Self-disassembly of the smartphone is always a balance between the desire to save on the services of the service center and the risk of damaging delicate electronics. Xiaomi Redmi Note 9S (also known as Redmi Note 9 Pro in the global market) has a fairly standard design for modern devices, but requires accuracy and a specific set of tools. Unlike flagship models, it uses a plastic frame, which simplifies the process a little, but does not make it safe for a beginner.
Before you start dismantling, you need to clearly understand the purpose of the procedure: whether it is to replace the battery, repair the charging connectors or replace a broken screen. Any interference with the case automatically deprives you of warranty service from the manufacturer. If your device is still warranty and the breakdown is not associated with mechanical damage, it is better to contact an authorized service.
In this article, we will take a closer look at the disassembly process, focusing on the nuances of working with adhesive seams and brittle plumes. We use proven techniques that minimize the risk of damage to internal components. It is important to follow the sequence of actions and not use excessive force where parts are fastened with dense glue.
💡
Before starting any work, be sure to back up all important data and turn off the device completely. Working with the phone on can lead to a short circuit.
Preparation of the workplace and necessary tools
You can't do a good job of disassembling without a properly organized space, you need a spacious table with good lighting, where nothing will distract you, and the surface has to be clean, dry, and, preferably, antistatic, to eliminate the risk of static discharge that could disable the chips.
The basic toolkit for working with Xiaomi Redmi Note 9S includes several specific items. Standard home screwdrivers will not work here, as the screws have different threads and sizes.
- 🔧 Precision screwdrivers (cross-hatched) PH000, PH00 flat)
- 🔥 Hair dryer or heating pad for heating the back cover (temperature) 80-100°C)
- 💳 Plastic mediators, sucker and thin metal scalpel
- 🧲 Magnetic mat or organizer for screws
- 🧴 Isopropyl alcohol and tweezers with dielectric linings
Special attention should be paid to heating. The Redmi Note 9S rear panel is glued around the perimeter, and without prior warming, you risk breaking glass or plastic when you try to detach. Don't use an open fire, only controlled heating.
Rear cover removal and primary access
The process of opening the body begins with the removal of the tray for SIM-This is a must-do step that is often overlooked, which can damage the tray or motherboard when heated. Use a clip or a special key included in the delivery kit.
After removing the tray, warm the perimeter of the back cover. distribute heat evenly along the edges of the device for 2-3 minutes. Do not hold the hair dryer at one point for too long so as not to damage the display on the back side or the internal components from overheating.
⚠️ Warning: Do not heat the center of the back cover, where the camera and main board are located. This can damage the sensors and bloat the battery.
When the body is sufficiently warmed, place a suction cup at the bottom of the back panel. Pull up a little bit, create a small gap, and gently insert a plastic mediator into it. Drive the instrument along the perimeter, cutting the adhesive layer. Move slowly, feeling the resistance of the adhesive.
Disconnection of the battery and removal of the protective plate
Once the back cover is successfully removed, you will see the inside of the smartphone, and the first thing you need to do is disconnect the battery from the motherboard, a critical safety step that prevents short circuits when working with other components.
The battery in the Xiaomi Redmi Note 9S is connected by a wide plume covered by a metal protective plate, which is mounted by several screws of different sizes. When you unscrew (remember) the location of each screw, as they can vary in length.
Use tweezers or a plastic blade to turn off the connector, and the movement should be directed strictly upwards, parallel to the plane of the board, and do not swing the connector from side to side, so as not to damage the contact pads on the motherboard itself.
- 🔋 Disconnect the main battery plume first
- 📱 Check for no residual voltage (indicators should go out)
- 🔩 Carefully fold all screws in order of their removal.
Only after the power is turned off can the internal modules be disassembled further, and ignoring this rule can lead to irreversible consequences for the power controller.
☑️ Safe disassembly
Removal of motherboard and modules
The Redmi Note 9S motherboard is located at the top of the body and is covered by a massive metal frame-screen, and to remove it, you need to twist all the visible screws around the perimeter and in the center, some screws can be hidden under stickers or plugs.
