How to disassemble Xiaomi Mi Max 2: Safe instruction with photos and nuances

Xiaomi Mi Max 2

5,300 mAh

climactic

Many Mi Max 2 owners face typical problems: the phone doesn't turn on after a fall, doesn't charge, or the screen starts to "glut." 80 percent of the time, it's mechanical damage to the internal components, and you can't do it without disassembling. But before you take the screwdriver, you need to evaluate your strength: a mistake in dismantling can lead to irreversible damage to the display plumes or to the detachment of the battery contact areas. If you're not sure, you should contact the service center. For those who are willing to take the risk, here is a detailed instruction with photos and tips from the masters.

Preparation for disassembly: tools and security measures

Before you start, you can pack everything you need, and without the right tools, you're at risk of damaging the body or the internal components, and here's the minimum kit you'll need:

• 🔧 Plastic mediators (2-3 Pc.) - for careful slinging of the lid and plumes.
• 🔩 The screwdriver. PH00 — This is the size of the Mi Max 2 screws.
• 🧲 Magnetic mat or container - so as not to lose small screws (there are about 15 pieces!).
• 🔥 Dryer or thermo-air station - to soften the glue under the battery.
• 📦 Screen suction cup – will help to gently lift the display (if you need to replace it).
• 🧴 Isopropyl alcohol (90%+) — Cleaning contacts and removing glue residues.

Also, prepare your workspace: the desk should be clean, well-lit and free of static electricity (ideally an antistatic mat), turn off your smartphone before disassembling, and if it doesn't respond to the power button, wait for the battery to run out completely (it will take a few days).

⚠️ Warning: If you disassemble a phone with a bloated battery (the cover is raised, the screen is “bulging”), in no case pierce it and do not heat it above 60°C. The risk of fire or explosion in this case is extremely high.

Before starting work, we recommend taking photos of all stages of disassembly, which will help to properly assemble the device back, and it is also useful to download the official firmware for the Mi Max 2 in case you need to reflash the device after repair.

Removing the back cover: secrets and pitfalls

The back cover of the Xiaomi Mi Max 2 is mounted on latches and glue, so removing it without damage is a whole science. To begin with, the cover is not glued to the dead, but if you sloppy dismantle, you can break the plastic locks or tear the fingerprint scanner plume (if you have one in your modification).

Algorithm of action:

1. Heat the edges of the cover with a hair dryer (temperature) ~50°C) during 2-3 It'll soften the glue.
2. Insert a plastic mediator into the gap between the lid and the frame (start at the lower right corner where the antenna is located).
3. Carefully drive the mediator along the perimeter, alternately snapping the locks. Don't force - if the lid fails, heat up more.
4. When all the latches are snapped, lift the lid, but don’t remove it completely – it is connected to the fingerprint scanner plume (if any).

At this point, many people make the mistake of trying to rip the lid off with a jerk, breaking the locks or tearing the plume, and if you have a model without a fingerprint scanner (like the global version), you can remove the lid immediately after the clips are snapped.

Battery shutdown: why it's critical

Once the lid is removed, the first thing you need to do is turn off the battery. In the Mi Max 2, it's located at the top of the device and glued to the body. It's dangerous to work with a connected battery: short circuits can disable the motherboard or even cause a fire.

Instructions for unsetting:

1. Find the battery connector on the motherboard (usually black with an orange or red marker).
2. Carefully put the connector on a plastic mediator and unplug it. Don't pull the wires!
3. If the connector is "stiffened", drop a little isopropyl alcohol on the contacts and wait 10 seconds.

After the battery is turned off, check the voltage on the motherboard with a multimeter (if you have one at hand).Ideally, it should be 0 V on all power contacts. If there is a voltage, there is a connection somewhere left (you may have missed the additional connector).

⚠️ Note: In some Mi Max 2 versions (e.g., the Chinese versions), the battery can be connected via a dual connector, one for power, one for the thermistor!

If you are planning a battery replacement, remember: the original batteries for the Mi Max 2 have a capacity of 5300 mAh and are labeled MDY11EG. Counterfeiting often gives off low capacity (4000-4500 mAh) and no protective controller. Check the battery before buying!

💡

If the battery is swelling, but the phone is still working, urgently make a data backup via Mi PC Suite - after disassembly, it may be impossible to turn on the device.

Dismantling the motherboard: a step-by-step guide

The Xiaomi Mi Max 2 motherboard is mounted on 12 different size screws (PH00 and PH0), so it is important to remember which screw is twisted from where. For convenience, you can spread them on a magnetic mat in order of extraction or photograph the location.

