Xiaomi Redmi 5 Plus (codenamed vince) remains a popular smartphone even 6 years after its release — thanks to reliable filling and the possibility of inexpensive repairs. But the most vulnerable part of any phone is the display: cracks, “sweeps”, broken touchscreen or backlights force users to look for ways to replace. In this article, we will discuss how to change the screen on the Redmi 5 Plus with your own hands without damaging the fee or plumes, and also talk about the pitfalls that await beginners.
It's important to understand that replacing the display module with a Redmi 5 Plus is not as easy as it might seem. There is no removable back cover (unlike the flagships with a glass-sandwich design), and the screen itself is glued to the frame and connected to the motherboard with fragile plumes. Mistakes in the dismantling or connection of the new module can lead to a loss of touchscreen sensitivity, flashback or even a short circuit. So if you have never held a screwdriver for your phones, you better contact the service if you decide to follow our unique features.
The cost of the original display module for Redmi 5 Plus in 2026 ranges from 2,500 to 4,000 rubles (depending on the supplier and availability). OCA-Chinese analogues can be found cheaper — from 1,200 rubles, but their quality often leaves much to be desired: dim lighting, “dead” areas of the touch screen or distorted colors. OEM From trusted sellers, it will save you nerves and time.
Preparation for replacement: tools and details
Before you start disassembling, make sure you have everything you need. Redmi 5 Plus does not require super-specialized tools, but you should not save on quality - cheap plastic blades can break at the most critical moment.
Here is the minimum set you will need:
- 🔧 A set of screwdrivers with Phillips bits #00, Torx T3/T4 and Y00 (board-pin).
- 📱 Plastic blades (preferably metallic with rounded edges - they scratch the frame less).
- 🔥 Hair dryer or thermo-air station (for softening the glue - temperature 60-80)°C).
- 🧲 Magnetic mat or screw container (so as not to lose small details).
- 🔌 Tweezers with curved ends (for neat detachment of plumes).
- 🛡️ Protective gloves (optional, but recommended – glue and glass dust are harmful to the skin).
- 📦 New display module (with verified backlight and touch screen).
- 🧴 Clay. B-7000 or T-7000 (fixate).
If you buy a display separate from the frame (glass only) + And you have to be prepared to glue it to the old frame, which is harder than putting the finished module together. + frame + Experienced craftsmen advise beginners to take Full Assembly - so the risk of damage to the plumes is minimal.
⚠️ Warning: Do not use a household hair dryer to heat up the glue at maximum power! overheating above 90°C can damage the battery or melt plastic clips inside the case. Optimum temperature is 70-80°C, distance to the phone - 5-7 cm.
Disassembly Xiaomi Redmi 5 Plus: step-by-step instructions
Start by turning off the phone and retrieving it. SIM-We're going to do it carefully, and every step is important!
Step 1 Heating the housing and removing the back cover
- 🔥 Turn on the hair dryer and evenly warm the back cover of the phone for 2-3 minutes. Pay special attention to the edges - there the glue holds stronger.
- 🪛 Insert a plastic blade into the gap between the lid and the frame (start at the bottom edge where the charging connector is). Carefully drive the blade along the body, separating the clips.
- ⚠️ Don't put too much effort -- if the lid doesn't lend itself, warm it up again. Broken clips will have to be glued or replaced.
Step 2. Battery disconnection
- 🔋 Once the lid is removed, first of all, turn off the battery by putting a plastic blade on the power supply, which will prevent short circuits from further disassembly.
- 🔧 Unscrew 8 screws that fix the metal plate over the motherboard (use the Phillips #00 bit).
Step 3: Disable the display plumes
- 📱 Carefully tuck the black plume of the display (it is attached with a latch). Don't pull the wires, just the connector!
- 🔍 Check if there is a protective tape under the plume - it must be removed before installing a new screen.
