Preparing Xiaomi air grill to work: from unpacking to the first launch

Xiaomi Airgrill is a multifunctional device that combines the capabilities of a convection oven, deep fryer, grill and even dryer. However, before its first use, it must be properly prepared: assemble, connect, calibrate and adjust. Careless attitude to this stage can lead not only to poor cooking results, but also to a device failure or even a fire situation.

In this article, we will take a look at all the steps from unpacking the box to test run, and give recommendations for safe operation and care of the aerogrill, paying special attention to the nuances that the manufacturer often misses in the instructions: how to install the heating element correctly, why it is important to burn the device before first use, and how to avoid common assembly errors.

If you’ve just purchased one of the models — whether it’s the Mi Smart Air Fryer, Mijia Air Fryer Pro or another Xiaomi version — this guide will help you avoid typical problems and maximize the potential of the device.

1. Unpacking and inspection of equipment

The first step is to unpack the box carefully, and make sure you do this on a level surface so that you don’t damage fragile elements (like a glass flask or heating element).

• 📦 The main unit with a heating element and a control panel
• 🔄 Glass flask (sometimes with non-stick coating)
• 🍳 Basket for products (metallic or ceramic coated)
• 📄 Instructions for operation (in Chinese/English)
• 🔌 Power cable (in some models removable)
• 🔧 Additional accessories: grille, forceps, pallet for collecting fat (depending on the model)

It's important to check:

• 🔍 Glass bulb integrity – even small cracks can lead to depressurization and breakage.
• 🔌 Power cable condition – it should not be twisted or damaged.
• 📏 Conformity of the serial number on the device and in the warranty card (if attached).

If the kit is missing or you find defects, do not turn the device on – immediately contact the store or service center Xiaomi for replacement. Also save the box and package until the end of the warranty period: they may be needed when returning or repairing.

2. Assembly of aerogrill: step-by-step instructions

The assembly of most Xiaomi aerogrill models is intuitive, but there are a few key points that are often overlooked.

1. Installation of the bulb: Carefully place the glass bulb on the base of the device. Make sure it sits tightly in the slots - there should be no backlash or skews. In models with automatic locking (for example, Mijia Air Fryer Pro), you will hear a click.
2. Heating member fastening: Insert the heating module in the top of the bulb. In some models, it is fixed by turning counterclockwise (see instructions).
3. Installation of the basket: Place the basket inside the bulb. It should be free to take out, but not hang around with a light sway.

Typical errors in assembly:

• ❌ Flake fit - leads to leakage of hot air and uneven cooking.
• ❌ Twisting the power cable - can cause a short circuit.
• ❌ Ignoring protective film – new devices often have stickers or film on the glass that must be removed before first turning on.

If your model is equipped with a touch panel (for example, Mi Smart Air Fryer), make sure that it responds to touch. For this, light touch is enough - you do not need to press with force. In mechanical models, check the smooth rotation of the temperature and time control handles.

3. Electrical connection and first switching on

Before connecting the aerogrill to the socket, make sure that:

• 🔌 The socket is designed for the power of the device (usually 1500-1800 W). Do not use extension cords or tees - this can lead to overheating.
• 🌡️ The device stands on a flat, stable and non-combustible surface (for example, a countertop made of stone or metal).
• 🚫 Within a radius of 30 cm there are no flammable objects (curtains, paper, plastic).

When first activated:

1. Put the plug in the socket.
2. Press the power button (usually marked with Power or icon) ⏻).
3. Wait for the beep or flash of the indicator (depending on the model).
4. Start the "roast" mode (if any) or set the temperature to 200°C for 10-15 minutes without food, this will remove factory odors and oil residues from the internal surfaces.

💡

If the aerogrill emits a slight smell of plastic on the first turn on, that's fine, but if the smell is sharp or the smoke comes from under the bulb, turn off the device immediately and check that the assembly is correct.

In Wi-Fi models (such as Mi Smart Air Fryer), you may need to connect to the Mi Home app after the first switch on.

1. Download the Mi Home app on your smartphone.
2. Sign up or sign in to your Xiaomi account.
3. Click Add Add the device → Kitchen. → airgrill.
4. Follow the instructions on the screen (scanning may be required) QR-code-on-device).

4 Calibration and adjustment before first use

Calibration is required to ensure that the aerogrill accurately maintains the desired temperature. In most Xiaomi models, this process is automated, but there are nuances:

After calibration, it is recommended to check the accuracy of the thermostat.

1. Place the thermometer for the oven (preferably digital) in the basket.
2. Set the temperature to 180.°C. 10 minutes.
3. Compare the thermometer and the aerogrill display — ±5°C.

If the difference is greater, contact the service center - this may indicate a malfunction of the temperature sensor.

5.First preparation: test run

Before you cook a full meal, run a test run with a simple product, such as slices of potatoes or slices of bread.

• 🍟 Check the uniformity of the roasting.
• 🔥 Estimate the heating rate.
• 👃 Make sure the smells of the factory lubricant are completely gone.

Instructions for test launch:

1. Cube the potatoes (size) 2×2 centimeter).
2. Lubricate a basket of 1 tsp of vegetable oil (use a spray for even distribution).
3. Select the Frieder or set the temperature 190°C. 15 minutes.
4. After 7-8 minutes, shake the basket for even cooking.

Evaluate the result:

• ✅ Potatoes are evenly golden - the device works correctly.
• ⚠️ Part of the pieces are burned and part is raw - check the placement of the basket or the density of the bulb closure.
• ❌ Potatoes not roasted - possibly faulty heating element.

💡

If the test preparation is successful, you can move on to more complex dishes, but remember: Xiaomi aerogrills often require a temperature reduction of 10-15.°C compared to recipes for traditional ovens.

6 Safety and care after first use

After the test run, be sure to follow the following steps:

1. Cleaning the basket and flasks. Don't use abrasive detergents, they'll damage the non-stick coating. Enough warm water with a soft detergent and sponges. You can use baking soda to remove fat.
2. In models with a removable ring (for example, Mijia Air Fryer Pro), make sure that it does not deform and fits tightly.
3. Storage: If the aerogrill is not used for a long time, store it in a dry place with an open flask (to avoid the smell of mustyness).

⚠️ Warning: Never immerse the main electronics unit in water! Use wet cloth to clean the external surfaces. Also avoid using metal brushes - they scratch the coating and shorten the life of the device.

To extend the life of Xiaomi aerogrill, follow these recommendations:

• 🔄 Regularly (every 1-2 months) lubricate the sealing ring with food silicone spray.
• 🌡️ Do not exceed the maximum temperature specified in the instructions (usually 200-230).°C).
• 🔌 Always remove the plug from the socket after use – this will prevent electronic components from overheating.

7. Frequent mistakes and how to avoid them

Even experienced users sometimes make mistakes when they first use an air grill, and here are the most common ones and ways to prevent them:

Another common problem is the smell of burning on the first switch, and if it doesn't go away after 2-3 uses, it might indicate:

• 🔥 Oil or fat on the heating element (must be cleaned manually after cooling).
• 🔌 Thermostat malfunction (diagnosis is required at the service center).

⚠️ Note: If the Xiaomi aerogrill (suddenly shuts off) during cooking, do not immediately try to turn it on again.Let the device cool for 10-15 minutes - this may be an overheating protection.Repeated attempts to turn on without cooling will lead to breakage.

FAQ: Answers to Frequent Questions