Procedure:

1. Twisted all the screws around the perimeter of the board (start at the top where the battery connector is located).
2. Carefully raise the charge with a plastic mediator, starting from the charging connector side.
3. Disconnect all plumes: 📱 Display plume (the widest, at the bottom of the board). 🔊 Dynamics and microphone plume (thin, right). 📡 antenna plume (may be glued, disconnect gently!). 🔋 The charger's sleeve (if not on a separate board).

Completely remove the board and put it on an antistatic surface.

At this point, many people are faced with a problem: the display plume is glued to the frame with double-sided tape. Don't try to tear it off by force, you better gently prick it with a mediator and drip alcohol to dissolve the glue. Also be careful with flexible antenna tracks, they easily break when handled carelessly.

Replacement of the display: when it is necessary and how to do it correctly

The Mi Max 2 screen is one of the most vulnerable places. Typical problems: cracks after a fall, broken pixels, a broken touchscreen or backlight. If the display is damaged, but the image is there, it is likely enough to replace the glass with an oleophobic coating. If the screen does not turn on or displays artifacts, you will need to replace the full module (display + touchscreen + frame).

To replace the display will need:

• 🔧 New screen module (check compatibility with your Mi Max 2 version, global or Chinese).
• 🧴 Double-sided tape or glue B-7000 fixative.
• 🔥 Hair dryer to soften old glue.
• 🧲 Suction cup and plastic mediators.

Replacement process:

1. Heat the screen with a hair dryer (a temperature of ~60°C) for 3-5 minutes to soften the glue.
2. With a suction cup, lift the display from one edge and gently tuck the mediator.
3. Disconnect the display plume from the motherboard (it is located at the bottom).
4. Remove the remains of old glue with alcohol frame.
5. Apply a new glue to the frame and install the new display, pressing it evenly.
6. Connect the plume back and check the operability before final assembly.

⚠️ Note: When replacing the display with the Mi Max 2, there is often a problem with a broken touchscreen after assembly. The reason is the wrong connection of the plume or damage. Before fixing the display with glue, be sure to check the sensor for the reaction!

The cost of a new display module for the Mi Max 2 varies from 3,000 to 6,000 rubles depending on quality. Original parts are difficult to find, but good copies (for example, from the manufacturer OEM-Level) last almost as long.

💡

If color distortions (e.g. yellow) appear after the display is replaced, the problem is the poor quality plume. Try reconnecting it or replacing it with a new one.

Phone Assembly: How to Avoid Mistakes

Getting the Xiaomi Mi Max 2 back together is often harder than disassembling. The main rule is: check every step.

1. Make sure all plumes are tightly connected (clicking should be heard).
2. Twirl the screws in reverse order, without putting unnecessary effort (especially carefully with screws near the charging connector).
3. Stick the battery to double-sided tape (do not use superglue!).
4. Install the back cover starting at the top and snap all the locks.

After assembly, perform the test:

• 🔋 Check charging (plug the cable and make sure the current is going).
• 📶 Make sure you catch the network (if the antennas are connected correctly).
• 🔊 Test the speaker and microphone (record a voice note).
• 📱 Check the touchscreen for responsiveness (especially around the edges).

If the phone does not turn on after assembly:

1. Check the battery connection and the power connector on the board.
2. Make sure that no plume is covered.
3. Connect to charging for 10-15 minutes – sometimes it takes time to initialize.

If nothing works, it may have damaged the motherboard during the disassembly, in which case you will need to be diagnosed using a USB-OTG tester or multimeter.

Frequent problems after disassembly and how to solve them

Even if you do everything according to the instructions, after the dismantling, there may be problems.

If after repair the phone turns on but is not determined by the computer, the problem may be damage. USB-In this case, only the replacement of the charging module (cost) will help. ~1 500 rubles).

Another common complaint is that you overheat after assembly, and it can be because of:

• 🔥 Incorrectly installed heat-dissipating tape on the processor.
• 🔋 Bloated battery (even if not visually noticeable).
• 📱 Motherboard pollution (dust, flux residues).

In any case, if the problem is not solved by a simple bulkhead, it is better to consult a specialist, for example, a diagnosis in a service center will cost 500-1000 rubles, which is cheaper than buying a new board due to a repair error.

💡

If after disassembly the phone began to reboot arbitrarily, check the contacts of the power button - it could shift or oxidize.

FAQ: Answers to Frequent Questions