Once you remove the metal, you'll have access to the main connectors, which are the plumes of the display, the touchscreen, the main cameras and the side buttons, each with its own protective press, which you also need to dismantle.
Be very careful when handling camera plumes, which are very thin and easily break when handled carelessly, and use tweezers to capture only the hard part of the connector, but not the flexible track itself.
| Component | Location. | Type of attachment | Risk of damage |
|---|---|---|---|
| Main camera. | Upper left corner | Plug + Plug | Tall (fragile lens) |
| Display plume | The bottom of the fee | Wide plume | Medium (breaks when jerked) |
| cable | Right edge | Round connector | Low (it's important not to squeeze) |
| Vibromotor | Lower part of the hull | Shore + Clay | Low. |
When removing the board from the case, be careful of the antenna cable, which often runs through the entire case and connects to the board from the bottom. It must be gently snapped from the main module before being fully removed.
The secret of antenna cable
Working with the bottom pallet and charging connector
The bottom of the smartphone contains a charging connector (USB Type-C), microphone, speaker and antenna contacts, access to this node opens after removing the main board, but often requires special care during dismantling.
The charging board in the Xiaomi Redmi Note 9S is mounted with multiple screws and connected to the main board through a long plume running along the body. This plume can be glued to the frame, so it needs to be carefully separated, heating the dryer of the sticking place.
⚠️ Warning: The charging plume is very thin. When you replace it, try not to bend it at a sharp angle or pull it with force. It is better to unplug it completely and install a new one than risk the integrity of the old one.
Also in this compartment is the main speaker, which can be glued to the body, and to extract it, use a hair dryer and a thin line or a plastic map, metal tools can damage the speaker membrane.
- 🔌 Check the status of the contact areas of the charging connector
- 🧹 Clean the speaker compartment of dust and pile
- 📡 Make sure that the antenna’s spring contacts are clean and not oxidized.
Often, charging or sound problems are solved by simply cleaning the contacts or replacing this inexpensive module, making this stage of repair the most sought after.
💡
Replacing the charging connector is one of the most common causes of disassembly. Always check the integrity of the plume before buying a new part, as the problem may be in the cliff.
Removal of the display and frame (screen module)
The display module in the Redmi Note 9S is glued to a plastic bezel. If your goal is to replace the screen itself, you don't have to remove all the insides if you change the module assembly with a frame, but professional repainting requires a complete dismantling.
The screen is fixed by a powerful adhesive layer around the perimeter. Heat the front of the device (carefully without overheating the matrix), and use a suction cup and mediators to separate the glass from the frame. The movements should be progressive and smooth.
Underneath the screen is a touchscreen board and plumes. Be very careful: the AMOLED matrix (in some versions) or IPS is very fragile. Any pressure with your finger can leave black spots or break the matrix.
After the module is separated, you need to transfer all the small elements (dynamics, vibration, button plumes) from the old frame to the new one, which is the most time-consuming step, requiring patience and accuracy.
💡
Use a special adhesive B-7000 or T-8000 to assemble. Apply it with a thin strip, avoid getting glue on the cameras and connectors. Let the glue dry slightly (1-2 minutes) before joining the parts.
Assembly of the device and verification of functionality
The assembly is done in a strictly reverse sequence: Start by putting the display on the frame (if you have changed it), then put the motherboard back in place, plugging all the plumes in, and only after all the components are mechanically installed, the battery is connected.
Before you twist the screws and close the case, it is recommended to conduct an initial test, turn on the device and check the touchscreen, sound, cameras, vibration response and charging, which will save time in case some plume was not fully connected.
The final step is to apply a new adhesive layer to the back cover and install it. Use rubber harnesses or heavy books to press the cover evenly during the drying of the adhesive (usually 1-2 hours).
⚠️ Warning: Do not turn the device on immediately after assembly if you have used liquid glue.Adhesive vapors can condense inside and damage the optics of cameras or speakers.
A properly assembled Xiaomi Redmi Note 9S should not have backlashes, creaks or gaps between the screen and the frame.All screws should be twisted, but without fanaticism, so as not to disrupt the thread in the plastic.