How to disassemble Xiaomi Redmi 8T: a detailed guide to replacing components

Modern smartphones, including popular Xiaomi models, are designed to minimize their dimensions, which often makes them difficult and risky to disassemble. The Redmi 8T is no exception: its body is glued around the perimeter, and the internal components are compact, requiring a high-precision wizard and a specialized tool. Self-disassembly is necessary when you need to replace a broken display glass, install a new battery or fix the charging connector, and understanding the structure of the device is critical to success.

Before you start dismantling, you need to realize that any interference with the design of the gadget deprives the owner of the warranty if it has not expired. However, if the phone has already left the warranty period or the damage is mechanical, neat disassembly becomes the only way to bring the device back to life without going to the service center. In this guide, we will look at each step of the work, paying special attention to hidden screws and fragile plumes.

Preparation of the workplace and the necessary tool

Quality preparation is the foundation of successful repairs that directly affect the safety of small parts and the speed of work. You will need not just a flat surface, but also good lighting, as well as a magnetic mat or container with screw sorting cells, since the Redmi 8T uses fasteners of different lengths and types. Ignoring this stage often leads to the loss of microscopic screws or confusion, which makes the assembly a complex puzzle.

The basic toolkit should include a glass lifting suction cup, a set of plastic mediators (scapula) and a set of precision screwdrivers, necessarily including cross P2 and P000. To work with the adhesive base, you will need a hair dryer or heating platform that can maintain a temperature of about 80-90 degrees without overheating the display matrix. It is also recommended to prepare tweezers with curved ends and isopropyl alcohol to dissolve the glue.

⚠️ Warning: Before any work begins, be sure to completely turn off the device. Attempting to disconnect the plumes under voltage can lead to a short circuit and failure of the power controller on the motherboard.

Special attention should be paid to the cleanliness of the workspace, as dust and static electricity are the enemies of electronics. It is advisable to work on an antistatic mat and periodically touch the grounded metal object to remove static charge from the body. If you do not have an antistatic bracelet, just touch the metal parts of the case or grounded objects more often.

Removal of the back cover and primary access

The process of opening the case Xiaomi Redmi 8T begins with heating the perimeter of the rear panel, which is attached to double-sided tape and glue. Carefully warm the edges of the device with a hairdryer for 2-3 minutes, constantly moving the flow of hot air to avoid local overheating of glass or plastic. Periodically check the degree of softening of the glue, trying to slightly twist the suction cup or insert a thin mediator into the joint.

After enough warming up, insert the plastic blade into the bottom end, where the charging connector normally is, and make a careful movement to dissect the glue. Don't try to dive the tool deep into the inside right away; your job is to create a small slit that will then enter the mediator thicker. Lead the tool along the side faces, cutting the adhesive layer, but be extremely careful at the top where the plumes are located.

• 🔥 Heat the body evenly, without holding the hair dryer at one point longer. 5-10 seconds.
• 🛠️ Use only plastic tools for snapping, metal can damage the frame.
• ⚠️ Avoid pressure on the center of the back cover so as not to push the display glass on the back side.

When the perimeter is passed, don't be in a hurry to remove the lid completely, as it can be glued to a fingerprint scanner or a plume that goes to the board. In the Redmi 8T model, the scanner is often integrated into the rear panel, and its plume requires careful deactivation. First, examine the inside of the lid and find the connection of the plume to the motherboard or intermediate connector.

💡

If the glue is not heated, drop a little isopropyl alcohol into the gap between the lid and the frame - this will help dissolve the adhesive and facilitate the removal process without damage.

Dismantling of the protective panel and battery

Once the back cover is successfully removed, you will see an internal layout that includes a battery and plastic protection panel, which covers the motherboard and is mounted with a lot of perimeter screws that need to be twisted out before you take it off. The Redmi 8T may also have sticker or plug screws, so check the surface carefully for hidden fixtures.

