Xiaomi’s Redmi Note series has been popular for years with its price-performance mix. However, no lithium-polymer power supply lasts forever, and over time, even the most reliable battery loses its capacity. If your Redmi Note 6 Pro starts to run out quickly, shut down in the cold or at 20-30%, it’s a sure sign that the chemical’s life is exhausted.
Many users are afraid to open the case of the smartphone yourself, fearing damage to the plumes or break the tightness. Indeed, modern gadgets require accuracy, but the model Redmi Note 6 Pro is designed logically enough that allows you to carry out the replacement procedure at home. You do not need expensive professional equipment, just a basic set of tools and compliance with a certain sequence of actions.
In this article, we will take a look at every step of the process, from the preparation of the workplace to the final assembly of the device. You will learn how to properly unplug the back cover, which plumes require special attention and how to avoid common mistakes. A competent approach will allow you to save money on services of the service center and extend the life of your gadget for several years of active operation.
Diagnosis of battery status and preparation of tools
Before you start disassembling, make sure that the problem is the physical wear of the battery, not software failures or background processes. Check the power consumption statistics in the Settings → Battery and Performance menu. If the discharge schedule shows sharp jumps or the device turns off with a residual charge of more than 10%, this is a clear signal to replace. Also note the appearance of the case: bloating of the battery often leads to the layering of the back cover or the appearance of gaps.
To successfully perform the repair, you will need a specific set of tools that can be purchased at radio parts stores or marketplaces.Do not try to use kitchen knives or thick screwdrivers, as they can damage plastic latches or break glass.
- 🔧 A set of precision screwdrivers (required the presence of Torx bits) T5 cross-block PH000)
- 🎹 Plastic mediators or shoulder blades for opening the body
- 🌡️ Hair dryer building or household heating pad for softening glue
- 🧲 Magnetic mat or organizer for screws
⚠️ Warning: Before starting any work, be sure to completely turn off the smartphone. Attempting to disconnect the battery plume or display under voltage can lead to a short circuit and failure of the power controller on the motherboard.
Organize the workplace so that all parts are at hand and the lighting allows you to see small screws. Lost microscopic bolt can cause rattles of the case or damage to internal components during assembly. SIM-Memory card before the procedure.
☑️ Preparation for repairs
Removal of the back cover and dismantling of components
The rear panel of the Xiaomi Redmi Note 6 Pro is attached to a two-part glue and is held by screws under decorative plugs. First, heat the perimeter of the body with a hairdryer to a temperature of about 80-90 degrees Celsius. Keep the heat source at a distance of 3-5 cm and constantly move it so as not to overheat individual areas of glass or plastic. Check the readiness of the glue should be carefully, trying to insert the mediator into the gap between the frame and the cover.
Once the glue has softened, insert the plastic blade into the corner of the device and smoothly guide it along the edges, cutting the adhesive layer. Don't put too much effort into preventing the back panel from cracking. When the lid is removed, the inner layout will open to your eye. The first thing you need to do is to twist the screws that lock the protective bar that covers the connectors of the plumes. They're usually about 10-12 pieces, and they can be of different lengths, so it's important to remember the location of each.
You take the metal bar off, you get access to the connectors, the first thing you do is you detach the battery plume, you do this with antistatic tweezers or a plastic spatula, you put the connector up from the bottom up, and only after you turn off the battery, you can safely unplug the plumes of the display, the touchscreen and the other modules, and then you twist the screws that hold the battery itself, and the screws of the lower clamps.
💡
When unscrewing the screws, spread them in the same order as they were removed from the case. Rotors of different lengths, installed in their holes, can break through the motherboard or cause a circuit.
The battery itself in the Redmi Note 6 Pro is also planted on glue, but less aggressive than the lid. It is convenient to use special suction cups or a thin plastic card to remove it, which must be carefully promoted under the power cell. In no case do not try to smear the battery with sharp metal objects - a puncture of the lithium polymer cell causes instant ignition of the electrolyte.
Technical specifications and selection of a new battery
Choosing a quality component is 90% of the success of the entire repair. The market is oversaturated with copies and refurbished power cells that may not solve the problem, but also create new ones. The original battery for the Xiaomi Redmi Note 6 Pro has a capacity of 4000 mAh and specific labeling. When buying, pay attention to the presence of a protective BMS (Battery Management System) chip that prevents overcharging and overheating.
