How to connect a rear view camera to a Xiaomi DVR: full instruction 2026

Xiaomi DVRs are some of the most popular devices for traffic capture, but they don't just go to the front. Connecting a rear-view camera greatly enhances the system's capabilities: you get a full view of the car, make parking easier and make maneuvers safer. However, many owners have difficulty integrating an additional camera, from mismatches between connectors to problems with display settings.

In this article, we will analyze all ways of connecting (wired, wireless, via adapters), compatibility with Xiaomi models. 70Mai, MiVue and others, and the typical errors that are made during installation, especially pay attention to the hidden laying of cables and setting up automatic image switching when you turn on rear gear. If you have already tried to connect the camera, but encountered artifacts on the screen or the lack of signal – here you will find solutions.

First, decide which type of camera you want: analog (cheap but wired) or digital (wireless, but more expensive). 70Mai Rear Camera, but universal models with support for the standard will also work. NTSC/PAL. The main thing is to check the connector: most Xiaomi registrars have a mini.-USB or A/V-in (yellow-tulip").

1. Compatibility of rear-view cameras with Xiaomi DVRs

Not all cameras will fit your recorder, but the basic compatibility criteria are:

• 🔌 Type of connector: Xiaomi 70Mai Pro and MiVue 795 — miniature-USB, old models, for example, 70Mai Midrive D06) — A/V-in (RCA).
• 📺 Signal format: Xiaomi registrars work with NTSC (United States/Japan) or PAL (Europe) Please specify the device settings.
• 🔋 Power: The camera should receive 5V/12V — Check if there is a voltage converter in the kit.
• 📏 Viewing angle: optimal 120°–170°. Cameras with an angle >170° They cause severe distortions around the edges.

Xiaomi’s official cameras (e.g., the official cameras, 70Mai Rear Camera RC06) They're guaranteed to be compatible, but they cost more than universal ones, and these often require adapters or manual video format adjustments:

⚠️ Note: If your registrar does not have a separate input for the camera (e.g. Xiaomi MiVue) J150), Connection is possible only through HDMI-input (an additional signal converter is required). >5 inches.

2. Necessary tools and components

Before starting work, prepare:

• 🔧 Screwdriver with a cross bat (to remove the skin of the salon).
• 🔌 Multimeter (testing voltage on the backwires).
• 📦 Camera kit: camera itself, power cable, video cable, mounts.
• 🔗 Adapters (if connectors do not match): for example, RCA → miniature-USB or USB-A → USB-C.
• 🎨 Heat shrinkage and plastic screeds for cable fixation.

Hidden cables may require a dismounting tool (plastic blades) and a corrugated tube (to protect the wires from rubbing). If you plan to connect the camera to a reversing lamp, prepare crimping terminals or soldering.

Clarify the DVR connector (USB/RCA/HDMI)

Check the second camera recorder (in the instructions)

Determine the type of signal (NTSC/PAL) device settings

Measure the length of the cable from the trunk to the registrar (standard - 5-7 meters)

Buy a camera with a viewing angle of 120°–150° minimally-->

Critical detail: If your recorder doesn’t have a separate input for the camera (like the Xiaomi MiVue 750), the connection is only possible via a splitter. HDMI or firmware replacement (unofficial method, risk of loss of warranty).

3. Step-by-step instruction: wired connection

This is the most reliable way, but it requires careful laying of the cables.

1. Remove the trunk lining (usually attached to clips). Carefully apply the plastic with a screwdriver, starting at the corners.
2. Place the camera above the license plate or on the back window and attach it to double-sided tape or screws (depending on the model).
3. Connect the camera power: 🔋 Option 1: To the reversing lamp wires (plus — +12V when the transfer is included, minus - the body). 🔌 Option 2: To a permanent +12V (e.g. from the lighter) through the relay so that the camera only works when the rear gear is turned on.
4. Lay the video cable along the existing wiring (for example, on the thresholds or under the mats), fasten it with screeds every 30-40 cm.
5. Connect the cable to the registrar: For mini-USB: insert into the corresponding connector (usually signed) CAM IN). For RCA: Use yellow (video) and red/white (audio if needed) inputs).
6. Set up the Registrar: Select Settings from the menu → Rear-view camera → Set the signal format (NTSC or PAL) Activate Auto-Switch option (if supported).

Once connected, check the system: when you turn on the back, the camera image should automatically appear on the recorder screen.

• 🔌 Correct power connection (multimeter).
• 📺 Signal format in the Registrar settings.
• 🔗 Integrity of cable (curves, breaks).

💡

If the camera image is upside down, look for the Flip Image or Mirror option in the registrar menu and turn it on. In some Xiaomi models, this setting is hidden in the engineering menu (press the Menu button for 10 seconds).

