How to Replace or Connect a New Remote to a Xiaomi Mi TV: The Complete Guide

Why you might need to replace the remote for Xiaomi Mi TV?

The remote controls from Xiaomi Mi TVs are reliable, but even these devices fail over time, and most often users find that buttons stop responding to presses, batteries quickly discharge, or the remote control stops synchronizing with the TV at all, and in some cases, the problem lies in mechanical damage: cracks in the body, liquid pouring or falling from a height.

Another common situation is the loss of the original remote, where you have to buy a new one, but not everyone knows that not every remote from Xiaomi will fit your TV model. TV 4S It may not work with Mi. TV Q1, Even if they look the same, there are also times when the TV doesn't recognize the new remote because of a firmware failure or conflict with other devices (such as a sound bar or console).

In this article, we will discuss:

• 🔍 How to check that the problem is in the remote, not in the TV
• 🛒 What remotes are compatible with your Xiaomi Mi model? TV
• 🔄 Step-by-step instructions for connecting a new remote
• ⚡ What to do if the TV does not see the remote after replacement
• 🔧 Alternative ways to control the TV without a remote

How do you make sure the problem is in the remote and not in the TV?

Before you run to the store for a new remote, you should rule out other possible causes of malfunction.

1. Check the batteries. Even if they're new, the contacts could have oxidized, try cleaning them with an alcohol napkin or replacing them with a known working one.
2. Check the IR port of the remote. Point your smartphone camera at the LED remote control and press any button. If you see a flicker on your phone screen, is the remote working. No flicker? So the problem is in the remote itself.
3. Try rebooting the TV. Shut it off for 1-2 minutes, then turn it on again, and sometimes it helps to reset the temporary IR failures.
4. Check if there is interference. Other IR devices (air conditioners, music centers) or bright sunlight may interfere with the signal. Make sure there is no obstruction between the remote and the TV.

If after all this manipulation, the remote still doesn't work, it probably did break, but before buying a new one, you should try resetting the remote settings (if your model supports it).

1. Remove the batteries.
2. Press and hold any button (such as Power) for 10-15 seconds.
3. Put the batteries back in and try to reconnect.

⚠️ Note: Some Xiaomi Mi remotes TV (for example, for models Q1E or P1E) You don't use IR, you use Bluetooth for communication, and then you don't use the camera to check your smartphone, you just have to watch the settings on your TV.

What Remote to Buy to Replace: Model Compatibility

Not all Xiaomi remotes are universal. TV 4A Not good for Mi. TV Q2, Even if they look similar, here's the compatibility table for popular models:

If you are not sure about your TV model, you can find it:

• 📺 In settings: Settings → On TV. → Model
• 🏷️ On the back of the case sticker (e.g, L43M6-6ARU)
• 📦 In the box,

Also, pay attention to the communication protocol:

- Old models (4A/4S) frequently use IC + Bluetooth.

- New (Q1, P1, A Pro - Bluetooth only.

If you buy a remote with an inappropriate protocol, it simply will not connect.

💡

Check the reviews on the marketplace before buying, and sometimes Chinese vendors indicate incorrect compatibility "OEM".

Step-by-step: how to connect a new remote to Xiaomi Mi TV

The connection process depends on the type of remote, and below is a general-purpose instruction that is suitable for most models.

1. IR remote connection (for older models)

If your remote is using an infrared protocol (for example, MDZ-22-AB), You don't need any synchronization, it has to work right after you put the batteries in:

Connecting Bluetooth remote (for new models)

For Bluetooth remotes (for example, MDZ-26-AB or MDZ-34-AB) It requires synchronization. Here's how to do it:

1. Turn on the TV (if it is turned off, use the button on the case).
2. Put the batteries in the new remote.
3. Press and hold the Menu buttons. + OK (back + Home, depending on the model) for 5-7 seconds until the indicator on the remote starts to flash.
4. The TV will show a notification "New device detected." Confirm the connection.
5. If the notification does not appear, go to Settings → Devices → Bluetooth and select the remote manually.

If the remote is not detected:

• 🔄 Restart the TV and try again.
• 📱 Make sure there are no other active Bluetooth devices (headphones, smartphones) within a radius of 10 meters).
• 🔋 Check battery charge – some remotes require at least 80% charge for first synchronization.

3. Voice control setting (if supported)

If your remote has a Mi button AI Or the microphone, you need to activate it:

1. Go to Settings. → Voice control.
2. Select "Configure remote".
3. Follow the instructions on the screen (usually press and hold the microphone button until the beep).

⚠️ Note: On some models (Mi) TV A Pro) voice control only works when connected to the Internet, as recognition takes place on Xiaomi servers.

What if the TV doesn’t respond to the new remote?

Even when you're connected properly, you can have problems, and here are the most common causes and ways to fix them:

If nothing helps, try alternative management methods:

• 📱 Mi Remote app (available for Android and iOS).
• 🖱️ Connect the wireless mouse or keyboard through USB/Bluetooth.
• 🎮 Use a game controller (e.g. Xiaomi Game Controller).

Important: On Mi TVs TV Q1E And newer there is a hidden emergency control function - if you hold the Power button on the TV body for more than 10 seconds, a menu with basic functions will appear (volume, channels, settings).

How to use a TV without a remote: temporary solutions

If the new remote is not yet purchased and the old one is broken, there are several ways to control the TV:

1.Appendix Mi Remote

Download the official app from Google Play or App Store:

1. Connect your phone and TV to the same Wi-Fi network.
2. Open the application and select "Add device" → "Television" → "Xiaomi".
3. Follow the instructions on the screen (you may need to enter code from the TV).

The application supports all the basic functions: channel switching, volume control, application launch.

2. USB-mouse

Any wired or wireless mouse/keyboard with USB-The receiver will work with Xiaomi Mi TV:

• 🖱️ Mouse: cursor control, clicks instead of remote buttons.
• ⌨️ Keyboard: arrows for navigation, Enter instead OK, Esc instead of Back.

3. buttons on the TV body

There are physical buttons on the back or bottom of the TV (usually Power, Volume, Source) that can be used to:

• Turn on/off TV.
• Switching inputs (HDMI, AV).
• Call the menu (hold Volume for 5 seconds).

⚠️ Note: On some models (Mi) TV P1E) The buttons on the case are locked by default. To unlock them, you need to pinch Source. + Volume+ 10 seconds.

Where to buy the original remote for Xiaomi Mi TV?

Xiaomi remotes can be purchased in a number of places, but it is important to avoid counterfeiting.

• 🛒 Xiaomi official store (mi.com) - the original warranty, but the price is higher.
• 🌍 AliExpress is cheaper, but you can run into a copy.
• 🏬 Electronics stores (Svyaznoy, M. Video, Citilink) - sometimes available, but the range is limited.
• 🔧 Xiaomi Service Centers – You can order with delivery, but you will have to wait longer.

Average prices for original remotes (2026):

• MDZ-22-AB (for Mi TV 4A/4S) — 800–1 200 ₽
• MDZ-26-AB (for Mi TV Q1) — 1 000–1 500 ₽
• MDZ-34-AB (for Mi TV A Pro) — 1 500–2 000 ₽

When buying, pay attention to:

• 🆔 The articular of the remote (must match your TV model).
• 📦 Package (must be batteries and instructions).
• 🔄 Refund option (on AliExpress, select sellers with Buyer Protection").

💡

Never buy a remote marked “Universal” or “For all Xiaomi models” – they are unstable and do not support all features (for example, voice control).

FAQ: Frequent questions about replacing the remote with Xiaomi Mi TV