Battery's off.|Removed metal plate from the board|Display and touchscreen plumes disconnected|Old glue removed from the frame|New module tested for performance (lighting and touch test)-->
Now we can start removing the old display, if it cracks, stick tape on the surface to prevent fragments from spreading, slid the screen with a spatula, and slowly separate the frame, heating the problem areas with a hair dryer, remove the glue residue with alcohol or acetone.
⚠️ Attention: On the Redmi 5 Plus, the touchscreen plume runs under the battery. If you don't plan to replace it, don't pull the battery out completely -- just raise it 1-2 mm to release the plume.
Installation of a new display: nuances and errors
Before installing a new module, be sure to check its operability by connecting it to the board without fixing with glue.
- Connect the display plumes and touchscreen.
- Connect the battery and turn on the phone.
- Check the backlight (whether there are dark spots), the sensitivity of the touch (swipe your finger all over the screen) and color reproduction (open the white image - there should be no yellowness).
If it works, you can fix the screen. Here are 3 ways to attach, from the most reliable to the most risky.
| Method | Pluses | Cons | Cost |
|---|---|---|---|
| Double-sided 3M Scotch | Easy replacement, no residues. | It can unstick when heated. | 100-200 rubles. |
| Glue B-7000 | Strong fastening, moisture-resistant | Difficult to remove during re-repair | 150-300 rubles. |
| Liquid glue (LOCA) | Perfect sealing | Requires UV lamps, is difficult to apply | 500-1000 rubles. |
For beginners, bilateral scotch is optimal 3M — It's easy to apply, and if you make a mistake, you can re-glue it. B-7000 It's good if you're confident in your skills. LOCA It is better to leave it to professionals - it requires perfectly smooth application and polymerization under the UV lamp.
After the screen is fixed:
- Make sure there are no gaps between the frame and the display.
- Connect the plumes and battery, assemble the phone in reverse sequence.
- Turn on the device and check the touchscreen again (sometimes after assembly, “dead” zones appear due to a compressed plume).
💡
If the display flickers after replacing or the backlight is uneven, check if the plume fits tightly to the connector on the board. Often the problem is solved by reconnecting.
Frequent problems after replacement and their solutions
Even if you did everything according to the instructions, Redmi. 5 Plus can bring surprises.-5 problems and ways of eliminating them:
1.Tachscrin doesn't work or "gluts"
- 🔌 Check if the touchscreen plume is connected correctly (it is thinner than the display plume).
- 🔄 Restart your phone – sometimes the system doesn’t see a new module the first time.
- 🛠️ If part of the screen doesn't respond, maybe the train will be framed. Take the phone apart and check.
2. Uneven lighting (dark spots at the edges)
- 💡 It's a matrix defect or a bad adhesion. Try gluing the screen evenly.
- 🔍 If the stains are left, the module is defective.
3.The screen spontaneously presses the buttons
- 📱 There's probably dirt or glue between the display and the frame, so take the phone apart and clean the surfaces with alcohol.
- 🔧 Check if the plume of the touchscreen is clamped - this can cause "phantom" touches.
4.The phone does not turn on after assembly
- 🔋 Check if the battery is connected (sometimes the plume falls out during assembly).
- 🔌 Make sure all connectors on the board are locked with latches.
- ⚡ If the phone does not respond to charging, the connector may have been damaged. USB-C break-up.
5. Colors distorted (pink or green)
- 🎨 It's a matrix or plume defect. Try plugging in an old display -- if the problem persists, the charge is to blame.
- 🔧 If the colors normalize when you press the screen - the plume does not fit well to the connector.
What if the display works after the replacement, but there is no image?
How much does it cost to replace the display in the service?
