Replacement of wheels on a scooter Xiaomi M365: Full instructions with photos and tips

Xiaomi Electric Scooter M365 It's one of the most popular modes of transportation in the city because of its reliability and affordability, but even with a proven device, the wheels wear out over time -- especially if you're actively operating a scooter on rough roads or in rainy weather. Worn tires not only worsen ride comfort, but also increase the risk of punctures or even loss of control at high speed.

In this article, we will discuss in detail how to change the wheels on Xiaomi. M365, You will learn what tools you need, how to remove the old wheel correctly, install a new one, and avoid common mistakes, and we will also provide recommendations for choosing tires, from standard to reinforced options for extreme conditions.

If you have never repaired scooters before, don’t worry: the process of replacing wheels with scooters M365 It's easier than it sounds, and the key is to follow the instructions and not rush. To make things more clear, we've added diagrams and photos of key stages, and we've added interactive checklists and warnings about possible complications.

When is the time to change the wheels to Xiaomi? M365?

Many scooters wait until the wheel is completely worn out or torn, but it's dangerous. There are several signs that tires need to be replaced right now:

• 🔍 Visible tread wear – if the pattern on the tire is worn by more than 50%, traction deteriorates, especially on wet asphalt.
• 💥 Frequent punctures – if you pump the wheel once a week, it is a signal that the rubber has lost elasticity.
• 🔄 Uneven wear – if one wheel wears faster than the other, it can be a bearing problem or pressure.
• 🚨 Cracks or bloating – even minor damage over time leads to a tear in the tire on the go.

Average service life of standard Xiaomi wheels M365 — 1000-1500 km when driving on flat asphalt. If you often ride on gravel, curbs or in the rain, the resource is reduced to 500-800 km Reinforced tires (for example, from Honeycomb or Kenda) last 2-3 times longer, but also cost more.

⚠️ Attention: If the wheel has bloated (hernia), the replacement should be done immediately! This tire can burst at speed, which will lead to a fall.

What wheels are suitable for Xiaomi M365?

Xiaomi. M365 They have 8.5 inches in diameter and 2 inches in width, but not all tires are the same, they differ in material, tread and purpose:

For most users, the best choice is reinforced tubeless wheels (for example, Kenda). K1167 They're more expensive than the original ones, but they pay off with a long life and minimal puncture risk. If you only ride on flat asphalt, you can limit yourself to standard tires, but you can stock up on anti-piercing tape and a pump.

When buying, pay attention to rim compatibility. Some wheels (like Gotway) may not fit in the seat diameter, and check if the rim band is included, which protects the camera from damage to the spokes.

💡

If you drive on wet pavement often, choose deep tread wheels (like the Kenda K-Rad) that divert water better and reduce the risk of aquaplaning.

Tools for replacing wheels on Xiaomi M365

To change the wheel to Xiaomi M365, You'll need it:

• 🔧 Hexagons (2 mm, 3 mm, 5 mm) - for unscrewing bolts.
• 🔨 Installation blades (2-3 pieces) - to remove the tire from the rim.
• 🛠️ End key 14 mm - for the axle nut (if the wheel is rearward).
• 🔩 Screwdriver (cross) - for some models of brake pads.
• 🧴 Lubricant (WD-40 or silicone – facilitates the installation of the tire.
• 🎈 Pump with pressure gauge - to pump the wheel to the desired pressure (recommended: 35-45) PSI).

If you change the rear wheel, you will additionally need a dynamometer key (or at least control of the tightening moment), since the axle nut should be tightened with a force of 40–50 N·m. Too weak a puff will lead to backlash, and too strong – to damage to the thread.

For convenience, you can buy a special kit for repairing a bicycle (costs about 500-800). ₽). It already includes mounts, camera patches and hexagons, and if you plan to repair the scooter regularly, it's more profitable than buying tools separately.

⚠️ Warning: Do not use metal mounts without plastic tips - they can scratch the rim, which will cause camera punctures!

Buy new wheels (check size and type)|Prepare hexagons (2, 3, 5 mm)|Purchase mounting blades (plastic or silicone coated)|Prepare the pump with the gauge|Stock up on grease (WD-40 soap-solution)|If the rear wheel - find the end key for 14 mm-->

Step-by-step: how to remove the old wheel

The process of removing the wheel on Xiaomi M365 It's different for the front and the rear axles. We'll look at both.

Removal of the front wheel

The front wheel is easier to remove because it's not connected to the brake system or the electric motor.

1. Unscrew 4 bolts on the front fork with a hexagon by 5 mm.
2. Carefully remove the plastic cover (it can be glued - put it with a screwdriver).
3. Disconnect the sensor wire. ABS (If it is, it is attached to the sleeve.
4. Pull the wheel axis out of the fork. If it's sour, it'll help. WD-40.