4. Wireless connection: pros and cons

Wireless cameras (e.g. Xiaomi Mi Home Camera) 2K It's convenient because it doesn't require a video cable. But there are limitations to this method:

• ⚡ The power still needs to be supplied by wire (from the reversing lamp or battery).
• 📶 Delay of signal: up to 0.5-1 seconds (critical for dynamic parking).
• 🔋 Possible interference when working near powerful sources Wi-Fi/Bluetooth.
• 💰 Cost: wireless solutions are more expensive than wired 1.5-2 times.

To connect:

1. Install the camera and bring power to it (similar to the wired method).
2. Connect the Wi-Fi transmitter to the camera (usually included).
3. In the Registrar settings, select the Wireless Camera → Searching for devices.
4. Connect the devices (may require input) PIN-code specified on the transmitter body).

The wireless method is suitable for temporary use or if it is impossible to lay a cable (for example, in a rented car).

5. Setup automatic image switching

To the rear-view camera is turned on automatically when reversing, you need:

1. Connect the camera power to the reversing lamp (as described in section 3). +12V, And the recorder will get the signal.
2. Activate the function in the menu: Go to Settings → Rear-view camera → Auto-switch. Select On and set the return delay to the main camera (usually 5-10 seconds).
3. Check Connection Polarity: If the camera doesn't respond to the backshift switch on, swap places + And on the power wires. Some Xiaomi models, for example, 70Mai Pro) has a separate entrance ACC switch-control.

If the automatic switching does not work:

• 🔧 Check the integrity of the wire from the reversing lamp to the camera (a break is possible).
• 📋 Make sure that the menu of the Registrar selects a trigger for nutrition (not the signal with the signal). CAN-tire).
• 🔄 Restart the registrar (sometimes a firmware failure blocks the function).

💡

If your car is equipped with a can-bus (modern models), it may be necessary to automatically switch. CAN-It reads the signal that you're turning on the back gear directly from the onboard computer, which is more reliable than connecting to the flashlight.

Typical problems and their solutions

Even with the right connection, there can be problems.

⚠️ Warning: If the main camera of the recorder stopped working after connecting the camera, reset the device to factory settings (Settings) → Reset. This often helps with driver conflicts. Do not update the firmware during reset, this can lead to the "bricking" of the device.

If the problem is not resolved, check:

• 🔌 Power voltage on the camera (should be) 12V ± 0.5V).
• 📡 Cable length: signal loss is possible if you exceed 7 meters (use an amplifier).
• 🔄 Registrar firmware: Xiaomi forums often post patches to support unofficial cameras.

7. Hidden cable installation: tips and life hacks

To ensure that the wires do not spoil the view of the cabin, follow these recommendations:

• 🚗 Threshold pad: Remove plastic pads on the sills (mounted on clips). Run the cable along the existing wire harness. Secure screeds every 40 to 50 cm.
• 🪟 Through rubber door seals: Bend the seal carefully between the body and the door. Pass the cable without clamping it. Put the seal back in place (you can use silicone lubricant to facilitate the process).
• 🔌 Power connection without soldering: Use crimping terminals or "vampire" connectors to connect to the reversing light wires. Sequester connections with shrinkage or tampering.
• 🎨 Camouflage cable in the trunk: Lay the wire along the regular harnesses, fixing it with adhesive mounts. In places where the cable crosses the moving parts (for example, the trunk lid), use a corrugated tube.

If you don't want to take off the skin, you can put a cable under the mats, but keep in mind that it can interfere with cleaning the cabin or moving the seats. CAN-tires (e.g. Volkswagen, Skoda) are better to use specialized adapters so as not to interfere with the regular wiring.

💡

To prevent the cable from creaking when moving, wrap it in foam tape in the contact areas with plastic panels, which also protects the insulation from rubbing.

8. Alternative ways of connecting

If your Xiaomi registrar doesn’t support a second camera, consider these options:

• 📱 Using your smartphone as a second camera: Install a recorder app on your phone (like DailyRoads Voyager); fasten your smartphone on the back window and connect it to the recorder via Wi-Fi (if streaming is supported); minus: fast battery drain and overheating of the phone.
• 🖥️ Connection through HDMI-input (for screen recorders): A signal converter (e.g, A/V → HDMI). Connect the camera to the converter and it to the HDMI-in recorder (~3000–5000 ₽).
• 🔄 Replacement of the Registrar firmware: Some models (e.g, 70Mai Pro) can be flashed with custom firmware with support for the second camera, risk: loss of warranty and possible "brike" of the device. 4PDA or XDA-Developers.

For owners of Xiaomi MiVue C300R And other models without input for the camera, the only reliable way is to buy a separate monitor (for example, Xiaomi Mi Rearview Mirror) and connect the camera to it.

💡

If you choose an alternative way of connecting, please note that the warranty on the registrar can be canceled when interfering with firmware or disassembling the case.

FAQ: Frequent questions about connecting a rear-view camera