The table below shows the main parameters that should coincide when choosing a replacement:
| Parameter | Original | Permissible analogue | Critical. |
|---|---|---|---|
| Model | BN46 | BN46 (compatible) | Yes. |
| Capacity | 4,000 mAh (typical) | 3900-4100 mAh | Yes. |
| Tension. | 3.85V | 3.80V - 3.87V | Yes. |
| Jack | Specific to Xiaomi | A perfect match. | Yes. |
Pay attention to the date of production of the battery. Even if the battery is new, but it has been in the warehouse for more than 2-3 years without recharging, its chemical properties may have deteriorated, the optimal age of the battery is up to 1 year from the date of release, it is also worth checking the integrity of the plume connecting the battery to the board: it should not be broken or scuffed.
How to distinguish the original from the fake?
Don't chase ultra-high capacity if it's declared by the manufacturer-nouneim. The physical dimensions of the cell are limited to the case of the smartphone, and it's impossible to increase energy density without changing the chemical composition or dimensions. 5000-6000 mAh in standard case BN46 — It's a marketing scam.
Installation of a new battery and assembly of the device
The assembly process begins with the installation of a new battery in your regular place. Before gluing, be sure to remove the remnants of the old glue from the frame of your smartphone. This can be done using isopropyl alcohol and a plastic blade. The surface must be clean and defatted to better adhesion the new adhesive layer. Many new batteries already have factory adhesive tape, but sometimes require a special adhesive B-7000 or T-8000 to be applied in a thin layer.
Once the battery is fixed, plug the plume into the motherboard before the characteristic click. Make sure the connector is up smoothly and without skewing. Then you install the bottom pin down bar and twist all the screws. Pay special attention to the screws around the camera module and charging connector - their absence can lead to backlash components.
At this point, you don't have to stick the back cover on, turn on your smartphone and check it's working. If the device is on, displays the right percentage of charge (or at least reacts to the charger's connection) and the touchscreen is working correctly, you can start the final sealing. Put a thin layer of glue around the perimeter of the frame, apply the cover and press it tightly along the entire circuit.
💡
The initial launch of the smartphone before the final gluing of the case allows you to make sure that all the plumes are serviceable and the battery is properly installed, which will save time in case of need for redisassembly.
To fix the lid during the drying process of the glue (usually 1-2 hours), you can use stationery gums, stretching them across and along the body. Do not use heavy loads, as they can crush the display or deform the frame. After drying completely wipe the case from the residue of glue.
Calibration and initial setting
After the battery is replaced, the system may not display the charge level correctly, since the power controller has not yet “acquainted” with the new element. To calibrate, you need to conduct a full charge-discharge cycle. Put the phone on charge when it is off to 100%, then turn it on (without turning off charging) and wait for the indicator to fully fill.
Then use your smartphone intensively until it's 0% and turns off on its own. Then put it back on charge when it's off. This procedure will help the BMS controller record current capacitance and voltage values, usually one or two cycles is enough to stabilize the readings.
The software also recommends checking system updates. Go to Settings → About Phone and click on MIUI. Sometimes manufacturers release patches that optimize power consumption for new batches of batteries. It is also worth resetting the battery usage statistics in the developer menu, if this option is available in your firmware version.
Frequent errors and precautions
Self-repair is always a risk, and knowing the typical mistakes will help you avoid them. One of the most common problems is that the touchscreen plume is damaged when the back cover is not neatly removed. The plume runs very close to the edge, and inexperienced craftsmen often cut it with a blade or a mediator. Always monitor the depth of penetration of the tool.
Another mistake is ignoring the heat pads. The Redmi Note 6 Pro uses special graphite pads and a thermopast to remove heat from the processor and the charge controller. If you damage or lose them during disassembly, be sure to replace them with similar ones. The lack of heat sink will overheat and quickly degrade the new battery.
⚠️ Warning: If you smell a sharp chemical smell during operation, or notice that the battery is rapidly and intensely heated, immediately stop working, take the device out into an open space and place it in a non-combustible container.
Also, remember static electricity. In winter or in dry rooms, the risk of static breakdown increases. Before touching the internal components of a smartphone, touch a grounded metal object or use an antistatic bracelet. The chips of a modern smartphone are very sensitive to discharges that are not even felt by a person.