Replacement of the screen with Xiaomi Mi Band 5: detailed instructions with photos and videos

Broken screen on Xiaomi Mi Band 5 is one of the most common breakdowns faced by owners of this popular fitness bracelet: dropped on the pavement, accidentally pressed the door or just found cracks after wearing — the reasons can be different, and the result is the same: an unreadable display, broken sensors or a complete failure of the device. Fortunately, you can replace the screen on the Mi Band 5 without resorting to expensive service center.

In this article, you will find a step-by-step photo guide, a list of tools you need, tips for choosing parts and answers to frequent questions. We will discuss how to carefully disassemble the bracelet without damaging the internal components, how to connect the new screen correctly and what to do if the device does not turn on after replacing, and you will learn why the original screens for the Mi Band 5 are often sold with a touchpad - and whether you can do without replacing it.

Causes of Screen Breakage and Signs of Failure

The Xiaomi Mi Band 5 is made of tempered glass, but even it can't withstand heavy mechanical stress. Here are the most common reasons for the display to fail:

• 💥 Falling on a hard surface (asphalt, tiles, concrete) Even from a height of 1 meter, the screen can crack.
• 🚪 Clashing in doors, drawers or bags. Pressure on the body often leads to microcracks.
• 💦 Moisture falling under glass, despite water protection 5 ATM, over time, the seals wear out.
• 🔥 Overheating or hypothermia: Abrupt temperature changes (for example, if you leave the bracelet in the sun in the car) can deform the adhesive base of the screen.

How do you know if the screen is broken and needs to be replaced?

• 🔍 Cracks or chips on the surface of the display, even if it is still working.
• 🖥️ Image artifacts: stripes, flickering, incorrect color reproduction.
• 👆 The sensor is not working (or only responds to a part of the touch).
• ⚫ Black screen with backlight running (vibration heard, but no image).

⚠️ Warning: If the bracelet stopped turning on after falling, the problem may not be in the screen, but in the disconnected battery or damaged board.

Before you order a new screen, check the bracelet's performance by plugging it into a charger. If the charging indicator is on and the screen is still black, it's likely the display or plume is the problem.

What tools will be needed to replace the screen

The Mi Band 5 screen doesn’t require professional tools — a minimum set that can be bought from any electronics store or ordered from AliExpress — is enough.

If you don't plan to do repairs regularly, you can do without a hair dryer - the glue is softened and the usual household hair dryer at minimum power. The main thing is not to overheat the body, so as not to damage the battery.

Also useful:

• 🧴 Alcohol or liquid to remove varnish - to clean contacts.
• 📦 Container for small parts - so as not to lose cogs.
• 🔍 Lupe or magnifying glass - for working with small elements.

⚠️ Warning: Do not use metal blades or knives to disassemble the body! they leave scratches on the plastic and can damage the plumes inside the bracelet.

💡

Before starting work, take a picture of each stage of the disassembly on the phone - this will help to properly assemble the bracelet back if you forget the location of the parts.

Where to buy a screen for Xiaomi Mi Band 5: original vs analogues

There are two types of screens on the market for the Mi Band 5: the original ones (OEM) The first ones are manufactured in the same factory as the parts for Xiaomi, the second ones are copies from third-party manufacturers.

The original screens are usually sold with a touchpad, as they are soldered together, and this is due to the design of the bracelet: the display and sensor in the Mi Band 5 are a single module.

• 🔹 Accurate match in size and connectors.
• 🔹 Preservation of factory color reproduction and brightness.
• 🔹 Longer serves without artifacts.

Non-original screens are cheaper, but have a number of disadvantages:

• 🔸 Color temperature may vary (e.g., bluish tint).
• 🔸 The sensor may work less clearly (delays, false positives).
• 🔸 Faster wear (the appearance of broken pixels after 6-12 months).

Where to look for parts:

• 🛒 AliExpress is the biggest choice, but it's a long wait (2-4 weeks) and look for sellers with a rating above 98% and reviews with photos.
• 🛒 Ozon/Wildberries — fast delivery, but the prices are higher 20–30%.
• 🛒 Local service centers – sometimes sell parts in bulk.
• 🛒 Groups in VK/Telegram — You can find used screens from donor bracelets.

Average screen prices for Mi Band 5 (2026)

• Original (with touchpad): 800–1500 ₽.
• Non-original (Chinese analogue): 400-800 ₽.
• B/u original: 300-600 ₽ (risk of hidden defects).

Step-by-step instructions for replacing the screen

Now, to the most important thing, disassemble the bracelet and install a new screen, follow the instructions carefully so that you don't damage the internal components.

Step 1: Preparation and disassembly of the hull

1. disconnect the bracelet from charging and remove the capsule from the strap.