If you plan to use it again (for example, as a spare), keep it in an upright position so that the tire does not deform.

Removal of the rear wheel

The rear wheel is harder to remove because of the brake and the engine.

1. Unscrew the axis nut with a 14mm end key. It's tightened, so you might need a lever.
2. Remove the brake pads (they are attached to two bolts under the cross screwdriver).
3. Disconnect the motor connector (it is under the plastic cover).
4. Carefully pull the axle out with the wheel. Be careful - there are bearings on the axle that may fall out!

If you're taking off the wheel for the first time, take a picture of the location of all the parts (especially the wires and brake pads) that will help you put everything back together properly.

How to Install a New Wheel on Xiaomi M365

Installing a new wheel is the reverse process, but there are a few nuances that will help avoid problems.

Front wheel installation

Follow this order:

1. Check that the bearings on the axles are clean and lubricated. If they are worn out, replace them.
2. Insert the axle into the fork and fasten with 4 bolts (tighten the cross-to-cross to avoid skewing).
3. Connect the sensor. ABS (If you have one, make sure that the sleeves are tight.
4. Set a plastic cover and snap it.

Once installed, scroll the wheel with your hand, it should rotate smoothly, without backlash or extraneous sounds. If you hear a crunch, check the bearings.

Rear wheel installation

It is important not to forget about the brake system and electrical wiring:

1. Set the wheel on the axle and make a nut (do not tighten completely!).
2. Connect the motor connector - it should click.
3. Install brake pads and adjust their position so that they do not rub against the disc, but also are not too far away.
4. Tighten the axis nut with a force of 40-50 N·m (use a dynamometer key).

After assembly, check the brake: spin the wheel with your hand and press the brake lever. The wheel should stop smoothly, without jerking. If the brake creaks or locks the wheel sharply, adjust the pads.

💡

After replacing the rear wheel, be sure to check the electronic brake (if any). To do this, turn on the scooter, spin the wheel and press the brake lever - the engine must create resistance.

How to pump the wheel and check the pressure

The right pressure in the wheels Xiaomi M365 — The manufacturer recommends maintaining pressure within 35-45. PSI (However, the optimal value depends on your weight and driving style:

• 🏋️ Weight up to 70 kg - 35-40 PSI (softer course, better depreciation).
• 🏋️ Weight 70-90 kg - 40-45 PSI (balance of comfort and controllability).
• 🏋️ Weight over 90 kg - up to 50 kg PSI (harder, but less risk of puncture).

Use a pressure pump to pump the wheels. Here's how to do it correctly:

1. Remove the cap from the nipple (it can be hidden under a plastic cap).
2. Put the pump on the nupple and lock the clamp.
3. Pump the wheel in short movements, periodically checking the pressure.
4. After reaching the desired pressure, remove the pump and quickly put on the cap (it protects the nipple from dirt).

If you have a tubeless wheel, the pumping process is more complicated: you first need to "set" the tire on the rim.

1. Grease the edge of the tire with soapy solution.
2. Pump the wheel to maximum pressure (usually 60–80) PSI).
3. Press the wheel sharply - cotton should be heard (this is the tire sat on the spot).
4. Lower the air to the working pressure.

⚠️ Note: Do not pump wheels above 50 PSI (If it's not a tubeless tire when landing! This can cause the camera to rupture or rim damage.

Common mistakes when replacing wheels and how to avoid them

Even experienced scooters sometimes make mistakes that cause new wheels to break or wear out quickly, and the most common ones are:

• 🔧 Wrong nut tightening -- too weak leads to backlash, too strong leads to thread failure. Always use a dynamometer key.
• 🔄 The entangled wires of the motor -- if you plug the connector incorrectly, the scooter won't drive or brake!
• 🛞 Ignoring bearings - if worn out, the new wheel will have difficulty rotating. lubricate or change bearings with each wheel change.
• 💨 Incorrect pressure – too low pressure increases the risk of punctures, too high – makes riding stiff.
• 🔩 Lost bolts or washers – always check if all parts are in place before assembly.

Another common problem is the uneven wear of the new wheel, which happens if:

• The wheels are pumped with different pressures.
• The bearings of one of the axles are worn out.
• You often brake only with the rear brake or only with the front brake.

To extend the life of new wheels, follow these rules:

• 🔄 Check your blood pressure regularly (every 2 weeks.
• 🚿 Avoid driving in puddles - water gets into bearings and accelerates their wear and tear.
• 🛑 Do not brake sharply at high speed – it erases the tread.
• 🔧 Once every 3 months check the tightening of nuts and the condition of brake pads.

1. wheel balance (possibly the tire is set curve).

2. Puff up the axis nuts.

Condition of bearings (they may have failed during dismantling).-->

FAQ: Frequent questions about replacing the wheels with Xiaomi M365