Powerful magnifier or microscope for visual monitoring of connectors and small elements.

⚠️ Note: Before starting the work, be sure to remove SIM-Attempting to heat or disassemble a phone with a set-up SIM-The card can lead to deformation of the tray and damage to the contact group inside the device.

Removal of the back cover and primary access

The first stage of dismantling Redmi Note 9S This is the removal of the back panel, which is made of glass and glued around the perimeter. This process requires even heating, because the uneven distribution of temperature can lead to cracks in the glass. 3-5 minutes, constantly moving the heat source so as not to create a point of overheating in the center.

Once warmed up enough, you need to create an initial gap. Use a suction cup by attaching it to the bottom of the back cover, and gently pull it up while inserting a thin metal or plastic probe into the resulting slit. You need to act extremely carefully to avoid damaging the plume (fingerprint scanner), which can be located close to the edge, although in this model it is often integrated into the side button.

Once the probe has entered, replace it with a plastic shoulder blade and start driving it along the perimeter, cutting the adhesive layer. The movements should be sliding, not stabbing, so as not to damage the internal components. Pay special attention to the corners where the glue is usually the most, and the areas around the main camera module where the glass may be thicker.

Important points when removing the cover:

• 🔥 Do not heat the device above 90 degrees to avoid battery bloating or damage OLED-Matrix (if installed in your version).
• 👐 Hold your phone securely, but without excessive pressure so that the glass doesn’t burst in your hands.
• 🧩 Move slowly, feeling the resistance of the glue, and add heating if necessary.

💡

If the back cover cracks when you remove it, don't try to glue it right away. First, completely clean the frame of the shards and old glue, otherwise the new panel will lie unevenly and will peel off.

Dismantling the protective panel and disconnecting the plumes

Once you successfully remove the back cover, you will see an interior space that is enclosed by a plastic protective panel (medium frame), which covers the battery, the bottom board and part of the motherboard, and also presses the display plumes, which are secured by many screws of different sizes, which must be twisted in strict sequence.

The center of the panel is often located NFC-The module and antenna contacts, which require careful handling, and after you twist all the visible screws around the perimeter and in the center, gently lift the panel. It can hold on to the adhesive strips, so use the blade to separate it. Under the panel you will see the main battery and connectors going to the motherboard.

The next critical step is to turn off the power, find the battery connector and gently disconnect it using a plastic blade or nail, and then you can turn off the plumes of the display, touchscreen and other modules. The order of shutting down the plumes is important: first, always take off the power, then the signal plumes.

Table of the main connectors under the protective panel:

⚠️ Warning: Metal locks on the plume connectors (if any) must be bent before the plume is removed.

Battery extraction and glue handling

In the Redmi Note 9S, the battery takes up a significant portion of the internal volume and is often attached to double-sided tape or glue. Simple battery pulling is prohibited, as it can damage, ignite or bloat. Chemical solvents or special hoods are required to safely extract.

The best method is to inject isopropyl alcohol under the battery through special holes (if designed) or around the perimeter. After the liquid is injected, you need to wait 5-10 minutes for the solvent to penetrate deep and soften the adhesive layer. Then you can use plastic cards or special tapes to gradually separate the battery from the housing.

When working with lithium polymer batteries, punctures and deformations should be avoided. If the battery is damaged and starts to smoke or hiss, immediately stop work, isolate the device and take it out into the open. A damaged battery is a serious danger.

Basic safety rules when working with ACB:

• 🔋 Never pierce the battery with sharp objects.
• 🌡️ Avoid overheating the battery with a hairdryer directly, only heat the glue area around it.
• 🚫 Do not use metal tools to tamper with the battery.

💡

Safely extracting the battery is the riskiest step, requiring patience and the use of solvents rather than physical force.

Replacement of the display and camera module

Replacing the display with the Xiaomi Redmi Note 9S often requires removing the front bezels or working with the separator if you change only the glass. However, at home, you usually change the entire module assembly (frame + screen + touchscreen), to remove all components, transfer them from the old broken module to the new one.

The main camera module in this model is large and dust sensitive, and when you remove it, you need to unscrew the locking screws around the lens and carefully disconnect the plume. Notice the condition of the lenses: the presence of dust on the inside of the lens after assembly will lead to black dots in the photos.

When installing a new display, be sure to check its performance before the final gluing of the case. Connect the plumes, turn on the phone and check the sensor, color reproduction and the presence of broken pixels. It is also worth checking the vibration and speakers, as access to them after gluing will be difficult.

Nuances of work with optics:

• 📸 Do not touch the surface of the camera lenses and sensors.
• 🌬️ Blow the insides of the case with compressed air before installing a new module.
• 🔍 Make sure that the camera stabilizer (OIS) Not jammed with transport fixtures (if they are on a new part).

Assembly of the device and verification of functionality

The final stage, the Redmi Note 9S assembly, requires care and all screws are returned to their places. Make sure all plumes are snapped to a characteristic click and the connectors sit tight. Before applying the new adhesive, be sure to remove the remnants of the old adhesive from the frame of the case, degreasing the surface with alcohol.

For sealing, use a special B-7000 glue or ready-made adhesive frames (gasers) that provide a factory level of moisture protection (although it is difficult to completely restore IP53 at home). Apply the adhesive with a thin layer, press the back cover and lock the device with rubber harnesses for 30-60 minutes until completely dry.

Once assembled, run a full test of functionality: check charging, Wi-Fi, Bluetooth, GPS, all cameras, microphones and speakers. Make sure the phone doesn't warm up to a simple one and keeps the charge. If all systems are working properly, you can consider the repair successfully completed.

Checklist before inclusion:

• ✅ All screws are twisted, there are no unnecessary details.
• ✅ The plumes are connected securely and to the point.
• ✅ The battery is connected and shows voltage.
• ✅ The lid is flat, the lid is flat without gaps.

⚠️ Warning: If the phone doesn't turn on after assembly, don't panic. Check the connection of the display plume and battery. Often the problem lies in an incompletely inserted connector.