How to disassemble Xiaomi Mi 2 Lite: detailed instructions with photos and tips

The Xiaomi Mi 2 Lite (codenamed armani) is a popular 2013 model that is still used by many users, and may need to be disassembled to replace the battery, repair the display, clean up the dust or recover from a fall, but it requires care: wrong actions can damage the plumes, detach the sensor, or even break the motherboard.

In this article, you will find step-by-step instructions with photos of key stages, a list of necessary tools and unique tips to help avoid typical errors, we will also tell you which parts of the Mi 2 Lite often fail and how to diagnose them before disassembly.

⚠️ Warning: Disassembling your smartphone will void the warranty (if it is still valid) and can cause permanent damage. If you are not sure about your skills, contact the service center.

Preparation for disassembly: tools and security measures

Before you start, make sure you have everything you need. Xiaomi Mi 2 Lite is assembled on latches and screws, so you can not do without specialized tools.

• 🔧 Plastic blade (or mediator) - to disconnect the body without scratches.
• ⚙️ The screwdriver. PH00 — screws in Mi 2 Lite small, the usual screwdriver will not fit.
• 🧲 Magnetic mat or screw container – so as not to lose details.
• 🔥 Hair dryer or thermo-air station - if the battery glue is too strong.
• 🧴 Isopropyl alcohol (90%+) — Cleaning contacts and removing glue residues.
• 📸 Smartphone for photography – capture each step so as not to confuse details during assembly.

Also, prepare your workspace: it should be well lit, without carpeting (screws are easily lost), and with minimal static electricity. If you work on a wooden desk, put an antistatic mat or at least regular paper.

⚠️ Warning: Do not disassemble your smartphone at humidity above 60% - this can cause corrosion of contacts. If the Mi 2 Lite has recently been in a damp room, dry it in rice or silica gel for at least 12 hours.

Step 1: Removing the back cover

The Xiaomi Mi 2 Lite has two parts attached by latches around the perimeter to remove the back cover:

1. Turn off your smartphone and remove it. SIM-card and memory card (if installed).
2. Place the plastic blade in the gap between the back cover and the screen at the charging connector.
3. Carefully swipe along the body, disengaging the latches. Do not apply force - if the lid does not respond, warm it with a hairdryer (temperature not higher than 60 ° C).
4. After all the latches are snapped, remove the lid, starting at the bottom edge.

Under the lid, you'll see:

• 🔋 Battery (stick to the body).
• 📱 Motherboard with foil protection.
• 📷 Main camera module.
• 🎤 Microphone and speaker.

💡

If the back cover cracks when you remove it, do not try to glue it with superglue - this can damage the plastic.

Step 2: Shutting off the battery

Before any manipulation of the internal components, be sure to turn off the battery. In the Mi 2 Lite, it is connected via a connector on the motherboard:

1. Find the black battery plume (usually marked with a red or orange mug on the board).
2. Carefully slap the connector with a plastic spatula, pulling up. Don't use metal tools!
3. Make sure the contacts are not closed - touching a screwdriver can burn the board.

If the battery is swelling (as seen from the deformation of the case), do not try to pierce or bend it - this can lead to fire.

• 🚫 Don't turn on your smartphone.
• 🔧 Carefully remove the battery without damaging its shell.
• 🗑️ Dispose of it in a special reception point (do not throw it into ordinary garbage!).

Step 3: Removing the motherboard

The Mi 2 Lite motherboard is mounted on 10 screws (size 1.5 mm) and several latches to remove it:

1. Unscrew all the screws, starting at the corners of the board. Fold them in order of extraction (for example, the scheme "top-left → top-right → bottom-left → bottom-right").
2. Disconnect the plumes: 📞 Touchscreen plume (white latch). 📸 Main camera plume. 🔊 Dynamic/microphone plume.

70°C

On the back of the board you will see:

• 📶 Antenna modules (do not bend them!).
• 💾 EMMC memory chip (if you are planning a replacement, take a Samsung model) KLMBG4GE4A).
• 🔌 Connector for display.

