How to glue protective glass on Xiaomi Redmi 9: a step-by-step guide with photos and tips

Why the protective glass on Xiaomi Redmi 9 is not a luxury, but a necessity

The screen Xiaomi Redmi 9 with a diagonal of 6.53 inches and a resolution of 2340×1080 is covered with a factory protective layer, but it is far from eternal. Even with careful use of micro scratches appear after 2-3 months: sand in the pocket, keys, accidental impacts on hard surfaces. Replacing the display on this model costs 5-7 thousand rubles — almost a third of the cost of a new smartphone. So the protective glass becomes a mandatory accessory that prolongs the life of the screen.

But not all glasses are equally useful. Cheap PET films scratch and turn yellow quickly, and poor-quality glass patches can degrade sensor sensitivity by 15-20% due to the wrong thickness or adhesive layer. In this article, we will discuss how to choose the right glass for Redmi 9, prepare the surface of the screen and glue it without bubbles and offsets - the first time.

What kind of protective glass is suitable for Xiaomi Redmi 9: types and characteristics

There are three main types of protective glass on the market, and each has its own pros and cons for the Redmi 9:

• 🔹 2D-The glass is flat, covers only a flat part of the screen, does not go to the curved edges. The most budget option (from 200 rubles), but leaves the side faces of the display unprotected.
• 🔹 2.5D-glass with rounded edges, repeats the shape of the Redmi screen 9. It's more expensive (400-800, but better protects against scaling when falling.
• 🔹 3D-Glass is a full screen covering with a bend on the ends, ideal for maximum protection, but more difficult to install and more expensive (from 1000 rubles), suitable for users who often drop their phone.

Key parameters that should be considered when choosing:

Xiaomi Redmi 9 is the best choice 2.5D-glass with a thickness of 0.3 mm with hardness 9H. It strikes a balance between protection, price and ease of installation. If you drop your phone frequently, consider options with a shock-absorbing layer (e.g. Spigen Glas.tR). EZ Fit).

Xiaomi Redmi 9 Preparation for Sticking: What You Need and How to Clean the Screen

Successful installation of the protective glass depends on preparation, and even the best glass will not lie flat if there are dust or greasy traces on the screen.

• 🧴 Alcohol solution (isopropyl alcohol 70% or wipes for cleaning screens).
• 🧻 Microfiber fabric (without pile, as for glasses).
• 🧲 Scotch or sticky tape to remove dust.
• 📏 Plastic card or special scraper for aligning glass.
• 💡 Bright lamp or flashlight for dust check.

Step-by-step cleaning the screen:

1. Turn off Redmi 9, so you can see dirt and dust.
2. Wipe the screen with a wet wipe with isopropyl alcohol, then a dry microfiber, and the movements should be circular, from center to edge.
3. Light the screen at an angle with a flashlight: all the dust particles will cast shadow. Remove them with tape, slightly touching the surface.
4. Check the edges of the screen, because there's often dirt in there. Use a toothpick wrapped in microfiber.

⚠️ Warning: Do not use household detergents (soap, glassware) - they leave a film that impairs grip. Also avoid paper towels: they scratch the screen with microparticles.

Step-by-step: how to glue glass on Xiaomi Redmi 9 without bubbles

Now, to the most critical stage, follow the instructions carefully, because each step is important for the perfect result.

Step 1: Unpacking and checking glass

Take the glass out of the package with the edges on it, check for defects, whether it's chipped, cracked, or detached, if it's double-sided (with a protective film on either side), remove only the outer film, the inner film is removed just before the glue is glued.

Step 2. Glass alignment

Carefully apply the glass to the Redmi 9 screen without removing the protective film from the adhesive side. Combine the cutouts for the speaker, front camera and sensors. If the glass is marked for positioning, focus on them. Once you make sure that everything matches, slightly press the glass in the center, it will stick due to the electrostatic effect and will not move.

Step 3: Removal of protective film and fixation

Lift the glass over one edge and remove the inner protective film. Quickly (but carefully!) apply it back, starting at the top of the screen. Use a plastic card or scraper to push the air bubbles from the center to the edges. The movements should be smooth, without pressing.

