How to properly glue the protective glass on Xiaomi Redmi 9A: photo-hacking

Security glass on Xiaomi Redmi 9A — It's not a luxury, it's a necessity. Even a budget smartphone with a 6.53-inch screen. HD+ It's vulnerable to scratches from keys in your pocket or falling on asphalt, but many users are faced with a problem: after gluing, bubbles appear, the glass moves away at the edges or sensors interfere with the work. It's all about the application technology - every little thing is important here, from the choice of material to the microclimate in the room.

This article isn't just a retelling of instructions out of the box, but we're going to break down the hidden nuances of sticking for Redmi. 9A, What glass manufacturers are silent about: how to avoid the effect of a “rainbow” on an oleophobic coating, why the glass may not stick to the edges the first time, and what to do if a speck of dust falls under it. And also – test 5 popular brands of glass (from Spigen to no-name) for compatibility with the sensor approach of this smartphone.

Spoiler: 90% of the problems are due to improper screen preparation, even if you bought premium glass with a high-end screen. 9H Hardness, but ignored the cleanup UV-And then we glue it, and it's going to be bad. 9A One thing that's special about this is that because of the convex front camera module, standard windows often don't cover the entire screen, leaving vulnerable areas on the sides.

1.What kind of protective glass to choose for Xiaomi Redmi 9A

Not all glass is equally useful. - For Redmi 9A Three parameters are critically important: screen coverage, sensor compatibility and thickness. Glass thinner than 0.2 mm will not save you from strong impacts, and a thicker 0.33 mm will worsen the sensitivity of the sensor.

Pay attention to:

• 🔍 Full Coverage – should cover the entire screen, including the curved edges (but on Redmi) 9A They're minimal).
• 📱 Cut under the camera – if the glass is without a cutout, the self-sequins will be problematic due to the bulge of the module.
• 🛡️ Firmness 9H — Minimum threshold for protection against scratches with keys.
• 💧 Oleophobic coating – so that fingerprints do not remain.

From proven brands for this model are suitable:

• 🏆 Spigen Glas.tR EZ Fit – with an installer for perfect positioning, but expensive.
• 💰 Ringke Fusion-X – budget option with good adhesion.
• 🛒 AliExpress No-names are cheap, but often with defective adhesive layers.

⚠️ Attention: Glass with UV-And the glue, like the Whitestone Dome, requires a special lamp to polymerize, and without it, the glass won't stick!

Preparation for gluing: tools and conditions

You might be surprised to learn that the microclimate in the room affects the outcome.

• 🌡️ Temperature: 20-25°C (in cold, glue thickens, in heat - too liquid).
• 💧 Humidity: 40-60% (at high humidity, condensate will fall under the glass).
• 🌬️ Lack of drafts - dust flies even from the fan.

List of mandatory instruments:

⚠️ Warning: Do not use wet wipes to clean the screen – they leave a film that impairs grip!

Screen preparation process:

1. Turn off your phone and let it cool down (if you were working).
2. Take off the old film/glass, if you had any. Use the mediator to tweak the edge.
3. Wipe the screen with a dry microfiber, then an alcohol napkin in a circle (from center to edges).
4. Stick a piece of tape to the screen and sharply tear off - this will remove the microparticles of dust.
5. Check the screen under bright light: if you see divorces or villi, repeat the cleaning.

The screen is off and cooled.|

All traces of the old coating removed|

Alcohol wipes used|

Dust removed with scotch|

Lighting is bright, no shadows-->

3. Step-by-step instruction: how to glue glass without bubbles

Now, the main stage. Take your time: you have 3-5 minutes to fix the glass before the glue is grasped.

The sticking algorithm:

1. Positioning: Remove the protective film from the glass on one side only (glue). Carefully apply the glass to the screen, combining the cutouts under the camera and the speaker. Don't push, just hold the glass behind the edges.
2. Fixation: Press the center of the glass (where the Mi logo is) to help the glue spread evenly. Swipe the plastic card from center to edge, expelling the bubbles.
3. Check: Turn on your phone and check the proximity sensor (call and hold your hand to the top) and light up the flashlight at an angle, so you can see even microbubbles.

⚠️ Attention: If the glass is crooked, don't peel it off! Tap the edge with a thin thread (like a dental one) and correct it carefully.

Video instructions (if visualization is required):

💡

If the bubbles are left after gluing, put the phone under a heavy book for 12 hours, and most bubbles will disappear by themselves if they are not filled with air, but caused by uneven distribution of glue.