The next critical step is to disconnect the battery from the motherboard. Even if the phone is turned off, there's still a voltage on the board, and sloppy movement of the metal tool can cause a spark. Use a plastic blade to turn off the battery connector, lifting it up slightly, and only then continue to work on removing the protective screens and other components.

If the battery itself is to be replaced during the repair process, it is delicate to remove, as it is planted on a powerful glue. Do not use metal objects to tamper with the battery, as the lithium-polymer cell shell puncture causes instantaneous ignition. Carefully tamper with the edges of the battery with a plastic card or a special spatula, preheating the area under the battery through the case or using special pull-out tapes.

Replacement of the display and work with plumes

Replacement of the display with Redmi 8T — This is the most difficult step, because the matrix is glued to the frame of the case and requires reheating to separate, and after removing all screws and turning off all plumes that pass through the frame or go to the buttons, you need to warm up the front of the device. Excessive heating can damage OLED-matrix (if installed there) or cause deformation of the plastic frame.

Use a suction cup and mediators to carefully separate the display module from the body, moving around the perimeter and gradually cutting the adhesive layer. The main danger here lies in the plumes that can pass under the frame or be glued to it; they are easy to break with careless jerk. Always check if all connections are broken before applying force to remove the screen.

⚠️ Attention: The display and touchscreen plumes are very thin and sensitive to clamps. Never bend them at a sharp angle or pull on the conductor itself, hold on only to the thickened connector.

When installing a new display, make sure that the frame is free of shards of old glass or clumps of old glue that can create unevenness and lead to a crack of the new module when assembled. Degrease the frame surface with alcohol, apply a new adhesive layer (B-7000 or similar), and gently install the module by pressing it around the edges. Connect the plumes until final fixation to check the performance of the image and touch.

Assembly of the device and verification of functionality

The smartphone is assembled in a reverse disassembly order, but requires attention to details that may have been missed during the dismantling process.Make sure all screws are returned to their places, especially those that fasten the motherboard, as their absence can lead to poor contact of the connectors or a violation of the heat sink.Swipe the screws evenly, without excessive effort, so as not to break the thread in the plastic bushings.

Before the final sticker on the back cover, it is recommended to run a test run of the device. Connect the battery and the display plume, press the on button and check the basic functions: sensor operation, sound, vibration, cameras and charging. If everything works correctly, you can apply glue to the frame and fix the back panel, pressing it tightly around the perimeter.

• 🔍 Check if there are any extra screws or parts left after assembly.
• 📱 Make sure the display has no dead zones and multi-touch is running.
• 🔋 Control the temperature of the device at the first charge after repair.

The final step is to clean the case of traces of glue and fingerprints that may have remained in the process of work.Let the adhesive layer of the back cover dry for several hours, preferably putting the phone under a small press (for example, under a stack of books through a soft fabric) to ensure uniform fit and reliable tightness of the case.

💡

The build quality directly affects the moisture protection and durability of the repair, so do not save time cleaning the frames and checking all the connections before the final gluing.

Frequent errors and expert recommendations

One of the most common mistakes in disassembling the Xiaomi Redmi 8T is neglecting heating, which leads to breakage of plastic latches or cracks in the glass. Many beginners try to force the lid out, not realizing that modern adhesive at room temperature holds very tight. patience and correct temperature regime are key factors of success.

Another mistake is to use inappropriate screwdrivers that lick the screw caps. Budget models often use soft metal for screws, and a cheap tool can irrevocably spoil the fastener. Use quality bits with good coating and exactly the right size to avoid problems when reassembling.

⚠️ Warning: Do not use superglue (cyanacrylate) to fix components inside the enclosure. Its vapors can settle on camera lenses and sensors, causing them to become cloudy and fail.

Also worth mentioning is the problem of static electricity, which is often forgotten in dry rooms: a discharge of statics can kill sensitive electronics instantly and unobtrusively to the eye. Work on an antistatic mat, humidify indoor air or use an antistatic bracelet connected to the ground, especially in winter.