If you are not confident in your abilities, it is better to entrust the repair to professionals.The cost of replacing the screen with the Redmi 5 Plus in service centers in 2026 varies depending on the region and type of module:
| Type of display | Cost of work (ruble) | Total spare parts. | Duration of repairs |
|---|---|---|---|
| Original (OEM) | 1 500–2 500 | 4 000–6 500 | 1-2 hours |
| High-quality analogue | 1 200–2 000 | 2 500–4 000 | 1 hour |
| Budgetary analogue | 1 000–1 500 | 2 000–3 000 | 1 hour |
| Glass only (without matrix) | 2 000–3 500 | 3 000–5 000 | 2-3 hours |
In Moscow services, prices are 10-15% higher than in the regions, and some workshops also charge a surcharge for urgent repairs (for 1 hour) or a warranty (usually 1-3 months).
- 🔧 Do they use original parts or analogues.
- 📋 Do you have a guarantee for work and display.
- 💰 Is the cost of the spare part included in the final price or should it be purchased separately.
The average price of replacing the display "turnkey" in 2026 is 3,500-5000 rubles. If you are offered to do it cheaper than 2,500 rubles, most likely, use a low-quality module or save on glue.
💡
Self-replacement of the display on the Redmi 5 Plus costs 2-3 times cheaper than the service, but requires accuracy. The main risks: damage to the plumes (30% of cases), uneven backlight (20%) and “glitch” touchscreen (15%).
Where to buy a high-quality display for Redmi 5 Plus?
Parts are half the success, and here are 5 proven places to buy a Redmi 5 Plus display without risking marriage:
1. Aliexpress.
- ✅ Wide choice, low prices (from 1,200 rubles.).
- ❌ Long delivery (2-4 weeks), high chance of getting married.
- 🔍 Look for sellers with a rating above 98% and reviews in Russian.
2.Yandex Market/Wildberries
- ✅ Quick delivery (3-7 days), possibility of return.
- ❌ Prices are higher than for Ali (from 2 000 rubles.).
- 🔍 Check the description – often sell “Chinese analogues” under the guise of originals.
Local service centres
- ✅ You can check the display immediately before buying.
- ❌ Prices are inflated (from 3 000 rubles), not always available.
4 Groups in Telegram / VKontakte
- ✅ Original Pulls are often sold at low prices.
- ❌ Risk of running into scammers – be sure to demand a video with a display test.
5. Foreign websites (eBay, Amazon)
- ✅ Quality parts, but expensive delivery.
- ❌ Prices bite (from 4000 rubles), customs duties are possible.
When buying, pay attention to:
- 📋 Labeling: Original modules have Xiaomi and Redmi 5 Plus inscriptions on the plumes.
- 🔍 Status. OCA-If the film is damaged, there will be divorces.
- 💡 Backlight test: The seller must send a video with the white screen on (no dark spots).
Alternative repair methods: when replacement is not needed
A broken display doesn't always require a full replacement, and in some cases, you can get by with cheaper repairs.
Replacement of glass (without matrix)
- 💰 Cost: 1,500–2,500 rubles (instead of 4,000–6,000 for a full module).
- ✅ Suitable if the matrix is intact, and only glass cracked.
- ❌ Complicated process – requires skills to work with LOCA-glue and UV lamp.
2. Repair of the plume
- 💰 Cost: 800-1 500 rubles.
- ✅ Helps if the screen flickers or part of the display doesn't work.
- ❌ Not all services are taken for soldering plumes - there is a great risk of damaging the fee.
3. Programmatic calibration of the touch screen
- 💰 Cost: Free (if you do it yourself).
- ✅ Sometimes it helps if the touchscreen “floats” or reacts incorrectly to touch.
- ❌ Will not solve the problem of physical damage to the plume or matrix.
To calibrate the touchscreen on the Redmi 5 Plus:
- Go to Settings → System → Additional → Screen Calibration.
- Follow the instructions on the screen (click on the dots that appear).
- Reboot the phone.
If the calibration did not help, and replacing the plume or glass is too expensive, consider buying a used Redmi 5 Plus with a working screen. On Avito, such phones sell for 3,000-5,000 rubles.