Step 4 Final check

Turn on Redmi 9 and check the sensor sensitivity: all gestures are working, there are no dead zones. Light the screen at an angle — if there are small bubbles, they will disappear in 12 to 24 hours. Large bubbles (more than 1 mm) indicate poor adhesion, in which case the glass will have to be glued.

Common Mistakes in Flushing and How to Avoid Them

Even with careful preparation, users often make mistakes that spoil the outcome, and here are the most common ones and ways to prevent them:

• 🌫️ Dust under glass - occurs if cleaning was done in a dusty room or used a villous fabric. Solution: stick the glass in the bathroom after a hot shower (the steam precipitates the dust) or use a sticky roller to remove microparticles.
• 💦 Air bubbles -- they come in when you press them unevenly, or if the adhesive layer is damaged. Solution: use a plastic card to push bubbles from center to edge. Large bubbles (more than 2 mm) tell you that the glass is broken, you need to replace it.
• 🔄 Glass displacement happens when you don't match the cutouts with the sensors. Solution: before you stick it, take a picture of the screen with the glass overlaid (without removing the protective film) and check for a match of cutouts.
• 🧴 The glue marks on the screen remain if the glass has been removed and re-adhesive. Solution: remove the glue residue with alcohol, but do not rub the screen with force - this will damage the oleophobic coating.

⚠️ Note: If the Xiaomi Redmi 9 sensor becomes less sensitive after gluing (for example, light touches do not work), most likely the glass is too thick (more than 0.35 mm) or with a defect in the adhesive layer.

💡

Before you stick it, turn on Redmi 9's "Do Not Disturb" mode and turn off the vibration, so you avoid accidentally touching the screen while installing the glass.

How to Care for a Safety Glass to Last Longer

The life of the protective glass on Xiaomi Redmi 9 depends not only on the quality of the material, but also on the care. Follow these tips to ensure that the glass retains its properties for a long time:

• 🧼 Cleaning – use only microfiber wipes and special liquids for screens. Avoid paper wipes and alcohol of high concentration (over 70%) – they destroy the oleophobic coating.
• 📵 Storage - do not put your phone down on hard surfaces (table, window sill). 9H-glass can crack with a point impact.
• 🔋 Charging - avoid using your phone while wirelessly charging. heating to 40°C+ can deform the glue layer of glass.
• 🛠️ Repair - if the glass cracks, replace it right away.The chips not only spoil the look, but also accumulate dirt that scratches the original screen.

The average lifespan of quality glass is 6-12 months, if you notice that:

• oleophobic coating ceased to repel fat (fingerprints remain even after rubbing),
• There are deep scratches that cling to the finger.
• And the glass started to peel off at the edges.

Remember, the safety glass should protect, not degrade, the user experience.

💡

The oleophobic coating of glass wears out faster than the glass itself. If the screen gets sticky and gets dirty quickly, it doesn't mean the glass has cracked, it's just time to upgrade it.

What to do if the glass cracked or peeled off: emergency measures

Even the strongest glass can crack when it hits hard.

1. Lock chips - paste over the crack scotch (transparent or paint) so that the fragments do not crumble and scratch the screen.
2. Do not press the crack – this may cause further cracking or damage to the display.
3. Replace the glass for 2-3 days – the longer you walk with cracked glass, the higher the risk of dust getting under it and scratching on the original screen.

If the glass has started to flake off at the edges, try the following methods:

• Warm up the edge with a hair dryer (temperature no higher than 50°C) and press the glass with a plastic card. The glue layer can melt and grab again.
• Apply a thin layer of cyanoacrylate glue (superglue) around the edge with a toothpick. Remove the excess with alcohol immediately.
• If the detachment is more than 5 mm, it is better to replace the glass - temporary measures will not return the original strength.

⚠️ Warning: If dust or moisture is trapped under the detached glass, don't try to glue it back. The dirt particles will turn into an abrasive and scratch the original screen when pressed.

FAQ: Answers to Frequent Questions About Security Glasses for Xiaomi Redmi 9