The broken screen on Xiaomi Mi Band 6 is one of the most common breakdowns experienced by the owners of this fitness bracelet, dropped on the pavement, accidentally pressed the door or just found cracks after wearing — the reasons may be different, but the result is the same: an unreadable display that prevents you from using the device. The good news is that you can replace the screen on the Mi Band 6 without resorting to the services of service centers. In this article, we will discuss the entire process, from the selection of spare parts to the final assembly, taking into account the typical errors and nuances of a particular model.
It's important to understand that replacing the screen with the Mi Band 6 requires neatness and minimal skill with small electronics. Unlike smartphones, where the display is often glued to the body, here the screen is connected to the board with a flexible plume that is easily damaged if you carelessly handle it. If you've never disassembled the gadgets before, practice on an old bracelet or watch video disassembly before you start working, we will also tell you how to check the health of the new screen before final assembly to avoid reassembly.
The cost of the original screen for the Mi Band 6 in 2026 ranges from 800 to 1500 rubles depending on the seller, and in the service center for the replacement will take another 1000-2000 rubles. Self-repair will cost less, but will require time and attention. If you are ready, we will proceed!
1. What tools will be needed to replace the screen
Before you disassemble the Xiaomi Mi Band 6, prepare everything you need. Without the right tools, you risk damaging the body, the plume, or the board itself.
- 🔧 Plastic blade or mediator to gently lick the lid. Metal tools can leave scratches.
- 🔨 Thin screwdriver (cross, 1.5-2 mm) - for unscrewing screws inside the body.
- 🧲 Magnetic mat or container – so as not to lose small parts (screws, springs).
- 🔍 Lupe or magnifying glass – plumes and contacts on the board are very small.
- 🧴 Isopropyl alcohol (90%+) — Clean contacts if the screen does not respond after replacement.
- 📦 New screen for Mi Band 6 – only from a proven source (more on this below).
In addition, the following may be useful:
- 🧷 Tweezers - for working with plumes.
- 🔥 Hair dryer or thermoair station - if the screen is glued (some Mi Band 6 batches use glue).
- 📏 Plastic tweezers – to avoid damaging flexible parts.
If you don't have soldering experience, don't try to unplug the screen plume yourself -- 90% of the time, it damages the contacts on the board. In the Mi Band 6, the plume is attached with a connector that can be neatly detached without soldering.
⚠️ Warning: Don't use a knife or other sharp objects to open the case! Mi Band 6 plastic is soft and easily scratched.If there's no plastic shoulder blade, take an old bank card.
2. How to choose the original screen for Mi Band 6
The quality of the part depends on whether the bracelet will work after being replaced, and there are many fakes on the market that either don't display color correctly or stop responding to touch after a week.
| Criteria | Original | Fake. |
|---|---|---|
| Packaging | Tight box with the Xiaomi logo, protective film on the screen | Plastic bag without marking or with a blurred logo |
| schleife | Flexible, with clear marking of contacts, without creases | Hard, with uneven edges, possible microcracks |
| Display. | AMOLED, clear colors, no broken pixels | Dull colors, possible stripes or flickering |
| Price. | From 800 to 1500 rubles (2026) | Less than 600 rubles - a high probability of counterfeiting |
Where to buy:
- 🛒 Xiaomi dealers are the most reliable option, but more expensive.
- 🌍 AliExpress – Look for sellers with a rating above 98% and reviews about compatibility with Mi Band 6.
Before buying, check with the seller:
- 📋 Compatible with your bracelet version (are there any differences between the Mi Band 6 for China and the global version).
- 🔄 The possibility of returning if the screen is defective.
- 📦 Presence of protective film on the display (it is better not to remove it before installation).
3. Step-by-step disassembly of Xiaomi Mi Band 6
Now, to the most critical stage, disassembling the bracelet, follow the instructions carefully so that the internal components are not damaged.
Step 1: Remove the capsule from the strap
Carefully pull the bracelet capsule away from the strap. It's mounted on two latches -- don't put too much effort into breaking the plastic locks. If the strap is tight, put a plastic blade on the side.
Step 2 Removal of the back cover
The lid on the Mi Band 6 is held on the latches and sometimes on the glue. Insert a plastic blade in the gap between the body and the lid (start from the side of the charging connector) and carefully lead around the perimeter. If the lid does not respond, heat it slightly with a hairdryer (not higher than 60).°C) to soften the glue.
Disable the bracelet from the Mi Fit app
Charge the battery at least 30%
Prepare the workplace (clean surface, good lighting)
Take a picture of each step of disassembly (useful for reverse assembly)-->
Step 3: Spinning the screws
Under the lid, you'll see 4 small screws. Use a cross screwdriver of the right size (usually). PH00). Unscrew them diagonally so you don't skew the board. Put the screws on the magnetic mat so you don't lose them.