4 Common Mistakes and How to Avoid Them

Even the most experienced users make mistakes.-5 Mistakes in the Redmi slinging 9A:

Mistake 1: Ignoring the proximity sensor

On the Redmi. 9A The sensor is located at the top of the screen, next to the camera. If the glass is too thick or incorrectly positioned, the sensor will fire with a delay. Solution: choose glasses marked "Sensor-Friendly" or check the sensitivity before buying (read reviews).

Mistake 2: Sticking on the phone on

The screen heats up during operation, and the glue can float, which will cause the glass to shift. Always turn off the phone 10 minutes before the procedure.

Mistake 3: Using household detergents

Soap, glassware, or wet wipes leave the film. Only isopropyl alcohol 70%+ or special wipes for electronics!

Error 4: Pressure on the edges of the glass

If you press the edges hard, the glue will squeeze out and form rainbow sways, push only on the center, and smooth the edges with light movements.

Mistake 5: Gluing in a Dustful Room

Even one speck of dust under the glass will spoil the view. It is better to carry out the procedure in the bathroom after the shower (there is less dust) or use a box for gluing (sold on AliExpress for 200-300 rubles).

💡

The biggest mistake is rushing. 80 percent of marriages are due to trying to make things "quick." Plan 30 to 40 minutes for a sticker, based on preparation.

5 What to do if the glass is unstuck or bubbles appear

Don’t panic – in most cases, the situation can be fixed without changing the glass.

Problem: Bubbles around the edges

The reason: uneven distribution of glue or air intake.

Decision:

1. Heat the glass with a hair dryer (temperature 40-50)°C, no higher!).
2. Carefully tuck the edge with a toothpick and press the glass back.
3. Roll the plastic card from center to edge.

Problem: The glass is completely gone

Reason: poor adhesion (cheap glue or greasy screen).

Decision:

• Remove the glass and clean both adhesive layers (on the glass and screen) with alcohol.
• Apply a thin layer of superglue B-7000 (Just around the edges!) and press the glass.
• Place your phone under a press (such as a stack of books) for 12 hours.

Problem: "Rainbow" on screen

Reason: too thick glass or pressure on the adhesive layer.

Decision:

• If the effect appeared immediately - remove the glass and glue, without pressing the edges.
• If it's over time, it's a defect in the oleophobic coating, just a replacement of the glass.

⚠️ Warning: Do not use Moment glue or other cyanoacrylates! they will damage the oleophobic screen covering and leave divorces.

6. Safety glass alternatives: when it is not suitable

Not everyone likes glass: it adds thickness, can reduce the brightness of the screen, and is not always compatible with covers.

1. Hydrogel film.

Pros:

• 🔹 Thin (0.1 mm), not felt on screen.
• 🔹 Self-healing from small scratches.
• 🔹 Does not interfere with the work of sensors.

Cons:

• ❌ Not protective against heavy blows.
• ❌ Quickly covered with scratches from the keys.

Liquid glass (nanocoating)

Pros:

• 🔹 Invisible does not change the tactile sensations.
• 🔹 Protects against scratches (hardness 6–7H).

Cons:

• ❌ It does not save from cracks when falling.
• ❌ Requires repeated application every 6-12 months.

Tempered glass with adhesive base

The glass-film hybrid is thin (0.15 mm), but with shock protection. 9A, If you need something in between.

Comparative table:

7. How to extend the life of protective glass

Even the strongest glass wears out, so it lasts longer.

Care tips:

• 🧼 Wash Your Hands Before Using Your Phone – Fat and Dirt Destroy Oleophobic Coverage.
• 📦 Use a case with high sides (at least 1.5 mm) so that the glass does not rub against the surface when falling.
• 🔄 Once a month, wipe the glass with an alcohol napkin - this will restore the slip.
• 🚫 Do not place your phone down on hard surfaces (even glass). 9H sand-grazing).

What can't be done:

• ❌ Wash the screen with abrasives (such as soda).
• ❌ Gluing on top of the glass another film will worsen the sensitivity.
• ❌ Use metal scrapers to remove dirt.

⚠️ Warning: If there are microcracks on the glass, replace it immediately, not only do they spoil the view, but they also collect dirt, which will then be released on the screen when you shoot it.

FAQ: Frequent questions about protective glass for Xiaomi Redmi 9A