Regular maintenance is a guarantee of its long service, and wireless vacuum cleaners Xiaomi or Dreame are no exception. Over time, the container accumulates dust and the filters settle the smallest particles, which inevitably leads to a decrease in suction power. Many users notice that the device begins to cope with cleaning or makes extraneous sounds, unaware that the problem is solved by simple cleaning.
In this article, we will take a look at the maintenance process of different models, from compact manual options to powerful vertical stations, you will learn which units require weekly attention and which are enough to maintain every few months, timely cleaning will not only restore the former performance, but also prolong the life of the battery and engine.
Ignoring the need to care for the filter system can lead to overheating of the engine. The dust that clogs the filter pores creates resistance to airflow, causing electronics to work in extreme mode. So the question of how to clean the vacuum cleaner Xiaomi Dreame is fundamental to each owner of this equipment.
Preparation for cleaning and safety measures
Before any manipulations are initiated, you need to disconnect the device from the charging station and remove the battery if the design of the model allows it.This is a basic safety rule that will prevent the engine from starting accidentally during disassembly. Also make sure that you have free space with good lighting so that small parts do not get lost.
You'll need a minimal set of tools: a cross screwdriver (often needed to remove lids), scissors to remove coiled hair and possibly a soft brush. Don't use aggressive chemicals or solvents, as they can damage the plastic of the container. The plastic elements are quite durable, but chemical reagents can cause them to cloud or crack.
⚠️ Warning: It is strictly forbidden to wash the main body of the vacuum cleaner, handle or block with the engine with water. Moisture can enter the interior, which will lead to short circuit and irreversible failure of the electronics.
It is recommended to clean over the trash can or on the spread newspaper to remove the dirt immediately.If you plan to wash the filter elements with water, make sure you have room for their quality drying. The drying process can take up to 24 hours, so plan the maintenance time in advance.
☑️ Preparation for maintenance
Cleaning of the main dust collector
The first step is always to release the dust container. In the Dreame V11, V12 or Artemis models, the process is similar: press the unlock button and remove the cyclone block. Do not try to knock the dust out with blows on hard surfaces, as this can damage the internal partitions of the cyclone.
To clean effectively, use a soft dry cloth or a microfiber napkin. If there are fat spots on the walls (for example, after cleaning in the kitchen), the cloth can be slightly moistened with water, but then must completely dry. The cyclonic system is sensitive to adhesions that can disrupt the aerodynamics of the airflow.
- 🧹 Carefully wipe the internal walls of the container, removing the dust plaque.
- 🌬️ Blow the engine protection net located at the top of the container.
- 🔍 Inspect rubber seals for cracks or contamination.
Pay special attention to the inlet through which air enters the engine, which often accumulates fine dust that is not visible on a cursory examination, use a dry brush or cotton swab to remove contaminants from hard-to-reach corners, and the purity of this unit directly affects the efficiency of the filtration system.
Washing and care HEPA-filter
A fine cleaning filter, or HEPA-The filter is the heart of the air purification system, and it traps allergens and microscopic dust. The Xiaomi and Dreame vacuum cleaners typically use a multi-layered design that can be washed, but you have to do it right so you don't damage the structure of the fibers.
Remove the filter from the compartment by carefully pulling the special tongue. Wash it under a stream of cold running water until the water is clear. Hot water (above 40°C) is strictly prohibited, as it deforms the synthetic fibers and destroys the filtering properties. Do not brush the filter and twist it.
After rinsing, squeeze the water lightly with your hands, but don't put too much effort into it. Leave the filter to dry in a warm, well-ventilated place in a horizontal position. The process of drying completely takes 12 to 24 hours. Installing a wet filter will cause unpleasant odor and risk damage to the engine.
How often do you change? HEPA-filter?
The frequency of flushing depends on the load: if you clean an apartment with pets, it is worth doing it every two weeks. For normal cleaning, once a month is enough. Regular maintenance ensures that the outlet air remains clean and the suction power does not fall.
Turbobrush maintenance and hair removal
One of the most common problems is winding hair, wool and threads onto the turbobrush shaft, which not only reduces the efficiency of carpet cleaning, but also puts additional strain on the brush engine, which can lead to overheating or a break in the drive belt. Regular cleaning of the shaft is a mandatory procedure.
First, flip the brush and remove the lid by unscrewing the locking screws or snapping the latches (depending on the model). You will see the wound hair. Carefully cut it with scissors along the shaft and remove the bundles. Don't pull the hair sharply so as not to damage the shaft bearings.
| Brush element | Type of pollution | Cleaning method | Frequency |
|---|---|---|---|
| The bristle-shaft | Hair, threads | Scissors, tweezers | Once every 2 weeks |
| Shaft bearings | Dust, dirt. | Dry fabric | Once in 3 months |
| Cap of the compartment | A dust plaque | Wet wipe. | Every time you clean. |
| Contact areas | Oxidation | Alcohol napkin | Six months |
After hair removal, wipe the inside of the brush casing with a wet cloth. Check if the shaft is rotating freely. If you hear a grinding or a shaft spinning with difficulty, you may need to lubricate the bearings or replace them. The movable parts should work silently and easily.
💡
Use a special brush brushing knife if it comes with a kit. Its jagged edge is ideal for quickly cutting and pulling hair out of the bristles without damaging the shaft itself.
Cleaning additional filters and sensors
In many modern models, such as the Dreame V12 pro T20, There are additional filters at the air outlet or in the handle, and they also need to be checked periodically and washed or replaced if necessary. HEPA-component.
Dust sensors, if they're designed, require special attention, and they can become contaminated, causing the vacuum cleaner to misidentify the type of coating or the amount of dust it contains. Rub the sensors with dry soft cloth without pile. Optical sensors are very sensitive to fat fingerprints.
- 👁️ Wipe the dust sensor on the container body with a dry cotton swab.
- 🌬️ Check the filter at the air outlet (if any in your model).
- 🔋 Check the contacts of the battery for oxidation.
If you notice that the pollution indicator is constantly burning, even on the clean floor, it is likely that the sensor is contaminated. Careful cleaning returns the smart functions to work. Don't use alcohol to wipe the plastic lenses of the sensors, you should use special wipes for optics.
Drying and assembly of the device
The most critical stage is waiting. All washed parts must be completely dry before assembly. Residual moisture inside the housing is the main enemy of electronics. Even if the outside part seems dry, there can be water inside the porous filter materials.
Only assemble the vacuum cleaner after you're completely sure that all the components are dry, insert the filters, close the container lids, and secure the turbobrush. Check the density of all the joints: if the container is leaky, the power loss is guaranteed due to the unfiltered air sucker.
⚠️ Warning: Never turn on the vacuum cleaner if there is the slightest doubt that the filters or internal cavities are completely dry.
After the first build, it is recommended to turn the device on at maximum power for 1-2 minutes without nozzles to make sure that there are no extraneous noises and vibrations. If everything goes well, your Xiaomi Dreame is again ready for effective cleaning with factory suction force.
💡
Complete drying of all elements within 24 hours is the only condition that can not be violated to avoid engine failure after wet cleaning.