The broken back of the smartphone is not just an aesthetic defect, but also a serious threat to internal electronics. In the Xiaomi Redmi Note 10 Pro, the design is made of glass, making the device vulnerable to falls, especially at corners. Moisture or dust penetrating through cracks can lead to oxidation of contacts, battery failure or even battery bloating.
The replacement process requires precision, specific tools, and an understanding of the building principles of modern gadgets. Sealing the case is a critical step, ignoring which will turn the phone into an open system, unprotected from external factors. In this guide, we will take a detailed look at every step, from the preparation of the workplace to the final moisture protection check.
You don't have to be a professional to do this yourself, but you'll need patience. We'll look at the nuances of acrylic glue, the specifics of turning off the plumes and how to safely warm up the case, and the right approach will allow you to return the device to its original appearance and protect its contents.
Tools and workplace preparation required
Before you start dismantling, you need to organize the workspace, the surface should be clean, well-lit and preferably not conduct static electricity. Ideal antistatic mat or clean wooden table. Any small detail that falls on the carpet can be lost forever, so watch the order.
To work with the Redmi Note 10 Pro, you will need a specific toolkit that is different from the standard set for metal lids. Focus on the quality of the suction cup and the mediator, since glass requires delicate handling. Using metal blades at the initial stage can lead to chipped edges of the frame.
- 🔧 Hair dryer (building with temperature adjustment or household at maximum power)
- 🧲 Set of screwdrivers (cross-crosses) PH00, PH000 Torx T5)
- 🧩 Plastic mediators and screen suction cup
- 🧴 Clay. B-7000 or E-8000 fixing
Special attention should be paid to isopropyl alcohol, which is necessary to degrease the frame before applying a new layer of glue. Without quality surface preparation, the adhesion will be weak, and the lid may move away after a few weeks of operation, and also prepare a container with sections for screws, so that they do not confuse the assembly.
Dismantling the old back panel
The first and most important step is to safely remove broken glass. The smartphone body is glued around the perimeter, and it requires heating to soften the adhesive compound. Turn on the hair dryer and warm the perimeter of the device evenly for 2-3 minutes. The temperature should not exceed 80-90 degrees so as not to damage the internal components or the battery.
⚠️ Warning: Do not heat the central part of the case where the battery is located. Local overheating of the lithium polymer battery can cause it to swell or ignite!
After warming up, gently place the suction cup in the bottom of the back cover and pull up slightly, creating a small gap. Insert a plastic mediator into the resulting gap. Movements should be sliding along the edges, not stabbing inwards. Progress gradually along the perimeter, periodically warming the cooling areas.
Be very careful in the area of the camera module and the fingerprint scanner. Under these elements can be plumes that are easily damaged by sloppy movement of the tool. If the lid is tight, add a little more heat, but do not use excessive physical force.
💡
If the glass has split into small fragments, stick a wide transparent tape on top before heating - this will prevent the fragments from scattering and make it easier to remove the panel entirely.
When the glue is softened, the lid should be removed easily. If you feel resistance, stop and check if you have forgotten to warm up a section. A sharp jerk can lead to the breaking of the plastic elements of the frame or damage to the plume of the side button.
Disabling plumes and extracting components
When you remove the back, you have access to the main board and battery, but you can't pull the plumes right away. In the Xiaomi Redmi Note 10 Pro, many connectors are covered with metal plates or plastic plugs that need to be dismantled.
First of all, turn off the battery. It's a safety requirement for any work inside the smartphone. Find the battery connector (usually located at the bottom or middle of the board) and gently snap the connector with a plastic blade. Only after the power out can you work with other modules.
☑️ Safe shutdown
Next, disconnect the plume connecting the main board to the child (bottom) where the charging connector is located, it runs along the battery and is often fixed with additional mounts, and it is also worth turning off the tail of the side button if it interferes with the complete removal of the cover or replacement of components.
If the new back cover comes without any transferred components (camera, vibrator), you'll have to carefully remove them from the old broken panel.The cameras are attached to glue or double-sided tape, so heating them is also mandatory.
Cleaning the frame and preparation for gluing
The quality of the new lid depends on the preparation of the seat. The old frame will definitely contain residues of glue, dust and fat. Carefully remove all residues of the old adhesive using tweezers and a plastic blade. Use metal tools with care not to scratch the aluminum frame.
After mechanical cleaning, degrease the surface. Use a lilac-free wipe soaked in isopropyl alcohol. Rub it carefully, especially in the corners and around the camera module. Fat spots from the fingers reduce adhesion of the glue, which in the future will lead to moisture entering the body.
| Type of pollution | Deleting method | The risk of neglect |
|---|---|---|
| B-7000 glue residues | Mechanical (drift) + heating | Uneven fit, gaps |
| Fat spots. | Alcohol degreasing | Peeling off the lid, water ingress |
| Dust and pile | Compressed air or hand | Camera matrix dusting, creaking |
| Metal oxides | Specialty liquid or alcohol | Heat sink deterioration, corrosion |
Make sure there is no dust in the groove underneath the camera. Even a microscopic grain of sand can put pressure on the lens, causing glare in the photos or, in the worst case, a crack in the lens glass from the inside.
Installation of a new cover and sealing
The process of installing a new panel requires speed and precision. Apply the B-7000 or E-8000 glue in a thin, continuous layer all over the frame. Avoid getting glue onto electronic components, the speaker and the camera area. The layer should be uniform, without tears, to ensure water resistance (at the level of household spray).
How much glue dries?
Carefully combine the new lid with the frame, starting with the camera area. Make sure all the holes match and the gaps around the perimeter are the same. Press the panel tightly at the edges. For better fixation, you can use rubber tapes wrapping them around the perimeter of the phone, or put a light load on top (like a book) for 15-20 minutes.
⚠️ Warning: Don't turn on the phone right after assembly! 1-2 The vibration of the motor when switched on may disturb the sealing seam that has not yet become strong.
If you use a finished lid with a factory-made adhesive layer (water-activated adhesive) already applied, the procedure is simplified, so you can remove the protective film, degrease the frame with alcohol, slightly warm up the adhesive layer with a hairdryer to activate it, and press the part, a method that often provides better sealing.
Performance check and final tests
Once the glue is grasped, you can start testing, turn on the device and check the basic functions: touchscreen, vibration response, speaker sound, pay special attention to the modules that may have been affected during the disassembly — the main camera and fingerprint scanner.
Checking the fingerprint scanner is critical. In the Redmi Note 10 Pro, it's built into the on button. If the print doesn't read or read well after assembly, it may have been damaged by the plume or broken contact during assembly, and check the front and rear cameras for focus and dust in the images.
To check the tightness (conditional), you can conduct a visual inspection of the seam. Swipe your finger along the junction - there should be no sharp glue protrusions or noticeable gaps. A full water test is not recommended, since the IP53 factory moisture protection does not fully recover when self-repaired.
💡
The quality of gluing determines not the amount of glue, but the purity of the surface and the uniformity of the press in the first minutes after installation.