2. Heat the body with a hair dryer (temperature) ~50–60°C) for 1-2 minutes to soften the glue. Keep the dryer 10-15 cm away so as not to melt the plastic.

3. Insert a plastic blade into the gap between the front panel and the body (start at the button side). Carefully swipe the shoulder blade around the perimeter, separating the screen.

Disconnected from charging.|Straps off.|Tools prepared|The original view is photographed|Heated body with a hair dryer-->

Step 2: Disconnect the screen plume

1. Once you remove the front panel, you will see a board with a battery and a screen plume. Carefully disconnect the plume, tweezing it with tweezers for a black lock (don't pull the wires!).

2 If the screen is glued to the body with double-sided tape, remove the glue residues with alcohol or acetone.

Step 3: Install a new screen

1. Try on the new screen to the housing. Make sure that the plume connector matches the nest on the board.

2.Aply a thin layer of glue B-7000 At the edge of the screen (not on the board!) Press the screen against the case and hold for 1-2 minutes.

3. Connect the plume back, locking the black lock.

Step 4: Build the bracelet

1. Check the screen by connecting the bracelet to charge. If there is an image but the sensor is not responding, reconnect the plume.

2 Close the body, gently pressing the edges. If necessary, warm up the hair dryer for better fixation.

💡

If the screen flashes or shows artifacts after replacing, the problem may be poor plume contact. Try to clean the contacts with alcohol and reconnect the plume.

⚠️ Warning: Don't turn on the bracelet immediately after assembly! Let the glue dry for 10-15 minutes, otherwise the screen may move away.

Frequent Mistakes and How to Avoid Them

Even if you change the screen carefully, you can make mistakes that will lead to a new breakdown, and here are the most common ones and ways to prevent them:

Another common problem is that the sensor will not work after being replaced, and this happens if:

• 🔌 The plume is not connected to the end (check the locker).
• 🧲 The screen is unoriginal and incompatible with firmware (you need to update the software).
• 💧 Under the sensor got moisture or glue (disassemble and dry).

If the bracelet does not turn on after replacement, check:

1. Is the battery plume connected to the board?
2. Are the contacts closed (check the fee for foreign particles).
3. If the device is charged (connect to the USB And wait 10 minutes).

Alternative ways to repair the screen

Replacing the screen isn't the only way to bring the Mi Band 5 back to life, but in some cases, you can do it with less radical methods.

1. Repair cracks without replacing the screen

If the cracks are shallow and do not interfere with the sensor, you can:

• 🛡️ Applying transparent nail polish to cracks will prevent them from spreading.
• 📱 Use a protective film (e.g., from Mi Band 6, trimmed in size).
• 🔥 Warm up the screen with a hair dryer 70-80°C for 5 minutes – sometimes it “cures” microcracks (the effect is temporary).

2. Replace only glass (if the matrix is intact)

If only the outer glass is broken and the sensor and the matrix are working, you can only replace the glass panel.

1. Heat the screen to 60-70°C to separate the glass from the matrix.
2. Carefully remove the shards with tweezers.
3. Stick the new glass on a double-sided tape (thickness 0.1-0.15 mm).

This repair will cost less (glass costs 200-400) ₽), But it requires jewellery precision.

Purchase of a used bracelet for spare parts

If your Mi Band 5 has multiple breakdowns (e.g., a broken screen) + If you have a broken battery, you'll be better off buying a used battery bracelet with a dead battery but a whole screen, and on Avito or in thematic groups, they sell for 300 to 800. ₽.

💡

Before you buy a used screen, ask the seller to send a video showing the sensor, often showing no defects in the photos, and the video shows delays or dead zones.

Should I contact the service center?

Replacing the screen by yourself costs 500-1500 ₽ (depending on the spare part, while the service center will take 1500-2500 for this service ₽. However, there are times when it is better to trust professionals:

• 🔧 You have no experience with small electronics.
• 🔋 The bracelet is not turned on after falling (possibly damaged charge).
• 💧 Water is in the case, and the screen is not the only problem.
• ⚡ Requires a warranty for repair (in the service give 1-3 months).

Advantages of the service center:

• ✅ Use original spare parts.
• ✅ Check the operation of all sensors after repair.
• ✅ They give you a job guarantee.

Disadvantages:

• ❌ It's 2-3 times more expensive.
• ❌ Sometimes you have to wait 3-7 days.
• ❌ Risk of running into an unfair service (take a photo of the bracelet before handing over).

If you decide to give the bracelet for repair, choose services with:

• 📌 Reviews on Yandex.Maps or 2GIS (rated above 4.5).
• 📌 Guarantee of at least 3 months.
• 📌 You can check the bracelet after repair.

FAQ: Answers to Frequent Questions