Step 4: Extracting the fee
Carefully raise the board by the edge, disconnecting it from the body. Be careful, there's a vibrating motor attached to the board and a screen plume. Don't pull the plume!
Step 5: Disconnect the screen plume
The plume is attached to the board with a latch connector. Raise the latch up (you can use tweezers), then carefully pull the plume out. Don't rot it or pull the wires!
⚠️ Attention: If the plume doesn't detach, don't use force. Check if the latch is fully raised. In some versions of the Mi Band 6, the connector can be glued -- in which case, gently put a plastic blade on it.
4. Installation of a new screen and assembly of the bracelet
When the old screen is disconnected, we start installing a new one, which is a very careful step, because the plume is very fragile.
Step 1. Connect the plume
Insert the new screen plume into the circuit board connector to the point. Make sure the contacts match (the plume and the board have tags). Then click the lock down. If the plume dangles, press it gently with your finger.
Step 2: Checking the performance
Before final assembly, be sure to check the new screen. Connect the bracelet to charge (without closing the case!) and wait for the switch to turn on.
- 🔄 Check if the plume sits tightly in the connector.
- 🧴 Wipe the contacts on the plume and board with isopropyl alcohol.
- 🔋 Make sure the battery is charged (minimum 10%).
Step 3: Assembly of the hull
If the screen is working, start the assembly in reverse order:
- Put the board back into the case, making sure the vibrating motor is in place.
- Turn the screws (do not pull!).
- Close the back cover, gently pressing it around the perimeter.
- Insert the capsule into the strap before clicking.
Step 4 Final check
After assembly:
- 📱 Sync your bracelet with Mi Fit or Zepp app.
- 🔍 Check the sensor for responsiveness (scrolling through the menu, touching).
- 🔋 Make sure the vibration and charging work.
💡
If the screen flickers or displays artifacts after replacing, try reconnecting the plume. Often the problem is solved by re-installation.
5. Common Mistakes and How to Avoid Them
Even with careful operation, you can make mistakes that will cause the bracelet to malfunction, and here are the most common ones and ways to prevent them:
- 💥 Damage to the plume -- don't rot it, don't pull the wires. Hold it only on the hard part at the connector.
- ⚡ Static electricity -- touch a metal object before work to remove statics. It can damage the board.
- 🔩 Twisted screws - twist them without effort, otherwise you can tear the thread in the plastic case.
- 🔋 Battery discharge - if the bracelet runs out during assembly, the firmware may be lost.
- 🧲 Loss of screws – use a magnetic mat or container with compartments.
If the screen does not work after replacement:
- Check the connection of the plume (most often the problem is this).
- Make sure the new screen is compatible with your Mi Band 6 version.
- Try resetting the bracelet to factory settings via Settings → Resetting in annex.
What if the screen does not turn on after replacement?
6. Alternative ways to repair the screen
If replacing the screen seems too difficult or expensive, consider alternative options:
- 🔧 Repair in the service center - will cost 1000-2000 rubles, but gives a guarantee (usually 3-6 months).
- 🛠️ Buy used bracelet - on Avito or Yula you can find a working Mi Band 6 for 1500-2500 rubles.
- 📱 Use without screen – if the sensor works, you can control the bracelet through the app (but it’s inconvenient).
- 🆕 Upgrade to a new model - Mi Band 7 or Mi Band 8 cost from 3000 rubles and have improved screens.
If you decide to give the bracelet for repair, choose a service with good reviews.
- 🔧 Do they use original parts?
- 🕒 Repair period (usually 1-3 days).
- 💰 Cost of diagnosis (sometimes included in the price of repair).
💡
Self-replacement of the screen on the Mi Band 6 will cost 2-3 times cheaper than service repair, but requires care. If you are not confident in your abilities, entrust the work to professionals.
7 How to extend the life of the screen after replacement
To make the new screen last longer, follow these tips:
- 🛡️ Stick a protective film – even if the screen already has a factory film, additional protection will not hurt.
- 🚫 Avoid hitting – remove the bracelet when practicing contact sports (boxing, basketball).
- 💦 Do not wet the bracelet in hot water – it can damage the glue that locks the screen.
- 🔋 Do not allow full discharge – this reduces battery life and can cause screen failures.
- 🧴 Clean the case regularly - dirt under the button can get inside and damage the plume.
If you are actively involved in sports, consider buying a silicone case for the Mi Band 6. It protects the screen from scratches and bumps, and costs only 200-300 rubles.