⚠️ Warning: If you see corrosion (green or white) on the surface of the board after you remove it, it's a sign of moisture. In this case, you need an ultrasonic cleaning in the service center - self-washing with alcohol may not help.

Step 4: Disassembly of the display module

The Mi 2 Lite screen consists of three layers: a protective glass, a touchpad and an LCD matrix. If you need to replace only the glass, you can do without completely disassembling, but if you damage the matrix or touchscreen, you have to disassemble the entirety.

Procedure:

1. Warm up the edge of the screen with a hair dryer (temperature 50-60 ° C) for 2-3 minutes - this will soften the glue.
2. Place the suction cup on the bottom of the screen and pull it up. If the glass is cracked, paste it with tape so the shrapnel doesn't fly apart.
3. Carefully separate the screen with a plastic blade, moving from the corner to the center. Do not insert the blade deeper than 2 mm - there are plumes under the screen!
4. Disconnect the touchscreen and display plumes from the motherboard (they are fixed with latches).

If you replace only the protective glass, it can be separated from the sensor by using the UV-It's glue and ultraviolet light, but it's going to take a lot of time:

• 🔦 UV-lamp (power not less than 36 W).
• 🧴 Special glue (e.g., glue, B-7000 UV).
• 📏 Template for alignment (can be printed on the printer).

Hair-dryer screen

Secure the sucker.

Separate the glass with a spatula

Disconnect the plumes

Check the new screen for broken pixels-->

Step 5: Diagnostics and replacement of components

After disassembly, it is recommended to diagnose the key nodes, and this is what you should check first:

• 🔋 Battery: Measure the voltage with a multimeter (normal: 3.7-4.2 V). If below 3.5 V, a replacement is required.
• 📶 Antennas: Check the integrity of the wires (often rubbed at the charging connector).
• 🔌 Charging connector: Clean contacts with alcohol and check for oxidation.
• 💾 Memory chip: If the smartphone does not turn on, the contact may have gone away (a soldering iron with a thin sting is needed).

When replacing components, consider:

• 🔧 Mi 2 Lite screws of different lengths – don’t confuse them!
• 🧲 Magnetic parts (dynamics, vibrator) are sensitive to static electricity.
• 📏 The plumes cannot be bent at an angle greater than 90.°.

💡

The most common mistake in disassembling the Mi 2 Lite is to damage the touchscreen plume, which is fragile and can't tolerate multiple connections/disconnections. If the sensor stops working after assembly, check the plume first.

Step 6: Build a Smartphone

To assemble Xiaomi Mi 2 Lite need in reverse order, but taking into account a few nuances:

1. Before installing the battery, clean the contacts on the board and the battery itself with alcohol.
2. Twisting the screws cross-cross to avoid skewing the board.
3. When installing the screen, first plug the plumes and then glue it to a double-sided tape (e.g. 3M 467MP).
4. Check the operation of all buttons and sensors before final assembly.

After assembly:

• 🔋 Charge your smartphone 100% and discharge to 0% – this calibrates the battery controller.
• 📱 Reset the settings to factory (Settings) → Additionally. → Recovery and resetting if there were problems with the software.
• 🔍 Check the tightness of the body - if there are gaps, seal them with duct tape for dust protection.

⚠️ Warning: If the smartphone does not turn on after assembly, but the red indicator is lit when connecting to charging, the problem may be in short circuit on the board. disconnect the battery and check the board for foreign objects (cogs, plastic debris).

Frequent Mistakes and How to Avoid Them

Even experienced craftsmen sometimes make mistakes when disassembling the Xiaomi Mi 2 Lite, and here are the most common ones and ways to prevent them:

If you make one of these mistakes, don't panic. In most cases, you can fix the situation:

• 🔧 Scratches on the case: Camouflage them with a special pencil for plastic (color Mat Black for black version).
• 🔋 Replace the battery with a new one (recommended) BL-T08 AliExpress).
• 📱 Broken sensor: Check the plume with a multimeter - if a cliff, a replacement is required.

FAQ: Answers to Frequent Questions