Connecting a satellite dish to a Xiaomi TV: from choosing a cable to setting up channels

Connecting a satellite dish to a Xiaomi TV seems like a challenge only at first glance. In fact, the process consists of three key steps: the right physical connection, adjusting the settings in the TV menu and finding channels. TV Redmi - the use of a hybrid tuner DVB-S/S2, It supports most of the current satellite standards, including MPEG-4 and H.265 (HEVC). However, not all models are built-in. CI-Slot for conditional access module – this is important to consider when choosing a satellite TV package.

In this article, we will explore how to connect a dish to a Xiaomi TV without a console, what cables and adapters you might need, and how to set up satellite channels manually or through automatic search. We will focus on common errors, such as why the TV does not see a signal even when connected correctly, or how to solve the problem with “no services” in the settings menu. If your Mi TV is released after 2019, it most likely supports DiSEqC 1.0/1.1, a protocol for managing multiple satellites through a single cable.

What Xiaomi models support satellite TV without a console

Not all Xiaomi TVs have built-in satellite tuner, and below is a table of compatibility of the main series with key characteristics. DVB-S2, To view paid channels (for example, Tricolor or NTV-Plus) may require an external CAM-access-card.

If your model is not listed in the table, check the specifications on the official Xiaomi website or in the TV menu: go to Settings → About TV → Specifications. Please note that even with a DVB-S2 tuner, some operators (for example, MTS TV) may require the use of their console due to proprietary encryption.

⚠️ Attention: Xiaomi TVs with Google prefix TV (Like Mi. TV A2 2023) often lacks satellite tuner, in which case the connection of the dish is possible only through an external receiver on the Internet. HDMI.

Necessary tools and components

Before you connect, make sure you have everything you need. Here's the minimum set:

• 📡 Satellite dish (diameter from 60 cm for Ku-band)
• 🔌 LNB-converter (single or universal) Twin/Low Noise)
• 📺 Coaxial cable (RG-6 75 ohm wave-resistance)
• ⚡ F-connectors (2 pcs for cable compression)
• 🔧 Krimper (crumpling tool for connectors)
• 📶 DiSEqC switch (if you connect multiple satellites)

For models without CI-slots (for example, Redmi Smart) TV) may be required additionally:

• 💳 CAM-module (e.g. Neotion Viaccess for Tricolor»)
• 🔑 Smart card of the satellite TV operator
• 🔄 adapter CI→USB (port-model USB-C)

Important: RG-6 cable should be whole - no twists or rations, as they degrade the signal. If the length is more than 30 meters, use a signal amplifier (LNB with an output of 0/12V).

Step-by-step instructions for physical connection

Now, to the process of the connection, follow the instructions in strict order to avoid errors.

1. Turn off the TV (remove the plug from the plug) and prevent static electricity from damaging the ports.
2. Connect the coaxial cable to LNB-Make sure the F-type connector is tightly twisted (but not pulled over!).
3. Lay the cable to the TV, avoiding sharp curves (radius at least 5 cm).Do not lay it near sources of interference (for example, a Wi-Fi router or microwave).
4. Connect the cable to the SAT IN (or DVB-S) connector on the back of the TV. On Xiaomi models, it is usually signed ANTENNA/SAT and painted red.
5. Turn on the TV and wait for the full MIUI TV load.

If you have multiple plates or a DiSEqC switch, plug it into the cable that goes to the TV. The circuit is: Plate → LNB → DiSEqC → Cable → TV.

Cable is tightly fixed on LNB| F-type connector not damaged | TV on network | Correct signal source (SAT) Selected | No visible cable damage-->

⚠️ Note: If you connect the plate through the receiver (set-top box), use HDMI-high speed cable (versions) 2.0 or higher) for signalling 4K@60Hz. In the TV menu, select the source. HDMI, port to which the prefix is connected.

Satellite channels set up in the Xiaomi TV menu

After the physical connection, you need to adjust the satellite settings in the TV menu. The interface may vary slightly depending on the version of MIUI TV, but the general logic remains.

Steps to set up:

1. Press the Menu button on the remote (or the Settings button on the back of the TV).
2. Go to Settings → Channels → Satellite TV setup.
3. Choose Manual Search (for power users) or AutoSearch (for beginners).
4. Enter satellite parameters: 📡 Satellite: e.g. Eutelsat 36E (for "Tricolor" or ABS-2 75E (for NTV-Plus»). 🔍 Frequency (MHz): 12226 (for "Tricolor" or 11766 (for NTV-Plus»). 📶 Symbolic speed: 27500 or 43400 (depends on the operator). 🔄 Polarization: Horizontal (H) or Vertical (V). 🔑 FEC: usually 3/4 or 2/3.

Search

If you use CAM-module, before searching for channels:

1. Insert the module in CI-slot (usually located on the side or back of the TV).
2. Insert the smart card into the module (chip up!).
3. In the TV menu, select Settings → CI-module → Activate.
4. If the indicators are low, adjust the position of the plate: 🔧 Relax the nuts on the attachment. 📶 Slowly turn the plate horizontally (azimuth) and vertically (angle of place). 📊 Watch for changes in signal level on the screen.

Check the cable for cliffs or circuits with a tester.

💡

If you connect a plate to a Xiaomi TV via a console and the image is behind the sound, try turning off the Lipsinc function (AV Sync) in the console menu or setting the sound delay manually (usually in the range of 0–200 ms).

Multiple Satellite Configuration (DiSEqC)

If you want to receive signals from multiple satellites (e.g. Eutelsat 36E and Astra 4A), use a DiSEqC switch. Xiaomi TVs support DiSEqC 1.0 (for 4 satellites) and 1.1 (for 16 satellites).

1. Connect the plates to the switch, and its output to the TV.
2. From the TV menu, select Settings → Channels → DiSEqC settings.
3. Activate DiSEqC 1.0/1.1 and specify ports for each satellite (e.g. Port A – Eutelsat 36E).
4. For each satellite, perform a manual search with individual parameters.

Example of configuration for two satellites:

DiSEqC 1.0:




Port 1 → Eutelsat 36E (Tricolor)




Frequency: 12226 MHz




Polarization: Horizontal (H)




Symbolic speed: 27,500





Port 2 → Astra 4A (NTV-Plus)




Frequency: 11766 MHz




Polarization: Vertical (V)




Symbolic speed: 27,500

⚠️ Note: When using DiSEqC 1.1, avoid connecting more than 8 satellites – this can cause delays when switching channels due to the limitations of the TV processor.

💡

If you are using a motor plate (with a rotary mechanism), you need to activate the USALS (Universal Satellite Automatic Location System) option in the Xiaomi TV menu and enter the coordinates of your location (latitude / longitude).

Update the firmware to improve compatibility

If the TV doesn’t recognize the satellite signal or if there are errors when searching for channels, the reason may lie in outdated firmware. Xiaomi regularly releases updates that correct bugs in the work. DVB-This is how to update the software:

1. Go to Settings → About TV → System Update.
2. Click Check for updates.
3. If a new version is available, confirm installation. The TV will restart automatically.

If the problem is in the TV, reset the tuner settings.